Comparisons between bare carbon (CPs) and nitrogen-doped carbon nanoparticles (N-CPs) synthesised using hydrothermal reaction are carried out. It was found that hydrothermal reaction of citric acid yields graphene-like sheets, while the nitrogen doping using ethylenediamine resulted in amorphous polymeric ball-like hydrocarbons devoid of any aromatic rings. Although the Fourier transform infrared spectroscopy, Raman spectroscopy and nuclear magnetic resonance spectroscopy indicate the presence of carbon–carbon double bonds (C=C), and the ground states of both materials are very deep (> 7.8 eV) as measured by ultraviolet photoelectron spectroscopy. This indicates the conjugation is very short. This is supported by the fact that both materials are UV blue emitting peaking at 375 nm probably originating from C=C.

We present the analysis of KMT-2016-BLG-0212, a low flux-variation (Iflux−var ∼ 20 mag) microlensing event, which is in a high-cadence (Γ = 4hr −1) field of the three-telescope Korea Microlensing Telescope Network (KMTNet) survey. The event shows a short anomaly that is incompletely covered due to the brief visibility intervals that characterize the early microlensing season when the anomaly occurred. We show that the data are consistent with two classes of solutions, characterized respectively by low-mass brown-dwarf (q = 0.037) and sub-Neptune (q < 10−4) companions. Future high-resolution imaging should easily distinguish between these solutions.

In this study, an empirical relationship between the energy band gap of multi-walled carbon nanotubes (MWCNTs) and synthesis parameters in a chemical vapor deposition (CVD) reactor using factorial design of experiment was established. A bimetallic (Fe-Ni) catalyst supported on CaCO3 was synthesized via wet impregnation technique and used for MWCNT growth. The effects of synthesis parameters such as temperature, time, acetylene flow rate, and argon carrier gas flow rate on the MWCNTs energy gap, yield, and aspect ratio were investigated. The as-prepared supported bimetallic catalyst and the MWCNTs were characterized for their morphologies, microstructures, elemental composition, thermal profiles and surface areas by high-resolution scanning electron microscope, high resolution transmission electron microscope, energy dispersive X-ray spectroscopy, thermal gravimetry analysis and Brunauer-Emmett-Teller. A regression model was developed to establish the relationship between band gap energy, MWCNTs yield and aspect ratio. The results revealed that the optimum conditions to obtain high yield and quality MWCNTs of 159.9% were: temperature (700ºC), time (55 min), argon flow rate (230.37 mL min–1) and acetylene flow rate (150 mL min–1) respectively. The developed regression models demonstrated that the estimated values for the three response variables; energy gap, yield and aspect ratio, were 0.246 eV, 557.64 and 0.82. The regression models showed that the energy band gap, yield, and aspect ratio of the MWCNTs were largely influenced by the synthesis parameters and can be controlled in a CVD reactor.

To preserve the superior genetic resources and restore the endangered species, Somatic cell nuclear transfer (SCNT) has been used widely. In Korea, the research of dog cloning has made outstanding achievements including the production of the world`s first cloned dog. Sapsaree (Sapsalgae), the representative dog of Gyeongsan-si was designated as a Korea natural monument (No. 368). This male dog used in this study has azoospermia due to unknown cause. In this study, the aim was to confirm the cause of infertility in the cell donor dog and to evaluate the reproduction potential of dog cloning using infertile male dog by SCNT. First, to confirm the infertility of the cell donor dog, the reproductive history and the testis were evaluated. The breeding histology was not recorded in individual document. In histopathology, the Sertoli cell tumor was confirmed in biopsy of the cell donor dog after death. But, these tumors are predominantly in older dogs. Second, we produced the cloned dogs with the somatic cells of the infertile dog and the appearance was similar with the cell donor dog. Also, microsatellite analysis confirmed the genetic relationship between the cell donor and clone dogs. Third, the potential breeding capacity of the cloned dog was confirmed. In T4 assay, the normal dog (same age with cloned dogs), cell donor dog, and cloned dogs was investigated. The cell donor dog with azoospermia had very low T4 level, and cloned dogs showed higher level of T4 than normal dogs. In CASA, There was no significant difference in sperm motor ability between normal dogs and cloned dogs. As a result, cloned dogs produced by SCNT had no problem regarding the reproductive function of the testis. In AI experiment, the semen of clone dogs was used to fertilize a natural female bitch and was diagnosed pregnancy by ultrasonography. In total, 7 puppies were born by normal delivery (male: 3, female: 4). In conclusion, this study confirmed that the reproduction problem of non-genetic infertility can generate a normal descendant by SCNT. Also, the first successful research to restore infertile dogs was completed. Furthermore, SCNT would be useful for the restoration of endangered species and application of superior traits.

The world-wide need to reduce the energy used and the greenhouse gases emitted during cement manufacture has led to the pursuit of more eco-efficient materials, such as ground granulated blastfurnace slag(GGBS) and fly ash. Especially, GGBS is a by-product generated during the manufacture of pig ions. GGBS can be divided into water-cooled slag(WS) and air-cooled slag(AS). With comparison of WS, the AS is formed by allowing the molten slag to cool relatively slowly under ambient conditions. This study presents experimental findings on the mechanical and durability performance of cement concrete pavement with replacement of cement by WS and/or AS. In order to produce concrete specimens, total replacement of cement by GGBS(WS+AS) was fixed at 40% by mass. Concrete specimens were regularly monitored for the variation of mechanical properties such as flexural strength, compressive strength and initial surface absorption. In addition, in order to assess durability of concrete pavement with WS and/or AS, the chloride ion penetration resistance and scaling resistance tests were adopted, and the corresponding results were compared to those of plain concrete pavement. The test results indicated that the performance of concrete pavement was significantly dependent on the replacement level of WS by AS. Concrete specimens incorporating 20% replacement level of AS showed a poor mechanical performance, while 5% replacement of AS showed a beneficial effect both mechanical and durability performance. Especially, the 5% AS replacement led to the higher resistance of concrete pavement against frost-salt action. Based on the experimental results, the present study would be helpful to design high-performance cement concrete pavement.