Thermal barrier coatings(TBCs) are being applied in many industrial fields such as thermal power generation, aviation and seasonal fields. ZrO2-Y2O3(8%) thermal spray coating powders are commercially used as thermal-barrier coating materials to protect against oxidation and corrosion of heat-resistant alloys at elevated temperatures. Currently, ZrO2-Y2O3(8%) thermal-spray powder is made using the industrial co-precipitation process, which is very complex and requires a lot of time. In this study, orthorhombic ZrO2 and Y2O3 powders were fabricated by mechanical mixing, which is more economical than the co-precipitation process. A tetragonal, yttria-stabilized zirconia(YSZ) coating-layer was produced by plasma spraying, using orthorhombic ZrO2-Y2O3(8%) powder. Our experimental results indicate that ZrO2-Y2O3(8%) mixed powder can be used economically in industry because it is no longer necessary to make this powder by liquid and gas-phase methods.
In this study, intermediate-mixed powders were prepared by loading zirconia powders initially in a ball-mill jar and loading alumina powders afterward; the initial-mixed powders were produced by loading zirconia and alumina powders together in the ball-mill jar. The effect of such differences in mixing method on the mechanical properties was investigated. In intermediate-mixed powders, the volume fraction of large particles slightly increased and, simultaneously, zirconia particles formed agglomerates that, due to early ball-mill loading of the zirconia powders only, were more dispersed than were the initial-mixed powders. For the intermediate-mixed powders, zirconia agglomerates were destroyed more quickly than were initial-mixed powders, so the number of dispersed zirconia particles rose and the inhibitory effect of densification due to the addition of a second phase was more obvious. In the microstructure of intermediate-mixed powders, zirconia grains were homogeneously dispersed and grain growth by coalescence was found to occur with increasing sintering temperature. For the initial-mixed powders, large zirconia grains formed by localized early-densification on the inside contacts of some zirconia agglomerates were observed in the early stages of sintering. The intermediate-mixed powders had slightly lower hardness values as a whole but higher fracture toughness compared to that of the initial-mixed powders.
The recent trend of miniaturization and high performance of vehicle engines has put an urgent necessity for the development of valve seats which can operate under more severe conditions. In order to develope valve seat material that has the most excellent wear resistance at operating temperature of engine through improvement of the progress of work. the effects of mixing ratio of the milled powder on sintered and Cu-infiltrated properties of sintered valve seats have been studied. The resultant radial crushing strength and hardness of sintered specimens were gradually increased with increasement of volume of milled powders. It is because increasement of sintering density by increasing of surface diffusion. The hardness of Cu-infiltrated specimens became lower than that of the commercial powders as the increasement of volume of milled powders. It was due to the decrease of the amount of the martensite. By results of this research, It has been found that martensite is formed around of the Cu-infiltrated site and the decrease of the amount of the martensite is due to decrease of the amount of the Cu-infiltrated site by the decrease of gas channel.
Two kinds of Bi2Te3 powders, pure Bi2Te3/2vol.%ZrO2, have been prepared by a mechanical grinding process process. Effect of mixing of the powders on thermoelectric of the sintered body has been investigated by measuring Seebeck Coeffcient, specific electric resistivity and thermal conductivity. With an increase in the weight fraction of the Bi2Te3/2vol.%ZrO2 powder from 0 to 40wt.%. Especially, the figure of merit of the mixedBi2Te3 sintered body increases and thereafter dedreases above 40wt.%. Especially. the figure of merit of the mixed Bi2Te3 sintered bodies with mixing of Bi2Te3/2vol.%ZrO2 powder increased about 1.3time in comparison with the value of the specimen before mixing. Mixing of two kinds of Bi2Te3 powders which have different theramal and electric propertries with each other seemed to be useful methob to increase the figure of merit of Bi2Te3 sintered body.
Different sizes of Si powder and milling medium materials (steel and partially stabilized zirconia (PSZ)) were used to synthesize and by mechanical aollying (MA) of Ti-25.0.at.%Si and Ti-66.7at.% Si powder mixtures. the formation of each titanium silicide did not occur even after 360 min of MA of as-re-ceived Si and Ti powder mixtures due to the lack of homogeneity. , however, was synthesized after 240 min of MA of Ti and 60 min-premilled Si powder mixture. and were produced by jar milling of Ti and 60 min-premilled Si powder mixture for 48 hr and high -energy PSZ ball-milling in a steel vial for 360 min. The formation of each titanium silicide was characterized by a slow reaction rate as the reactants and product(s) coexisted for a certain period of time. The formation of and and the reaction rates appeared to be influenced by the Si particle size, the homogeneity of the powder mixtures and the milling medium materials.
본 논문은 콘크리트 배합 방식(NMA, TSMA1, TSMA2)에 따른 순환 굵은골재 치환량에 따른 콘크리트의 기계적 성능을 비교 평가 하였다. 실험은 순환 굵은골재를 0%, 50%, 100%로 3수준으로 콘크리트의 배합 방식에 따라 실험을 진행하였다. 굳지 않은 콘크리트에서는 공기량, 슬럼프, 단위용적질량 실험을 진행하였으며, 경화 콘크리트에서는 압축강도 및 휨강도 시험을 진행하였다. 본 연구의 실험결과 NMA 방식과 비교하여 TSMA 방식에서 강도 저하가 나타나고 있음을 확인할 수 있었다. 하지만, 이는 순환 굵은골재가 다량 치환됨에 따른 것으로 사료된다. 순환 굵은골재가 다량 치환됨에 따라 슬럼프 증진, 공기량 증진, 강도 저하가 나타남을 확인하였다.
This study was performed mechanical properties of porous concrete according to fiber mixing conditions. As the results of study, When considering the void ratio, compressive and flexural strength of porous concrete, the proper type and content of fiber is thought to be PVA 0.05%.