Heavy metal pollution has a harmful impact on human health and is regarded as a vital problem. Preparation of a novel, low cost bio-sorbent for heavy metal sorption is the main target of this research. Non-living Chlorella Vulgaris Alga/Date pit activated carbon composite (1:1), (CV/AC), is a novel bio-sorbent prepared by the wet-chemical method for sorption of Pb (II) and Sr (II) from aqueous media. The optimum pH for sorption reaction is 5 and the equilibrium time is achieved within 1 h. The sorption efficiencies are 90.5% for Pb(II) and 95.7% for Sr(II) with initial concentration Co 10 mg L– 1 at 298 K. The monolayer sorption capacities of CV/AC composite at 298 K and pH = 5 were 6.34 ± 0.059, 5.97 ± 0.22 mg g– 1. The saturation capacities were 98.5 and 125 mg g– 1 for Pb (II) and Sr (II), respectively after 10 days. The sorption process is a spontaneous and endothermic reaction. It follows a pseudo-2nd-order mechanism. The results are suggestive of the need to adopt CV/AC composite as a potential bio-sorbent of Pb (II) and Sr (II) for waste water treatment.

Amine-functionalized graphene was synthesized via a one-step solvothermal method and used as a metal-free cathode for non-aqueous lithium–oxygen batteries. The material delivered an outstanding specific capacity of 19,789 mAh/g at a current density of 200 mA/g as well as better cycling stability than graphene without the amine functional group. This improvement was attributed to the electron-donating effect of the amine groups and appropriate mesopore volume, which can promote the penetration of oxygen, electrons, and lithium ions, as well as accommodate more discharge products, Li2O2 in Li–O2 batteries. Amine-functionalized graphene has an amine functional group on the carbon surface, which improves the electrical conductivity of carbon and provides electrochemical active sites for oxygen absorption reactions.

High-level heteroatom, N and S, dual-doped graphene with an improved mesoporous structure was fabricated via facile in situ carbonization and used as metal-free cathode for non-aqueous lithium oxygen batteries. The prepared cathode delivered an ultrahigh specific capacity of 22,252 mAh/g at a current density of 200 mA/g as well as better cycling reversibility because of the larger and copious mesopores, which can promote the penetration of oxygen, electrons, and lithium ions and the ability to accommodate more discharge products, e.g., Li2O2, in Li–O2 batteries. The material had a high level of heteroatom co-doping in the carbon lattice, which enhanced the electrical conductivity and served as active sites for the oxygen reduction reaction.

Al2O3 nanosol dispersed under ethanol or N-Methyl-2-pyrrolidone(NMP) was studied and optimized with various dispersion factors and by utilizing the silane modification method. The two kinds of Al2O3 powders used were prepared by thermal decomposition method from aluminum ammonium sulfate(AlNH4(SO4)2) while controlling the calcination temperature. Al2O3 sol was prepared under ethanol solvent by using a batch-type bead mill. The dispersion properties of the Al2O3 sol have a close relationship to the dispersion factors such as the pH, the amount of acid additive(nitric acid, acetic acid), the milling time, and the size and combination of zirconia beads. Especially, Al2O3 sol added 4 wt% acetic acid was found to maintain the dispersion stability while its solid concentration increased to 15 wt%, this stability maintenance was the result of the electrostatic and steric repulsion of acetic acid molecules adsorbed on the surface of the Al2O3 particles. In order to observe the dispersion property of Al2O3 sol under NMP solvent, Al2O3 sol dispersed under ethanol solvent was modified and solventexchanged with N-Phenyl-(3-aminopropyl)trimethoxy silane(APTMS) through a binary solvent system. Characterization of the Al2O3 powder and the nanosol was observed by XRD, SEM, ICP, FT-IR, TGA, Particles size analysis, etc.

Li metal is accepted as a good counter electrode for electrochemical impedance spectroscopy (EIS) as the active material in Li-ion and Li-ion polymer batteries. We examined the existence of signal noise from a Li-metal counter quantitatively as a preliminary study. We suggest an electrochemical cell with one switchable electrode to obtain the exact impedance signal of active materials. To verify the effectiveness of the switchable electrode, EIS measurements of the solid electrolyte interphase (SEI) before severe Li+ intercalation to SFG6 graphite (at 〉 ca. 0.25 V vs. Li/Li+) were taken. As a result, the EIS spectra without the signal of Li metal were obtained and analyzed successfully for the following parameters i) Li+ conduction in the electrolyte, ii) the geometric resistance and constant phase element of the electrode (insensitive to the voltage), iii) the interfacial behavior of the SEI related to the Li+ transfer and residence throughout the near-surface (sensitive to voltage), and iv) the term reflecting the differential limiting capacitance of Li+ in the graphite lattice.

비대칭 폴리비닐리덴플루오라이드(PVDF) 막을 상전환법으로 제조하였다. 도포용액은 PVDF를 용매인 N-ethyl-2-pyrrolidone (NMP)와 비용매인 1,4-dioxane, diethyleneglycol dimethyl ether (DGDE), acetone, (equation omitted)-butyrolactone(GBL)의 혼합용매에 녹여서 제조한다. 여러 첨가제가 도포용액 특성, 투과특성과 막 구조에 미치는 영향을 조사하였다. 응고제인 물과 1,4-dioxane, DGDE, acetone과의 상용성이 NMP보다 낮아서 기공크기가 작아진다. 첨가제의 양을 조절하여 기공크기를 변화시켰다. 혼합용매(수계 및 비수계)가 막의 투과성능에 미치는 영향을 살펴보았다. 용액점도뿐만 아니라 표면장력도 용매 투과특성에 영향을 끼침을 알 수 있었다.

This study showed that the optimized cleaning process using non-aqueous cleaning solvents is adaptable in the industrial field for existing 1.1.1-TCE cleaning solvents which is an ozone depleting sustance. Alternative cleaning solvent system substituted for existing cleaning solvent against non-aqueous pollutants(cutting & flux oil), was evaluated for the cleaning efficiency using gravimetric analysis method and surface change of sample by Image analyzer. The results showed that alternative solvents and process had excellent cleaning efficiency.