There is ongoing research to develop lithium ion batteries as sustainable energy sources. Because of safety problems, solid state batteries, where electrolytes are replaced with solids, are attracting attention. Sulfide electrolytes, with a high ion conductivity of 103 S/cm or more, have the highest potential performance, but the price of the main materials is high. This study investigated lithium hydride materials, which offer economic advantages and low density. To analyze the change in ion conductivity in polymer electrolyte composites, PVDF, a representative polymer substance was used at a certain mass ratio. XRD, SEM, and BET were performed for metallurgical analyses of the materials, and ion conductivity was calculated through the EIS method. In addition, thermal conductivity was measured to analyze thermal stability, which is a major parameter of lithium ion batteries. As a result, the ion conductivity of LiH was found to be 106 S/cm, and the ion conductivity further decreased as the PVDF ratio increased when the composite was formed.

The precipitation effect of Al-6%Si-0.4%Mg-0.9%Cu-(Ti) alloy (in wt.%) after various heat treatments was studied using a laser flash device (LFA) and differential scanning calorimetry (DSC). Solid solution treatment was performed at 535 oC for 6 h, followed by water cooling, and samples were artificially aged in air at 180 oC and 220 oC for 5 h. The titanium-free alloy Al-6%Si-0.4%Mg-0.9%Cu showed higher thermal diffusivity than did the Al-6%Si-0.4%Mg-0.9%Cu-0.2%Ti alloy over the entire temperature range. In the temperature ranges below 200 oC and above 300 oC, the value of thermal diffusivity decreased with increasing temperature. As the sample temperature increased between 200 oC and 400 oC, phase precipitation occurred. From the results of DSC analysis, the temperature dependence of the change in thermal diffusivity in the temperature range between 200 oC and 400 oC was strongly influenced by the precipitation of θ'-Al2Cu, β'-Mg2Si, and Si phases. The most important factor in the temperature dependence of thermal diffusivity was Si precipitation.

The effect of precipitation and dissolution of Si on the thermal diffusivity in the Al-Si alloy system is reported in this study and solution heat treatment followed by aging treatment is carried out to determine the effects of heat treatment on the thermal characteristics. The solution treatment is performed at 535 oC for 4 and 10 h and then the specimens are cooled by rapid quenching. The samples are aged at 300 oC for 4 h to precipitate Si solute. The addition of 9 wt% silicon contents makes the thermal diffusivity decrease from 78 to 74 mm/s2 in the cases of solid solution treated and quenched samples. After quenching and aging, the Si solute precipitates on the Al matrix and increases the thermal diffusivity compared with that after the quenched state. In particular, the increase of the thermal diffusivity is equal to 10 mm/s2 without relation to the Si contents in the Al-Si alloy, which seems to corresponded to solute amount of Si 1 wt% in the Al matrix.

By Multiple-measurement method using Inverse Heat Conduction Method and parameter estimation method, thermo physical properties were measured, and its estimation accuracies were compared with other reference data. Values of the thermophysical properties determined from the measurement method are in the range of data reported in the literature. From the above, it should be pointed out that the inverse algorithm and multiple measurement method is particularly simple to code and can be run on the personal computer used for the data acquisition. Especially, the inverse algorithm for a heat flux determination can be practically used in every case where the surface measurement are not accessible and where it is impossible to correctly place some sensors with the body. It is found that the measurement method is more practical, convenient and time-saving than other steady-state methods.

In this study, we study the characteristics of thermal diffusion of cement paste at elevated temperature. Results of the experiments can be used to predict the fire damaged temperatures of concrete, and to recommend proper methods for repair and rehabilitation.

In this study, we study the characteristics of thermal diffusion of cement paste at elevated temperature. Results of the experiments can be used to predict the fire damaged temperatures of concrete, and to recommend proper methods for repair and rehabilitation.