In this study, a finite element analysis approach is proposed to predict the fluid-structure interaction behavior of active materials for lithium-ion batteries (LIBs), which are mainly composed of graphite powder. The porous matrix of graphite powder saturated with fluid electrolyte is considered a representative volume element (RVE) model. Three different RVE models are proposed to consider the uncertainty of the powder shape and the porosity. Pwave modulus from RVE solutions are analyzed based on the microstructure and the interaction between the fluid and the graphite powder matrix. From the results, it is found that the large surface area of the active material results in low mechanical properties of LIB, which leads to poor structural durability when subjected to dynamic loads. The results obtained in this study provide useful information for predicting the mechanical safety of a battery pack.

경주 방사성폐기물 처분시설은 향후 80만 포장물을 처분할 계획이며 다양한 처분방식 및 관리형태를 가진 복합계가 될 것 이다. 본 논문에서는 전체부지 처분용량(80만 포장물) 처분시설의 단계별 개발에 따른 영향을 평가하기 위하여 처분시설 종 합개발계획(안)에 따른 예비안전성평가를 수행하였다. 각 시나리오에 대한 안전성평가결과 처분시설의 성능목표치를 만족 하였다. 다만, 전체처분시설의 안전성 평가결과에 중준위 방사성폐기물로 인하여 1단계 동굴 처분시설이 가장 크게 영향을 미치므로 처분시설의 안전성 향상을 위하여 처분방사능량제한 설정 등 관리방안이 필요하다. Safety Case 단계별 구축을 통 하여 중·저준위 방사성폐기물 처분시설 종합개발 과정에서 인지된 불확실성을 저감하여 안전성을 증진 시킬 수 있을 것으 로 판단된다.

For useful research animal to study human’s disease and for xenotransplantation donor, pig was studied to improve the quality of in vitro production (IVP). But, still the developmental ability of in vitro porcine embryos is still lower than in vivo embryos. Using a antioxidant is one of the strategy to overcome the drawback of in vitro producted embryos by protecting the oocyte from free radicals during in vitro maturation (IVM). Resveratrol, one of the plant-derived polyphenol antioxidants, have been used as effective antioxidants. Therefore, resveratrol treatment during IVM of porcine oocytes is expected to improve efficiency of the IVP by reducing free radical accumulation. In this study, we designed control (no treated) and resveratrol treatment groups (0, 2 and 4uM), evaluated maturation rate, cleavage rate, blastocyst formation rate and total cell number. Additionally GSH and ROS accumulation levels were measured via staining oocytes. In the results, maturation rate had not shown significant difference among the groups. However, in further development, not only the results of cleavage rate (0uM : 84.64±2.65 vs 4uM : 93.67±2.36, p<0.05) and blastocyst formation rate (0uM : 6.39± 0.90, vs 4uM : 13.67±2.32, P<0.05) were significantly increased in 4uM resveratrol treated group, and result of total cell number (0uM : 22.47±0.76 vs 2, 4uM : 30.35±1.76, 27.65±1.23, P<0.05) also shown significant difference in 2, 4uM resveratrol groups with control. GSH accumulated levels of matured oocytes in resvetrol treated groups were significantly higher than control. Meanwhile ROS levels of treated groups were significantly reduced [GSH (0uM : 142±10.49 vs 2, 4uM : 163.2±3.29, 169.7±0.94, P<0.05), ROS (0uM : 170.2±7.76 vs 2, 4uM : 118.6±7.90, 130±7.07, P<0.05)]. From these results, we conclude the treatment of resveratol improved further development of porcine embryos by regulating intracellular GSH, ROS levels during porcine IVM. Therefore, exogenous antioxidants such as a resveratol can be supportive substances for obtaining the improved quality of IVP.

Euzophera batangensis (Lepidotera: Pyralidae) is seriously damaging trunks or branches of persimmon tree (Diospyros sp.). We tested the attractiveness of (Z)-9-tetradecen-1-ol (Z9-14OH) and (Z9,E12)-tetradeca- 9,12-dien-1-ol (Z9,E12-14OH) with single or blended baits at southern parts of Korea in 2014 and 2015. The monoene was not attractive at all at three places during the two years. In 2014, diene was equally or more attractive than the mixture in Jinju and Suncheon, respectively. In 2015 too, the attractiveness of diene and mixture was not different in Jinju and Munsan. Monitoring of the seasonal occurrence of E. batangesis with the sex pheromone components revealed that it occurred three times a year; the first occurrence from early April to mid May, the second from early Jun to mid July, and the third from late August to late September.

The purpose of this study is to present theoretical and experimental evidence for a niche strategy for small and medium online shopping malls to run business against large famous shopping malls prevailing the E-commerce market. For this, the present study demonstrates how chronic construal levels of consumers may affect their alternative choice for online shopping via various contexts (Experiment 1-3) and categories (Experiment 3-5). This series of experiments suggests that consumers with high construal level can be defined as a group that is relatively less susceptible to reputation of the shopping malls. Thus, strategically targeting this group of consumers will help small and medium-sized online malls lacking store reputation to mitigate their competitive disadvantage. Based on both existing literature and the experimental results as above, this research discusses possible methods for small and medium-sized online shopping malls to target high-construal segmentation.

The squid Todarodes pacificus is a commercially important fishery species in East Asia. As East Asians consume raw or lightly cooked squids, there has been growing concern about parasitic infections associated with squid consumption. In the current study, five squids caught in the East Sea were sampled for parasitological research from the biggest fishery market in Seoul, Republic of Korea. They were dissected and examined for parasites using a light microscope. Proteocephalus sp. was isolated and identified using field emission scanning electron microscopy, PCR, and sequencing. Given that Proteocephalus spp. can be affected by water temperature and geographical characteristics, further research on Proteocephalus spp. with respect to changes in water temperature in the East Sea is important.

Graphene was grown on molybdenum (Mo) foil by a chemical vapor deposition method at different growth temperatures (1000°C, 1100°C, and 1200°C). The properties of graphene were investigated by X-ray diffraction (XRD), X-ray photoelectron spectroscopy, and Raman spectroscopy. The results showed that the quality of the deposited graphene layer was affected by the growth temperature. XRD results showed the presence of a carbide phase on the Mo surface; the presence of carbide was more intense at 1200°C. Additionally, a higher I2D/IG ratio (0.418) was observed at 1200°C, which implies that there are fewer graphene layers at this temperature. The lowest ID/IG ratio (0.908) for the graphene layers was obtained at 1200°C, suggesting that graphene had fewer defects at this temperature. The size of the graphene domains was also calculated. We found that by increasing the growth temperature, the graphene domain size also increased.

Oxalic acid has a nematicidal activity against the root-knot nematode Meloidogyne incognita. High producer of oxalic acid was isolated, and then named as Aspergillus niger F22. Oxalic acid production was investigated under various temperatures from 20 – 33oC and rotational speeds in 5 L jar fermenters. Yield of oxalic acid increased with decreasing temperature. The highest yield was obtained at 23oC, showing the yield of oxalic acid of 8.7 g/L, whereas oxalic acid production was least at 33oC. At 20oC, the yield was lower than that of 23oC. At a rotational speed of 300 rpm, serious oxygen depletion was present from 48 - 72 h, resulting in low productivity of 26.2 mg /L·h. When a rotational speed was set at 600 rpm, dissolved oxygen tension was over 40% and oxalic acid production increased up to approximately 55%. Viscosity during the culture differed with temperatures. Viscosity increased with the increment of temperatures. When A. niger F22 was cultured at 23oC, viscosity was 810 cP, which was favorable for oxalic acid production.

Powder injection molding (PIM), which combines the advantages of powder metallurgy and plastic injection molding technologies, has become one of the most efficient methods for the net-shape production of both metal and ceramic components. In this work, plasma display panel glass bodies are prepared by the PIM process. After sintering, the hot isostatic pressing (HIP) process is adopted for improving the density and mechanical properties of the PIMed glass bodies. The mechanical and thermal behaviors of the prepared specimens are analyzed through bending tests and dilatometric analysis, respectively. After HIPing, the flexural strength of the prepared glass body reaches up to 92.17 MPa, which is 1.273 and 2.178 times that of the fused glass body and PIMed bodies, respectively. Moreover, a thermal expansion coefficient of 7.816 × 10−6/oC is obtained, which coincides with that of the raw glass powder (7.5-8.0 × 10−6/oC), indicating that the glass body is fully densified after the HIP process.

The sintering mechanisms of nanoscale copper powders have been investigated. A molecular dynamics (MD) simulation with the embedded-atom method (EAM) was employed for these simulations. The dimensional changes for initial-stage sintering such as characteristic lengths, neck growth, and neck angle were calculated to understand the densification behavior of copper nano-powders. Factors affecting sintering such as the temperature, powder size, and crystalline misalignment between adjacent powders have also been studied. These results could provide information of setting the processing cycles and material designs applicable to nano-powders. In addition, it is expected that MD simulation will be a foundation for the multi-scale modeling in sintering process.

This research was conducted in order to understand the hybridization between Quercus aliena Blume and Q. serrata Murray in Korea which show wide range of morphological variations within species and interspecific variations of diverse overlapping characteristics caused by hybridization. Morphological analysis (principal components analysis; PCA) of 116 individuals representing two species and their intermediates were performed. As a result, two species were clearly distinguished in terms of morphology, and intermediate morpho-types assumed to be hybrids between the two species were mostly located in the middle of each parent species in the plot of the principal components analysis. There was a clear distinction between two species in trichome distribution pattern which is an important diagnostic character in taxonomy of genus Quercus, whereas intermediate morpho-types showed intermediate state between two species’ trichome distributions. Forty-two individuals representing two species and their intermediates were examined for leaf flavonoid constituents. Twenty-three flavonoid compounds were isolated and identified: They were glycosylated derivatives of flavonols, kaempferol, quercetin, isorhamnetin and myricetin. The flavonoid constituents of Q. aliena were five glycosylated derivatives: kaempferol 3-O-galactoside, kaempferol 3-O-glucoside, quercetin 3-O-galactoside, quercetin 3-O-glucoside, and Isorhamnetin 3-O-glucoside. The flavonoid constituents of Q. serrata had 20 diverse flavonol compounds including five flavonoid compounds found in Q. aliena. It was found that there is a clear difference in flavonoid constituents of Q. aliena and Q. serrata. Flavonoid chemistry is very useful in recognizing each species and putative hybrids. The flavonoid constituents of intermediates were a mixture of the two species’ constituents and they generally showed similar characteristics to morpho-types. The hybrids between Q. aliena and Q. serrata showed morphologically and chemically diverse characteristics and it is assumed that there are frequent interspecific hybridization and introgression.

Powder injection molding is an important manufacturing technology to mass produce superalloy components with complex shape. Injection molding step is particularly important for realizing a desired shape, which requires much time and efforts finding the optimum process condition. Therefore computer aided engineering can be very useful to find proper injection molding conditions. In this study, we have conducted a finite element method based simulation for the spiral mold test of superalloy feedstock and compared the results with experimental ones. Sensitivity analysis with both of simulation and experiment reveals that the melt temperature of superalloy feedstock is the most important factor for the full filling of mold cavity. The FEM based simulation matches well the experimental results. This study contributes to the optimization of superalloy powder injection molding process.

To compensate for the critical shortage of human organs for allotransplantation, xenotransplantation studies using genetically modified pigs are being performed in Korea. Two types of pigs that are used are α1,3-galactosyltransferase gene knockout (GalT KO) pigs and GalT KO+hCD46 (human complement regulatory protein) pigs. The present study measured the gestation time, birth weight, daily growth rate, and heart weight of both kinds of transgenic minipigs. The gestation period for both types of pigs was 117∼119 days. There was no difference in the body weight of GalT KO (—/+) and GalT KO (—/—) piglets, but GalT KO+hCD46 (—hCD46+/+) pigs were significantly heavier at birth than were GalT KO+hCD46 (—hCD46+/—hCD46+) pigs. During the first 10 weeks of life, the daily weight gain of GalT KO+hCD46 (—hCD46+/—CD46+) piglets, which are considered the optimal type for xenotransplantation, was 0.19 kg. The weight of hearts from GalT KO piglets up to two months of age was affected more by body weight than by age. Transgenic pigs showed no differences in gestation period or reproductive ability compared with normal pigs. These results comprise basic data that may be used in xenotransplantation studies and transgenic animal production in Korea.

This study investigated the densification behavior of rhenium alloys including W-25 wt.%Re and Re-2W-1Ta (pure Re) during sintering. The dilatometry experiments were carried out to obtain the in-situ shrinkage in H2 atmo-sphere. The measured data was analyzed through shrinkage, strain rate and relative density, and then symmetricallytreated to construct the linearized form of master sintering curve (MSC) and MSC as a well-known and straightforwardapproach to describe the densification behavior during sintering. The densification behaviors for each material were ana-lyzed in many respects including apparent activation energy, densification parameter, and densification ratio. MSC witha minimal set of preliminary experiments can make the densification behavior to be characterized and predicted as wellas provide guideline to sinter cycle design. Considering the results of linearized form and MSC, it was confirmed thatthe W-25 wt.%Re compared to Pure Re is more easily densified at the relatively low temperature.

The purpose of this study was to determine the effectiveness of sit-to-stand training on unstable surfaces in individuals with stroke. Nineteen subjects with chronic stroke were divided into two groups: an experimental group (10 subjects) and a control group (9 subjects). They received 30 minutes of Neuro-developmental therapy (NDT) treatment, and sit-to-stand exercise for 15 minutes three times a week for four weeks. During the sit-to-stand training, the experimental group performed on an unstable AIREX balance pad, but the control group performed on a stable surface. Balance ability and weight-bearing distribution during quiet standing were measured before and after training period using the 7-item Berg balance scale-3P (BBS-3P) and the Five-times-sit-to-stand test (FTSST). In addition, the muscle strength of the knee extensor was evaluated before and after the training period. The results were as follows: 1) The weight-bearing distribution forward of the affected leg, increased significantly in the experimental group after the four-week intervention (p<.05), 2) The 7-item BBS-3P and FTSST increased significantly in the experimental group after the four-week intervention (p<.05), 3) The knee extensor muscle strength in both groups increased significantly after the four-week intervention (p<.05). In conclusion, the results of this study did not show that the sit-to-stand training on an unstable surface was more effective than on a stable surface. However, the results suggested that sit-to-stand training is effective in the balance training of stroke patients.