본 연구는 챗GPT를 대학 교양영어 수업의 학습 도구로 활용하는 효과 적인 수업구성을 하는 것을 목표로 하고 있다. 구체적인 논의는 다음의 네 가지이다. 첫째, 교육계에서 챗GPT 사용에 관해 찬반 논쟁이 있음에 도 불구하고 생성형 AI가 교육계에 큰 변화를 가져올 것이라는 점에는 거의 이견이 없다. 둘째, 챗GPT를 사용함에 있어서 발생 가능한 문제점 을 팩트 체크의 부재, 지적 재산권의 문제, 문해력 저하로 정리하였다. 학습에서 챗GPT를 도구로 사용하기에 앞서서 이러한 문제점들을 학습자 들에게 반드시 인식시키는 교과과정을 만들어야 할 것이다. 셋째, 교육현 장에서 챗GPT를 사용하기 위해서 학습자에게 선제적으로 인식시켜야 할 점은 생성형 AI가 학습의 도구로서의 역할을 하며, 학습자가 인공지능에 의존하는 것이 아니라 인공지능과 협업을 한다는 것이다. 넷째, 학습능력 이 매우 상이한 학생집단을 대상으로 챗GPT를 학습도구로 사용하기 위 해서는 그룹별 협업을 통한 활동이 중요하다. 그룹원들의 다양한 질문을 인공지능에 주입하여 다채로운 결괏값을 얻어 지식을 창조적으로 (재)생 산할 수 있기 때문이다. 본 연구의 의의는 연구에서 제시하는 수업구성 을 실제 수업에 적용하여 또 다른 연구물을 도출할 수 있다는 점이다.

교통량이 증가하고 교량과 같은 특수구조물에 아스팔트 포장이 시공되는 사례가 증가함에 따라 일반적으로 사용되는 아스팔트보다 높은 성능을 가진 아스팔트에 대한 수요가 증가하고 있다. 일반 아스팔트 혼합물은 내구연한이 지나면 재생첨가제 등을 사용하여 다 시 도로포장재료로서 재활용할 수 있는 방안이 마련되어 있으나, 개질 아스팔트가 사용된 폐아스팔트 혼합물은 매립재로 사용하는 것 이외에는 별다른 대안이 없는 실정이다. 이에 본 연구에서는 국토부 지침에 규정된 재활용 아스팔트 혼합물 배합설계법을 적용하여 개질 폐아스팔트 혼합물을 재활용할 수 있는지를 검토해보고자 하였다. 이를 위해 개질 아스팔트를 활용하여 혼합물을 제작하였으며, 현장에서 수거되는 폐아스팔트 혼합물의 노화상태를 모사하기 위해 AASHTO R 30을 참고하여 강제 노화를 실시하였다. 노화 및 추출 과정에서 아스팔트의 물성 변화를 확인하기 위해 절대점도, DSR, MSCR 시험을 실시하였다. 시험결과, 추출 후 바인더의 절대점도는 감소하였으나 G*(복합전단계수)와 δ(위상각)은 증가하는 경향을 보였다. 소성변형 저항성을 확인하기 위해 MSCR(다중 응력 크리프 및 회복) 시험을 실시한 결과,  이 2배 가까이 증가하여 소성변형 저항성이 감소한 것을 확인할 수 있었다. 이러한 결과는 추출시 사용 되는 용매가 개질첨가제를 추출하지 못하여 기인한 결과로 판단된다. 따라서 개질 폐아스팔트 혼합물을 재활용하기 위해서는 기존과 는 다른 별도의 배합설계법이 개발되어야 할 것으로 판단되었다.

연근해에서의 선박 전복사고는 소형 어선에서 많이 발생한다. 소형 어선의 전복사고를 예방하기 위해서는 초기설계 단계에서 부터 복원성을 평가하는 것이 매우 중요하다. 하지만 초기설계 단계에서 확보할 수 있는 정보는 제한적이어서 신뢰성 있는 복원성을 평 가하는 데 어려움이 있다. 이에 본 연구에서는 초기설계 단계에서 추정할 수 있는 KM, KG, 트림을 활용하여 소형 어선의 횡메타센터(GM) 를 추정하고, 표준어선형의 안전성 평가 기준에서 제시된 최소횡메타센터(GMmin)와의 차이를 비교하여 복원성을 평가하는 방안을 제안 하였다. 한국해양안전교통공단에서 제공하는 복원성 평가프로그램인 K-SHIP을 사용한 Hydrostatics 특성 계산에서 요구되는 트림을 도출하 기 위해 상용 CFD 프로그램인 STAR-CCM+를 이용하여 어선 선형에 따른 초기 상태 트림을 추정하였으며, K-SHIP을 사용하여 어선 선형 에 대한 Hydrostatics 특성을 계산하여 GM을 추정하였다. 그리고 GM과 GMmin의 비교를 통해 만재출항상태의 복원성을 비교하였다. 실적 선을 기준선으로 선정하여 본 연구에서 제안한 복원성 평가 방안을 적용해 복원성을 평가하고 그 타당성을 검증하였다. 결과적으로 4.99 톤 어선의 대표적인 선형과 이를 활용해 도출한 모듈 선형 9개의 복원성을 평가하였고, 이중 상대적으로 복원성이 우수한 선형을 선정하 였다.

PURPOSES : The aim of this study is to investigate the enhancement of performance and the mix design method for asphalt mixtures utilizing ferronickel slag, an industrial by-product METHODS : To enhance the performance of FNS asphalt, waste tire powder (CR) was incorporated, and the characteristics of FNS asphalt aggregate, along with the impact of CR, were evaluated through the mix design process. RESULTS : CR is found to be suitable with a size of 30 mesh, and the optimal usage amount is determined to be 1±0.1% of the mixture weight, considering dense grade asphalt mixture. Volumetric design considering the swelling characteristics of CR is necessary, and a mixing design with a consistent tendency can be achieved only when an appropriate VMA is secured. CONCLUSIONS : The mix design for FNS-R asphalt mixture requires an increase of approximately 1% in VMA compared to conventional dense-graded asphalt mixtures to accommodate the swelling of CR. Additionally, FNS-R asphalt exhibits improved resistance to rutting comparable to modified asphalt and meets quality standards, including stripping resistance.

본 논문에서는 역전파 방법 기반 자동미분법을 이용하여 설계민감도를 구하고 이를 응력제한조건을 고려한 위상최적설계에 적용 하였다. 응력제한조건이 있는 위상최적화문제는 특이점(singularity)과 응력의 국부성(local nature of stress constraint)문제, 그리고 설 계 변수에 대한 비선형성의 문제를 포함하고 최적해를 얻기가 매우 힘들다. 특이점 문제를 해결하기 위해서 응력 완화(stress relaxation) 기법을 사용하였고, 응력의 국부성을 해결하기 위해 p-norm을 이용한 전역 응력치를 제한조건에 사용하였다. 설계 변수에 대한 비선 형성을 극복하기 위해 해석적인 방법으로 정확한 설계민감도를 구하는 것이 중요하다. 위상최적설계에서 기존에는 보조변수방법 (adjoint variable method)을 사용하여 빠르고 정확한 설계민감도를 구했지만, 설계민감도를 해석적으로 구해야 하고, 보조평형방정식 을 추가로 풀어야 하는 어려움이 있다. 이를 해결하기 위해서 인공신경망에서 최적 가중치(weights)와 편차(biases)를 구할 때 쓰이는 역전파 기법을 이용하여 설계민감도를 구하고 이를 응력제한조건을 고려한 위상최적설계에 적용하였다. 역전파 기법은 자동미분에 쓰이는 기법으로 목적함수나 제한조건에 대한 설계민감도를 별도의 수식유도 없이 간단하게 구할 수 있는 장점이 있다. 또한, 미분값 을 구하는 역전파의 과정이 보조평형방정식을 푸는 것보다 계산시간이 빠르고 해석적 방법으로 구한 설계민감도와 같은 정확도를 보 여준다

Today, as technology advances and market competition for products intensifies, the product design to improve customer satisfaction by accurately identifying customer needs is emerging as a very important issue for company. Accordingly, the customer-oriented or customer-centered design that maximizes customer satisfaction by grasping and analyzing customer requirements is in the spotlight as an important design theory. In this study, the customer-oriented design is defined as finding the optimal value of design variable with the maximum overall customer satisfaction while minimizing the difference in individual customer satisfaction responded to various customers from multiple product quality characteristics from the perspective of robust design. Therefore, this study presents a new method for modeling the customer preference structure as the different sets of desirability functions for multiple quality characteristics and proposes a new customer-oriented design approach by applying the desirability functions to Taguchi’s robust design process to deal with multi-characteristic design problem. Finally, the proposed method is illustrated with the Kansei engineering design problem of wine glass.

현대 사회가 복잡해지고 기술이 진보하면서 하나의 제품을 설계할 때 단일 특성이 아닌 다 특성을 갖는 제품을 설계하는 것이 요구되고 있다. 다 특성 설계 최적화 문제에서는 설계 변수의 최적값이 특성별로 다르게 되는 현상이 발생하고 이에 따라 하나의 특성에 대한 결과값이 좋아지면 다른 특성에 대한 결과값이 나빠지는 경우에 대해서 trade-off가 필요하다. 따라서 다 특성을 갖는 제품 설계 시 각각의 특성에 대한 성능을 최대화할 수 있는 효율적인 설계 방법의 필요성이 중요한 문제로 떠오르고 있다. 다 특성을 갖는 제품을 설계하는 연구는 오래전부터 중요한 문제로 인식되어 왔는데, 단일 특성에 대해 성능을 최대화하며 강건한 설계를 할 수 있는 다구치 기법과 다기준/다특성 의사 결정 방법인 TOPSIS(Technique for Order of Preference by Similarity to Ideal Solution), GRA(Grey relational analysis), PCA(Principle Component Analysis), Fuzzy Logic System을 통합한 연구들이 진행되어 왔다. 하지만 기존 연구들은 각각의 설계 대안들에 대해 다 특성 결과값에 대한 점수를 통합하여 종합 점수를 비교해 최적의 설계안을 도출할 뿐 설계자의 호감도에 대한 정보는 설계에 반영하지 못한다. 따라서 본 연구에서는 다구치 기법을 기반으로 각각의 특성들에 대한 설계자의 서로 다른 호감도를 함수로써 표현하여 강건성과 함께 설계자의 호감도를 동시에 설계에 반영할 수 있는 방법을 제안한다.

Today, as technology advances and market competition for products intensifies, the design to improve product satisfaction by accurately identifying customer requirements is emerging as a very important problem for company. Accordingly, Customer-Oriented Design, that maximizes customer satisfaction by grasping and analyzing customer requirements, is in the spotlight as an important design theory. In this study, Customer- Oriented Design is defined as finding the optimal value of the design variable with the maximum overall customer satisfaction while minimizing the difference in individual customer satisfaction responded to various customers from multiple product quality characteristics from the perspective of robust design. Therefore, in this work, we present a new method for generating a Desirability Function for each quality characteristic to deal with the multi characteristic parameter design with multiple quality characteristics. And we propose a new Customer-Oriented Design methodology that applies these Desirability Functions to Taguchi’s parameter design process.

Screws are the closest and most familiar mechanical elements of everyday life, and are generally used so widely that there is no machine without screws. Screws are used to make it easier to combine objects with objects, and are also used to transfer large forces from machines. The most influential factor in the coupling of these screws is the effective diameter. If the effective diameter is not accurate, the support cannot be finished or endured, leading to a major accident. The importance of these screws cannot be ignored, so in this study, the effective diameter was measured using the three-wire method, the screw micrometer method, and the projector method, and the one-way factor design method was applied to determine the exact method compared to the KS standard.

Despite the increasing interest in Deep Borehole Disposal (DBD) for its capability of minimizing disposal area, detailed research about DBD operation system design should be conducted before the DBD can be implemented. Recently, DBD operation system applying wireline emplacement (WE) technique is under study due to its high flexibility and capability of minimizing surface equipment. In this study, a conceptual WE system, and operation procdure is introduced. The conceptual WE system consists of 3 main stations, which from the top are hoisting station (HS), canister connection station (CCS) and basement (BS). In HS, WE is controlled and monitored. The WE is controlled using wireline drum winch and sheaves, and load on wireline is measured using a load cell. HS also has a pressure control system (PCS), which monitors internal pressure of the system, and a lubricator, which act as housing for joint device, allowing the joint device to be easily inserted into the borehole. The joint device is used to connect the disposal canister to wireline for emplacement/retrieval. In CCS, a rail transporter brings a transport cask containing disposal canisters, then the transport cask is connected to the hoisting system and a PCS in the BS. The main component located at canister station are a sliding shielding door (SSD), and a slip. The SSD is used to prevent canister from falling into borehole during the connecting operation and prevent radiation from BS to affect the workers. The slip is located beneath the SSD and is used to hold the disposal canister before it is lowered into the borehole. In BS, PCS is installed to prevent overflow and blowout of borehole fluid. The PCS consists of wireline pressure valve, christmas tree and BOP, which all are a type of pressure valve to seal the borehole and release pressure inside the borehole. The WE procedure starts with transporting transport cask to CCS. The transport cask is connected to lubricator, and PCS. Joint device is lowered down to be connected with disposal canisters, then pulled up to check the load on the wireline. After the check-up, SSD is opened, and disposal canister is lowered into the borehole. When desired depth is reached, joint device is disconnected and retrieved for next emplacement. In this study, the conceptual deep borehole disposal system design implementing WE technique is introduced. Based on this study, further detailed design could be derived in future, and feasibility could be tested.

Equipment used for ships operating in the polar regions, such as icebreakers, should consider countermeasures against freezing. This study performed a structural design that prevents freezing and tolerates thermal stress and wind pressure of the air vent louver heating blades. As boundary conditions for performing the analysis, analysis was performed when the flow rates at the inlet end were 10m/s, 20m/s 30m/s, 40m/s, and 50m/s. As a result of the analysis, if the CNT heating element can maintain the heating performance of 200°C, the blade can maintain the room temperature state except for the end of about 40mm. There are pressure drop between the front and rear of the air vent louver. It can be seen that the allowable wind speed varies depending on the design criteria. As a results, it is required to select an optimal heating temperature to prevent condensation of a blade, optimize the generation of compressive stress by thermal expansion, and trade off the wind pressure and thermal stress according to wind speed.

PURPOSES : This study evaluates the long-term performance of the asphalt overlay designed by the Seoul pavement design method which determines overlay thickness by considering existing pavement conditions, traffic volume, and bearing capacity of the pavement. METHODS : A total of 76 sections including 17 control sections and 59 design sections were constructed under various traffic conditions, overlay thicknesses and asphalt mixtures. The performance of the pavements has been monitored up to 60 months in terms of surface distresses, rutting, and longitudinal roughness. The service life of the pavements was estimated to be the period when the Seoul pavement condition index (SPI) becomes 6.0, i.e., a rehabilitation level. RESULTS : Overall, the service life of the pavements was 72 months in the control and 120 months for the design sections. For relatively thinner overlay sections than designed, the service life reduced significantly; 36 months for 15cm thick overlay and 120 months for 25cm thick overlay. The service life of the pavement in the bus-only lane was 78 months, which is 30 months shorter than that in mixed-traffic lanes. Out of the bus-only lanes, 56% of the pavement along bus stop was deteriorated early to be a poor condition while only 2% of the pavement in a driving lane was degraded to be poor. The overlay with Stone Mastic Asphalt (SMA) in the wearing surface had 38% longer life than that with conventional dense graded mixtures. CONCLUSIONS : Most of the overlays sections designed by the Seoul pavement design method were expected to survive 10 years, except for bus-only lanes. The control sections having 5 to 10 cm thick overlays showed significant lower performance than the design sections. Thus proper thickness and materials considering the characteristics of existing pavement and traffic volumes should be applied to secure the service life of overlays.

In this paper, a method of reducing the weight of vehicle wheels through topology optimization by finite element method is proposed. Recently, various environmental pollution caused by the operation of vehicles is gradually increasing, and this has a great correlation with the fuel efficiency of the vehicle. Therefore, it is required to reduce the weight of the vehicle to increase fuel efficiency. Among them, the vehicle's wheels are a key part of vehicle acceleration and braking, and passenger safety. Because the shape of the wheels is different, various effects such as reduced fuel economy and reduced airpower occur as well as aesthetic factors. The stiffness of the wheels plays an important role in transmitting the vehicle's power to the tires and braking. In this study, to reduce weight while satisfying the stiffness value, we propose to use topology optimization to design an arbitrary shape according to the number of spokes on the wheel.

PURPOSES : The purpose of this study is to derive specific road design elements for safe urban underground and to adopt measures for minimizing traffic delays and to maintain efficient operation. METHODS : In this study, a qualitative study was conducted using Focus Group Interview (FGI) method to identify significant connection characteristics and develop connections to urban underground roads. Finally, this study analyzes design elements necessary for traffic safety and efficient traffic operation. In addition, relevant case studies were performed with keywords from the FGI method results. Therefore, major design elements were analyzed for urban underground road connection and connection analysis for traffic simulation-based verification. RESULTS : The main characteristics of the connection between the underground roads of the downtown area were divided into three types: traffic flow characteristics, geometric characteristics, and driver behavioral characteristics. From the review of 16 leading studies (10 domestic papers and 6 international papers) according to the characteristics, the main design factors for “traffic flow characteristics” include the traffic volume, design speed, heavy vehicle ratio, and lane change. The important design elements for “geometric characteristics” include the separation distance, number of lanes, slope, lane and shoulder width and the design factors for “driver behavioral characteristics” showed reaction time, driver vision, and driving speed. CONCLUSIONS : The FGI method identified the main characteristics of connections to the underground roads. In addition, the relevant empirical and theoretical research data were considered in case studies, and the design elements were derived and separated spatially based on the features of each design element, establishing a point-specific design element guideline.

The purpose of this study is to provide basic data to assist students and industrial designers in fashion by examining the trend of designing women’s wear with the SCAMPER method. In the research, the seven types of SCAMPER methods for fashion design were classified based on the previous studies. From 2010 S/S to 2020 S/S, data from 5,149 photographs were collected through overlapping checks and classified by SCAMPER method type. Data analysis was performed using SPSS 25.0 for frequency analysis. As a result, in the SCAMPER “combine” method, more than two items were combined, or structural details were combined with items. In the most applied “adapt” method was involved imitating similar images, or natural forms, or other objects. The “modify” method was applied by changing the shape of some details in basic fashion items. The “magnify” method was applied by enlarging, elongating, or elevating some details of fashion items. The “minify” method was applied by minimizing, shortening, or lowering some details of basic fashion. The method of “put to other use” was expressed throughout the clothing by using non-fabric or trimmings such as metal, beads, and strings. The “rearrange” method was applied by repositioning the top and bottom, front and back, or outside and inside in fashion items and in details. The “reverse” method was applied by reversing the style of fashion, mix-and-match fabric, or switching the gender of the fashion items.