WO3-doped SnO2 thin films were prepared in a solution-deposition method and their gas-sensing characteristics were investigated. The doping of WO3 to SnO2 increased the response (Ra/Rg, Ra: resistance in air, Rg: resistance in gas) to H2 substantially. Moreover, the Ra/Rg value of 10 ppm CO increased to 5.65, whereas that of NO2 did not change by a significant amount. The enhanced response to H2 and the selective detection of CO in the presence of NO2 were explained in relation to the change in the surface reaction by the addition of WO3. The WO3-doped SnO2 sensor can be used with the application of a H2 sensor for vehicles that utilize fuel cells and as an air quality sensor to detect CO-containing exhaust gases emitted from gasoline engines.

A new cost-effective atomic layer deposition (ALD) technique, known as Proximity-Scan ALD (PS-ALD) was developed and its benefits were demonstrated by depositing Al2O3 and HfO2 thin films using TMA and TEMAHf, respectively, as precursors. The system is consisted of two separate injectors for precursors and reactants that are placed near a heated substrate at a proximity of less than 1 cm. The bell-shaped injector chamber separated but close to the substrate forms a local chamber, maintaining higher pressure compared to the rest of chamber. Therefore, a system configuration with a rotating substrate gives the typical sequential deposition process of ALD under a continuous source flow without the need for gas switching. As the pressure required for the deposition is achieved in a small local volume, the need for an expensive metal organic (MO) source is reduced by a factor of approximately 100 concerning the volume ratio of local to total chambers. Under an optimized deposition condition, the deposition rates of Al2O3 and HfO2 were 1.3 Å/cycle and 0.75 Å/cycle, respectively, with dielectric constants of 9.4 and 23. A relatively short cycle time (5~10 sec) due to the lack of the time-consuming "purging and pumping" process and the capability of multi-wafer processing of the proposed technology offer a very high through-put in addition to a lower cost.

The effects of the deposition and annealing temperature on the structural, electrical and opticalproperties of Ag doped ZnO (ZnO:Ag) thin films were investigated. All of the films were deposited with a 2wt%Ag2O-doped ZnO target using an e-beam evaporator. The substrate temperature varied from room temperature(RT) to 250oC. An undoped ZnO thin film was also fabricated at 150oC as a reference. The as-grown films wereannealed in temperatures ranging from 350 to 650oC for 5h in air. The Ag content in the film decreased asthe deposition and the post-annealing temperature increased due to the evaporation of the Ag in the film.During the annealing process, grain growth occurred, as confirmed from XRD and SEM results. The as-grownfilm deposited at RT showed n-type conduction; however, the films deposited at higher temperatures showedp-type conduction. The films fabricated at 150oC revealed the highest hole concentration of 3.98×1019cm-3 anda resistivity of 0.347Ω·cm. The RT PL spectra of the as-grown ZnO:Ag films exhibited very weak emissionintensity compared to undoped ZnO; moreover, the emission intensities became stronger as the annealingtemperature increased with two main emission bands of near band-edge UV and defect-related greenluminescence exhibited. The film deposited at 150oC and annealed at 350oC exhibited the lowest value of Ivis/Iuv of 0.05.

The ferroelectric properties of UV irradiated and non-irradiated PZT films prepared via photochemical metal-organic deposition using photosensitive precursors were characterized. Fourier transform infrared spectroscopy showed that complete removal of organic groups was possible through UV exposure of the spin-coated PZT precursor films at room temperature. The measured remnant polarization values of UV-irradiated and non-irradiated PZT films after annealing at 650˚C were 29 and 23 μC/cm2, respectively. The UV irradiation was found to be effective for the enhancement of the<111> growth orientation and ferroelectric property of PZT film and in the direct patterning in the fabrication of micro-patterned systems without dry etching.

본 논문에서는 고준위폐기물 처분용기를 지하 심지층에 처분하기 위하여 요구되는 구조설계 요구조건과 구조안전성 평가 기준을 도출하였다. 고준위폐기물은 높은 열과 많은 방사능을 방출하기 때문에 고준위폐기물을 넣어 보관하는 처분용기는 그 취급에 많은 주의가 요구된다. 이를 위하여 고준위폐기물 처분용기는 장기간(보통 10,000년 동안) 안전한 장소에 보관되어야 한다. 보통 이 보관 장소는 지하 500m에 위치한다. 지하 깊은 화강암에 고준위폐기물을 보관하도록 설계되는 처분용기는 내부주철삽입물과 이를 감싸고 있는 부식에 강한 와곽쉘, 위 덮개와 아래 덮개로 구성되는 구조로 되어 있으며 지하수압과 벤토나이트 버퍼의 팽윤압을 받는다. 따라서 고준위폐기물 처분용기는 심지층에 보관 시 이들 외력들을 견디도록 설계되어야 한다. 만약에 발생 가능한 모든 하중조합을 고려한 처분용기 설계가 되지 않으면 심지층에 위험한 고준위폐기물 처분 시에 처분용기에 소성변형이나 크랙 또 좌굴같은 구조적 결함이 발생할 수 있다. 따라서 심지층에 처분용기를 처분 시에 처분용기에 발생하는 구조적 문제들이 발생하지 않게 하기 위하여 여러 가지 구조해석이 수행되어야 한다. 이러한 구조해석 수행에 앞서 처분용기 설계 타당성을 평가하기 위한 기준이 필요하다. 또한 평가기준에 영향을 미치는 설계요구조건(설계변수)이 명확히 검토되어야 한다. 따라서 본 논문에서는 처분용기의 구조설계 요구조건(설계변수)과 구조 안전성 평가기준을 도출하고자 한다.

고준위폐기물을 지하 500m의 화강암 암반의 처분장에 장기간(약 10,000년 동안) 처분 시 폐기물에서 발생하는 열에 의하여 처분용기 및 처분용기를 감싸고 있는 주위 구조물(벤토나이트 버퍼, 암반 등)의 처분시간 경과에 따른 온포분포 변화를 알아내는 것은 처분장 설계를 위하여 매우 중요하다. 본 논문에서는 수치해석기법을 이용하여 고준위폐기물에서 발생하는 열에 의한 처분용기 및 벤토나이트 버퍼, 처분동굴을 포함하는 복합구조물의 온도분포 변화를 구하였다. 특히 처분 후 500년의 처분시간 경과에 따른 복합구조물의 온도분포 해석을 수행하여 온도분포 변화를 구하였다. 시간에 따른 온도분포 변화에 대한 해석결과를 분석한 결과 처분장 각 구성부분별로 차이는 있으나 처분초기부터 구성부분별로 각각 다르게 온도가 증가하는데 가장 늦은 부분은 150년까지 완만하게 온도가 증가하다가 그 이후에는 온도가 서서히 감소하는 것으로 나타났다.

[ ]의 토양침적으로 인한 농작물 오염 평가를 위한 동적격실모델이 제시되었다 토양침투(percolation), 쟁기질에 의한 토양혼합(soil mixing), 뿌리흡수(plant uptake), 용출(leaching to a deep soil), 토양고착(fixation to a clay mineral)이 모델에서 고려된 의 주요 이동경로이며 의 토양이동에 대한 토양특성(pH, 점토함량, 유기물함량, 이온교환성 K 농도)의 영향을 반영하기 위하여 Absalom 모델을 적용하였다. 모델의 검증을 위해 다른 토양특성을 가진 17종류의 논토양에서 2년 연속 벼를 재배하면서 수행한 모의침적실험으로부터 구한 벼에 대한 전이계수를 모델에 의한 예측치와 비교하였다. 측정된 벼의 전이계수는 pH와 점토함량 변화에는 뚜렷한 경향을 보여주지 않았으나, 유기물함량의 증가 또는 이온교환성 K 농도의 감소에 따라 다소 증가하는 경향을 보여주었다. 측정된 전이계수는 모델에 의한 예측치와 대체적으로 유사한 값을 가졌다.

Particles of high strength material when coated with silver offer a means of obtaining desirable electrical properties and high strength. The coating process employed aqueous ammoniacal silver-nitrate electrolytes with a formaldehyde solution as the reductant. Modifying additives were also applied. The reduction and subsequent deposition of silver occurred selectively on the surface of the tungsten particles. The morphologies of the coated particles were assessed by SEM imaging. The silver was uniformed coated on tungsten powder and its thickness was estimated to be approximately 100nm on the basis of a mass account.

The electrophoretic deposition process of Ni nano-particles was employed for self-repairing of heat exchanger tubes. For electrophoretic deposition of Ni nano-particles on pitted Ni alloy specimen, a constant electric field of 100 V was applied to the specimen for 180 s in Ni-dispersed solution. It was found that as electrophoretic deposition proceeded, the size of the pit remarkably decreased due to the agglomeration of Ni nano-particles at the pit. This strongly suggests that the electrophoretic mobility of the charged particles is larger for the pit with a higher current value rather than outer surfaces with a lower current value.

The coating of conductive polypyrrole (Ppy) on nonconductive ceramic substrates was performed by polymerization of pyrrole (Py) in an aqueous solution. The Ppy film was characterized by scanning electron microscopy and conductivity measurements. Electrophoretic deposition of bimodal alumina suspension prepared with a phosphate ester was performed using Ppy film as a cathode. Fabrication of alumina ceramics with irregular shapes or complicated patterns were also attempted by sintering the deposits together with the Ppy coated substrates in air.

Biomimetic apatite deposition behaviors on Zr-1Nb and Ti-6Al-4V plate with various surface conditions were examined. Both alloys were polished with abrasive papers to have different roughness and some of them were treated in NaOH before exposition in simulated body fluid. NaOH treatment was found to enhance the deposition rate of apatite on Ti-6Al-4V significantly. On the other hand, the deposition rate of Zr-1Nb was not influenced by NaOH treatment. Without NaOH treatment, the polished Zr-1Nb with abrasive paper was found to induce more apatite nucleation than the polished Zr-6Al-4V.

The 21st Century Frontier Program, which is one of the R&D programs funded by Korean government, was launched in 1999 to elevate the status of Korean science and engineering capabilities to the advanced nation in the strategic fields. Currently, 23 different fields of science and engineering programs are carried out by researchers in institutes, universities and industries. Center for Advanced Materials Processing (CAMP) was formulated in 2001 to develop the advanced materials as well as to improve the parts manufacturing process. The main role of CAMP is proposing and forecasting the long term vision in Materials Processing Technology and also supporting the project teams for their best performance in R&D. The CAMP program consists of 5 research areas such as, Multi-layer Ceramic Electronic Parts, Powder Formed Precision Parts, 3 Dimensional Polymer Based Composites, Functional Metal Sheets, Parts Integration Technology. An introduction of R & D activities at CAMP, specially focusing on powder metallurgy, wil be presented.