This study numerically investigates buckling behavior of press braked steel plates with a free edge. In order to improve structural stability during construction, the top flanges of press-braked U section girder are laterally braced by the installation of prefabricated half-deck. Thus, an unbraced length is taken as the longitudinal spacing of pockets on the half-deck, which are to make composite section. This study performed 3D finite element analyses to evaluate an equivalent effective width of cold-formed flange with a free edge. Through the parametric numerical analyses, the elastic buckling stresses of the cold-formed flanges with rounded corner in the cross-section were compared with those of general flat plates. Then, the equivalent effective width of the cold-formed (press-braked) flanges were numerically examined for some representative cases.

This paper is presented an experimental studies on bond stress between steel and concrete in concrete filled Rectangular steel tubes. In the actual building frames, vertical dead and live loads on beams are usually transferred to columns by beam-to-column connections. In case when concrete filled steel tubes are used as columns of an actual building frame which has a simple connection, shear forces in the beam ends are not directly transferred to the concrete core but directly to the steel tube. Provided that the bond effect between steel tube and concrete core should not be expected, none of the end shear in the beams would be transferred to the concrete core but only to the steel tube. Therefore, it is important to investigate the bond strength between steel tube and concrete core in the absence of shear connectors.

이 연구는 CRC기둥강도곡선의 비탄성영역에 대한 해석적 고찰이다. CRC기둥강도곡선의 비탄성영역은 최대 잔류응력 크기 0.5σy 와 Bleich이론을 기초로 하고 있다. 이는 실제로 알려진 최대 압축 잔류응력의 크기가 0.3σy 인 경우 보다 다소 보수적이다. 본 연구는 열압연강재의 최대 압축 잔류응력의 크기를 0.3σy 으로 고려하여 그에 따른 기둥강도곡선과 접선탄성계수 Et를 제안하고 이를 CRC에서 제안하고 있는 값들과 각각 비교 고찰한다. 축 압축력을 받는 비탄성 기둥의 응력은 기둥에 작용하는 하중이 좌굴을 일으키기 전에 재료의 비례한도를 넘어 항복점에 도달할 것이다. 따라서 점차적인 단면의 항복 상태에 따른 기둥강도곡선을 검토할 필요가 있다. 본 연구는 최대 압축 잔류응력 σr = 0.5σy 을 사용하여 재료의 항복에 따른 임계하중 곡선식을 유도하고 이를 CRC기둥강도곡선과 비교 고찰한다.

In this study, axial-stress distribution of enlarged concrete column according to degree of composite is analysed. The analysis showed that axial-stress on existing concrete and new concrete was concentrated to edge in case of lower degree of composite. On the other hand, axial-stress was evenly distributed in case of higher degree of composite.

The hollowed precast concrete (PC) column supports beams during construction so that local compression acts on the column. At that time, the stress distribution from the beams to the column varies if hollow size varies. After the hollow is filled with grout concrete, the column has two layer, outer and inner elements with different compressive strength each other. Therefore, hollow size affect axial capacity of column after filling the hollow. Based on the above background, this paper performed a finite element (FE) analysis with parameter of hollow size to find the stress distribution of hollowed PC column during construction as well as after construction. As an analysis result, the wider the hollow size is, the less local compress strength is during construction. Also, the axial compressive resistance of column decreased when the hollow size is wider.

탄-소성론에 근거한 콘크리트나 토질과 같은 재료의 파괴 포락선은 주응력을 축으로 하는 공간 좌표계상에서 인장의 등압(hydrostatic stress)축을 향해 기울어진 형태를 가지며 소성흐름이 상관소성흐름 법칙(associated flow rule)에 따라 결정될 경우 콘크리트의 거동 예측시에 과도한 체적 팽창률을 나타내게 된다. 본 논문에서는 콘크리트의 다축응력 하에서의 거동을 예측하기 위하여 비균일 경화(nonuniformh ardening)를 적용한 5계수 파괴 포락선과 등압축 방향 성분의 소성 흐름을 수정하는 비상관 소성흐름 법칙(non-associated flow rule)을 사용하여 비선형 유한요소해석 프로그램을 개발하였으며 신뢰성 있는 연구자의 다축응력 실험결과와 유한요소해석 프로그램의 해석결과를 비교하였다.