This study was conducted with two ruminally cannulated Holstein steers to examine the effect of micronized and steam flaked corn on ruminal fermentation characteristics. The in situ dry matter degradability after 48 h incubation was the highest (P<0.05) at micronized corn (2.5 mm thickness) compared with steam flaked corn treatments. The steam flacked corn (3.3 mm thickness) was degraded lower (P<0.05) than the 2.9 and 3.1 mm thickness of steam flacked corn. Effective dry matter degradability and the rate of constant were the highest (P<0.05) at micronized corn (2.5 mm thickness) compared with steam flaked corns as well. The in vitro dry matter degradability after 48 h incubation was tended to higher (P=0.088) at micronized corn (2.5 mm thickness) than steam flaked corns, whereas there is no significantly difference between steam flaked corn treatments. Total volatile fatty acid concentration was higher at steam flaked corn (2.9 mm thickness) than micronized corn (2.5 mm thickness) and steam flaked corn (3.1 and 3.3 mm thickness). The acetate : propionate ratio was the highest (P=0.008) at steam flaked corn (2.9 mm thickness) and the lowest (P=0.008) at micronized corn (2.5 mm thickness). Total gas and methane production after 48h ruminal incubation was the highest (P=0.001) at micronized corn (2.5 mm thickness) compared with steam flaked corns. According to these results, the thickness of steam flaked corn as resulted corn processing is believed to do not affect methane production. However, further study is needed to better understand the present results to verify the correlation between corn processing method and their thickness on methane production using the same thickness corns by difference processing methods.
A bulk porous composite with plantinum nano-dispersion was synthesized in air atmosphere through the combination of several in situ reactions, including the pyrolysis of . A mixture of (dolomite), , and LiF (0.5 wt%, as an additive) was cold isostatically pressed at 200 MPa and sintered at for 2 h. The porous composite ( : Pt=99 : 1 in volume) had a uniformly open-porous structure (porosity: 56%) with three-dimensional (3-D) network and a narrow pore-size distribution, similarly to the porous composites reported before. Catalytic Properties (viz., NO direct decomposition and NO reduction by ) of the composite were investigated up to . In the absence of oxygen, the NO conversion rate reached ~52% for the direct decomposition and ~100% for the reduction by , respectively. The results suggest the possibility of the porous composite as a multifunctional filter, i.e., simultaneous hot gas-filtering and in one component.
본 연구에서는 재고미의 사료가치 평가를 위해 무처리(Control)를 비롯한 Extruding, Roasting, Steam 처리구들의 영양소 성분분석, in vitro 소화율, in situ 소화율을 분석하였다. In vitro 실험에서 Extruding은 건물 소화율과 gas 발생량이 타 처리구에 비해 상대적으로 높았고, 가장 낮은 pH를 보였으며, 특히 배양 시간 초기에 소화가 신속히 발생하였다. NH3-N 함량은 배양 6 h 이후에서 Control이 Extruding, Roasting, Steam에 비해 유의적으로 높은 값을 보였고, 이는 가열처리된 단백질의 반추위 미생물의 이용성 저하에 따른 결과로 보이나, 더 정확한 결과를 위해 건물 소화율 분석뿐 아니라 CP 소화율 분석이 필요할 것으로 사료된다. VFA 발생량에서는 Extruding이 다른 처리구들에 비해 배양 6, 12 h에서 유의적으로 높았는데 이는 Extruding 처리구의 분해가 배양 초기에 주로 이어져 발생한 결과로 추정된다. 전분을 발효시키는 박테리아에 의해 높은 비율로 생산되는 propionate 증가 폭에서도 같은 경향을 보였다. In situ 소화율은 in vitro의 소화율과는 다소 차이가 있는 것으로 여겨지나, 이는 실험 방법에 대한 오차로 여겨질 수 있으며, ED(유효분해율)를 통해 in vitro 시험과 소화율의 경향성이 유사한 것을 알 수 있었다. 따라서 본 연구결과를 근거로 상대적으로 적합한 사료가공 처리방법은 무처리, Roasting 및 Steaming인 것으로 보여진다. 또한 무처리(control)의 경우 가공처리에 따른 추가비용 발생이 없으므로 경제적으로 유리할 것으로 판단된다. 재고미가 TMR의 원료로 이용될 수 있다면 국내에서 자급 가능한 사료원료로써 우수한 경제성을 지닐 수 있을 것이다.