코로나-19가 종식되지 않은 시점에서 위험을 감수하면서 운동을 지속하고 있는 필라테스 고객 들의 열정을 살펴봄으로써 고객이 느끼는 심리적 행복감과 운동지속의도를 규명하고자 한다. 대상은 필라 테스 고객 285명을 대상으로 하였다. 자료처리는 SPSS 21.0과 AMOS 18.0을 이용하였고, 빈도분석과 신 뢰도, 확인적 요인분석, 상관분석을 실시하였다. 또한 SEM 사용하여 경로분석을 실행하였으며, 부트스트래 핑을 활용하여 매개효과를 확인하였다. 첫째, 열정적 행동은 심리적 행복감에 정적인 영향을 미쳤다. 둘째, 열정적 행동은 운동지속에 정적인 영향을 미쳤다. 셋째, 심리적 행복감은 운동지속에 정적인 영향을 미쳤 다. 넷째, 열정적 행동과 운동지속의 관계에서 심리적 행복감이 부분적 매개 역할을 하였다.

본 연구는 미국에서의 기술경영 분야의 발전과정을 통해 기술경영의 정체성이란 무엇인가를 탐구한다. 미국에서 기술경영은 2차 대전 전후를 거치면서 현재까지 기술과 사회의 관계의 변화에 따라 내용을 달리해왔다. 본 연구에서는 (1) 2차 대전 전후의 ``R&D 관리`` 또는 ``프로젝트관리`` 단계, (2) 70-80년대 초반의 혁신에 대한 이론화 전개 단계, (3) 기술경영논의의 확대 및 기술경영교육의 확산 단계로 나누어 정리하였다. 이를 통해 기술경영의 개념 및 이해가 시대적 문제해결 과정에서 다양한 의미를 가지면서 진화해온 것을 확인할 수 있었다. 이러한 복수적 정체성은 그 자체가 병리적인 것이라기보다는 기술과 사회의 접점이 확대되고 있음을 보여주는 것이며, 기술경영교육의 측면에서는 다양한 접근이 필요하다는 함의를 제공해 준다.

The insecticidal potency of some essential oils have been suggested that they may find an application in the control of house dust mites. We compared the repellent effect of four essential oils ; lemon grass (Cymbopogon nardus), lavender(Lavandula vera), rosemary(Rosmarinus officinalis) and ylang ylang(Cananga odorata). The oils were exposed at different doses(0.1, 0.05, 0.025, 0.0125, and 0.00652 ㎕/㎠) and different times(1, 2, 3, 4, 5 hours) on house dust mites(Dermatophagoides farinae and D. pteronyssinus). The repellent effects(%) of essential oils that were exposed at 0.1 ㎕/㎠ and for 1 hours against house dust mites were lemon grass(63.3%) and rosemary(61%), lavender(40%), ylang ylang(40%) in the order named.

Recently, in our country has been heightened awareness of the performance of non-combustible construction materialsand eco-friendly. In addition, bottom ash can be used as a high-value, but it is a situation that is buried. Therefore, thebasic experimental study results on the development possibility of eco-friendly nonflammable floor finishing materialsusing the bottom ash, which is an industrial byproduct, are as follows: (1) As a test result of the compressive strengthof mortar conducted to review the use possibility of bottom ash as a floor finishing material, the standard mix that didnot use bottom ash showed 31.3MPa, a 25% replacement mix showed 33.7MPa and a 50% replacement mix showed33.6MPa. Consequently, higher results of the compressive strength of mortar were demonstrated up to the 50%replacement mix, compared to the standard mix. (2) As a flow test result by addition of superplasticizer, the flow was215mm in the 0.2% added mix, and 253mm in the 0.4% added mix. However, material separation was confirmed inthe case of the 0.4% added mix. Therefore, the addition meeting 190mm set forth in the KS F 4041 was 0.2%. (3) Asa result of bond strength test to review bond strength with concrete structure, it was 1.26MPa in case polymer powdercontent was 2%, except for 1.02MPa of basic mix, and it was 1.75MPa in the case of 4%, and all these met1.2MPaand more of bond strength set forth in the KS. (4) As a result of a wear resistance experiment conducted to review theuse possibility as a floor finishing material for parking lot, the mix meeting 0.15mg/mm2 or less of wear resistance setforth in the KS F 4041 was the case of 4% of polymer powder addition, which showed 0.13mg/mm2.

This study is to review its possibility of recycling, subject for Polyolefine (TPO) and Polyvinyl Chloride (PVC) among thermoplasticity plastic raw materials, of which recycling is possible. Wasted vinyl and processing by-products have been used for Polyolefine (TPO), and coating from used cable and its by-products used for Polyvinyl Chloride (PVC). The study result is shown as following. (1) In case of Polyolefine (TPO), superior property has been shown, when mixed with raw materials, as the property of by-products is excellent. For Polyvinyl Chloride (PVC), property in the same level as raw materials has been shown up to 50% of by-products mixing rates. (2) In case of coating from the used cable, the property as exactly same as raw materials without property loss has been shown since long time passed, with using highquality raw materials at that time of manufacture.