서로 다른 술폰화 정도에 따라 sulfonated star branched poly(styrene-b-butadiene-b-styrene) triblock copolymer (SSBS)가 합성되었다. 술폰화된 butadiene block은 FT-IR spectroscopy로 확인할 수 있다. 술폰화 정도를 측정 비교하기 위해 서 산-염기 적정을 통하여, ion exchange capacity (IEC)를 계산하였다. 술폰화된 SSEB 전해질막은 높은 water uptake와 proton conductivity를 보였다. 실온에서 25 mol% 술폰화된 SSBS는 0.114 S/cm라는 높은 값을 나타냈으며, 이는 Nafion과 비슷 한 수치였다. 일정한 상대 습도에서 온도의 증가는 현저하게 높은 수소이온전도도를 나타냄을 알 수 있었다. 모든 술폰화된 막 은 Nafion과 비교했을 때 낮은 methanol 투과도를 보여주었다. AFM을 이용하여 술폰화된 전해질막의 구조는 이른바 분리된 나 노구조의 미세상과 ionic channel의 접속으로 이루어졌음을 확인할 수 있었다.

In the present work, a comparative study of the mechanical behavior of two series of elastomeric composites, based on carboxylated styrene butadiene rubber (X-SBR) and reinforced with rice bran carbon (RBC) and graphite, is reported. Hybrid composites of X-SBR filled with RBC-graphite were also investigated in terms of the cure characteristics, hardness, tensile properties, abrasion resistance, and swelling. It was observed that the cure times decreased with the incorporation of a carbon filler whereas the torque difference, tensile strength, tensile modulus, hardness, and swelling resistance increased compared to the neat X-SBR revealing a favorable characteristic of crosslinking. Dynamic rheological analysis showed that the G' values of the composites, upon the addition of RBC-graphite, were changed to some extent. This demonstrates that the presence of a strongly developed network of fillers will ensure a reinforcing characteristic in a polymer matrix.

PURPOSES: The study objective was to evaluate rheology and physical properties of SBS-modified warm-mix asphalt (WMA) binders in comparison with hot-mix asphalt (HMA) binders. METHODS : Four different SBS polymers were used to prepare polymer-modified asphalt (PMA) binders, and three different warm-mix additives (WAD) were used to prepare a total of 12 WMA PMA binders. The kinematic viscosity was measured at 115, 135℃. The PG was determined using DSR and BBR. The pass/fail (P/F) temperatures for high and low PG grading were evaluated for HMA PMA and WMA PMA binders. RESULTS: PG 76-22 binders could be prepared by modifying the base binder (PG 64-22) using 4.5 wt% of SBS. The kinematic viscosity (KV) of SBS PMA was increased by 3 times higher than that of base asphalt. The SBS PMA with WAD showed 10% lower KV than that of the normal SBS PMA at 115℃ The high P/F temperatures showed almost no difference between HMA PMA and WMA PMA binders. The high P/F temperature showed very high correlations with KV (R2 > 0.97). The result of SBS modification caused increase of low P/F temperature by 2.7℃ on average. CONCLUSIONS : Since the PMA with WAD showed 10% lower KV than normal (HMA) PMA at 115℃, reducing PMA mixture temperature down to a WMA level was possible in this study. The higher KV binders showed the higher P/F temperature. There was almost no change in high P/F temperature due to the use of WAD. The SBS PMA, showing an increased low P/F temperature, might show somewhat poorer performance at low-temperature, even though the lower PG grade was staying at the same level, i.e., -22℃.

The characteristics of all polymer composites containing carbon materials are determined by four factors: component properties, composition, structure and interfacial interactions. The most important filler characteristics are particle size, size distribution, specific surface area and particle shape. As a consequence, in this paper we discuss the aspects of the mechanical, electrical and thermal properties of composites with different fillers of carbon black, carbon nanotube (CNT), graphene and graphite and focus on the relationship between factors and properties, as mentioned above. Accordingly, we fabricate rubber composites that contain various carbon materials in carbon black-based and silica based-SBR matrixes with dual phase fillers and use scanning electron microscopy, Raman spectroscopy, a rhometer, an Instron tensile machine, and a thermal conductivity analyzer to evaluate composites' mechanical, fatigue, thermal, and electronic properties. In mechanical properties, hardness and 300%-modulus of graphene-composite are sharply increased in all cases due to the larger specific surface. Also, it has been found that the thermal conductivity of the CNT-composite is higher than that of any of the other composites and that the composite with graphene has the best electrical properties.

We investigated the effect of diameter and content of carbon nanotubes (CNTs) on the physical properties of styrenebutadiene rubber (SBR)/CNTs nanocomposites. CNTs-reinforced SBR nanocomposites were prepared by the melt mixing process. CNTs with different diameters were synthesized by the chemical vapor deposition method (CVD). In this work, the mechanical property and other physical properties of SBR/CNTS nanocomposites were discussed as a function of the content and diameter of CNTs.

본 연구에서는 SEBS와 여러 가지의 유기화물로 처리된 MMT (montmorillonite) type의 clay를 이용하여 SEBS-clay 하이브리드 막을 용융삽입법으로 제조하였다. clay의 함량은 5 phr (per hundred resin)로 고정하였다. internal mixer를 사용하여 clay를 SEBS에 분산시켰으며, 제조된 SEBS-clay 하이브리드에서 clay의 특성피크가 완전히 박리되거나 이동하는 XRD 결과로부터 clay의 층간거리가 넓어지는 고분자의 clay 층간삽입을 확인하였다. Clay의 종류에 따라서 제조된 SEBS-clay 하이브리드 막의 가스투과도, 기계적 물성 및 열적 성질을 측정하였다. SEBS-clay 하이브리드 막은 clay 자체의 도입과 층간거리의 확대로 기체분자의 tortuosity를 증가시켜서 가스투과도를 저하시키는 것을 확인하였다.

To investigate organoclay, high styrene resin masterbatch (HSR), high impact polystyrene (HIPS), and polystyrene (PS) as reinforcing materials for the improvement of the abrasion resistance of poly(styrene-block-butadiene-block- styrene) (SBS), SBS/organoclay nanocomposites, SBS/HSR, SBS/HIPS, and SBS/PS blends were prepared. The effect of organoclay and blends on the abrasion resistance and mechanical properties of SBS was investigated. Even though intercalations of organoclay are observed for SBS/Cloisite 20A nanocomposites and not for SBS/Cloisite 30B composites, the abrasion resistance of SBS/Cloisite 20A nanocomposites is worse than that of SBS/Cloisite 30B composites. When SBS was blended with HSR, HIPS and PS, the abrasion resistance of the blends increases with increasing of HSR, HIPS and PS content from 0 to 20 wt%.