One of the important components of a nuclear fuel cycle facility is a hot cell. Hot cells are engineered robust structures and barriers, which are used to handle radioactive materials and to keep workers, public, and the environment safe from radioactive materials. To provide a confinement function for these hot cells, it is necessary to maintain the soundness of the physical structure, but also to maintain the negative pressure inside the hot cell using the operation of the heating, ventilation, and air conditioning (HVAC) systems. The negative pressure inside the hot cells allows air to enter from outside hot cells and limits the leakage of any contaminant or radioactive material within the hot cell to the outside. Thus, the HVAC system is one of the major components for maintaining this negative pressure in the hot cell. However, as the facility ages, all the components of the hot cell HVAC system are also subject to age-related deterioration, which can cause an unexpected failure of some parts. The abnormal operating condition from the failure results in the increase of facility downtime and the decrease in operating efficiency. Although some major parts are considered and constructed in redundancy and diversity aspects, an unexpected failure and abnormal operating condition could result in reduction of public acceptance and reliability to the facility. With the advent of the 4th Industrial Revolution, prognostics and health management (PHM) technology is advancing at a rapid pace. Korea Hydro & Nuclear Power, Siemens, and other companies have already developed technologies to constantly monitor the integrity of power plants and are applying the technology in the form of digital twins for efficiency and safety of their facility operation. The main point of PHM, based on this study, is to monitor changes and variations of soundness and safety of the operation and equipment to analyze current conditions and to ultimately predict the precursors of unexpected failures in advance. Through PHM, it would be possible to establish a maintenance plan before the failure occurs and to perform predictive maintenance rather than corrective maintenance after failures of any component. Therefore, it is of importance to select appropriate diagnostic techniques to monitor and to diagnose the condition of major components using the constant examination and investigation of the PHM technology. In this study, diagnostic techniques are investigated for monitoring of HVAC and discussed for application of PHM into nuclear fuel cycle facilities with hot cells.

Korea Atomic Energy Research Institute (“KAERI”) has been developing various studies related to the nuclear fuel cycle. Among them, KAERI was focusing on the pyroprocess, which recycles some useful elements white reducing the volume and toxicity of spent nuclear fuel (SNF). Pyroprocess involves the handling of SNF, which cannot be handled directly by the facility worker. Therefore, SNF is handled and processed through remote handling device within a shielded facility such as a hot cell. Nuclear Facilities with such hot cells are called nuclear fuel cycle facilities, and unlike other facilities, heating, ventilating, and air conditioning (HVAC) system are particularly important in nuclear fuel cycle facilities to maintain the atmosphere in the hot cell and remove radioactive materials. In addition, due to the nature of the pyroprocess, which uses molten salt, corrosion is a problem in air atmosphere, so the process can only be carried out in an inert gas atmosphere. KAERI has a nuclear fuel cycle facility called the Irradiation Material Examination Facility (IMEF), and has built and operated the ACPF inside the IMEF, which operates an inert atmosphere hot cell for the demonstration of the pyroprocess. For efficient process development of the pyroprocess, it is necessary to put the developed equipment into the hot cell, which is a radiationcontrolled area, after sufficient verification in a mock-up facility. For this purpose, the ACPF mock-up facility, which simulates the system, space, and remote handling equipment of the ACPF, is operated separately in the general laboratory area. The inert gas conditioning system of the ACPF consists of very complex piping, blowers, and valves, requires special attention to maintenance. In addition, if there is a small leak in the piping within these valves or piping, radioactive materials can be directly exposed to facility workers, so continuous monitoring and maintenance are required to prevent accident. In this study, the applicability of acoustic emission technology and ultrasonic technology for leak detection in the inert gas conditioning system of ACPF mock-up facility was investigated. For this purpose, new bypass pipes and valves were installed in the existing system to simulate the leakage of pipes and valves. Acoustic emission sensors are attached directly to pipes or valves to detect signals, while ultrasonic sensors are installed at a distance to detect signals. The optimal parameters of each technology to effectively suppress background noise were derived and, and the feasibility of identifying normal and abnormal scenarios in the system was analyzed.

Tungsten carbide is widely used in carbide tools. However, its production process generates a significant number of end-of-life products and by-products. Therefore, it is necessary to develop efficient recycling methods and investigate the remanufacturing of tungsten carbide using recycled materials. Herein, we have recovered 99.9% of the tungsten in cemented carbide hard scrap as tungsten oxide via an alkali leaching process. Subsequently, using the recovered tungsten oxide as a starting material, tungsten carbide has been produced by employing a self-propagating high-temperature synthesis (SHS) method. SHS is advantageous as it reduces the reaction time and is energy-efficient. Tungsten carbide with a carbon content of 6.18 wt % and a particle size of 116 nm has been successfully synthesized by optimizing the SHS process parameters, pulverization, and mixing. In this study, a series of processes for the highefficiency recycling and quality improvement of tungsten-based materials have been developed.

Owing to increasing demand of rare metals present in ICT products, it is necessary to promote the rare metal recycling industry from an environmental viewpoint and to prevent climate change. Despite the fact that information for toxic substances is partly indicated, a legal basis and an international standard indicating usage of rare metals is insufficient. In order to address this issue, a newly created study group of environment and climate change at the ITU (International Telecommunication Union) is doing research to develop methodologies for recycling rare metals from ICT products in an eco-friendly way. Under this group, the Republic of Korea has established two international standards related to rare metals present in ICT products. The first is ‘Release of rare metal information for ICT products (ITU-T L.1100)’ and the other is ‘Quantitative and qualitative analysis methods for rare metals (ITU-T L.1101)’. A new proposal for recommending the provision of rare metal information through a label by manufacturers and consumer/recycling businesses has been approved recently and is supposed to be published later in 2016. Moreover, these recommendations are also being extended to IEC, ISO and other standardization organizations and a strategy to reinforce the ability for domestic standardization is being established in accordance with industrial requirements. This will promote efficient recycling of rare metals from ICT products and will help improve the domestic supply of rare metals.