In general, the design response spectrum in seismic design codes is based on the mean-plus-one-standard deviation response spectrum to secure high safety. In this study, response spectrum analysis was performed using seismic wave records adopted in domestic horizontal design spectrum development studies, while three response spectra were calculated by combining the mean and standard deviation of the spectra. Seismic wave spectral matching generated seismic wave sets matching each response spectrum. Then, seismic fragility was performed by setting three damage levels using a single-degree-of-freedom system. A correlation analysis was performed using a comparative analysis of the change in the response spectrum and the seismic fragility concerning the three response spectra. Finally, in the case of the response spectrum considering the mean and standard deviation, like the design response spectrum, the earthquake load was relatively high, indicating that conservative design or high safety can be secured.

According to several seismic design standards, a ground motion time history should be selected similar to the design response spectrum, or a ground motion time history should be modified by matching procedure to the design response spectrum through the time-domain method. For the response spectrum matching procedure, appropriate seed ground motions need to be selected to maintain recorded earthquake accelerogram characteristics. However, there are no specific criteria for selecting the seed ground motions for applying this methodology. In this study, the characteristics of ground motion time histories between seed motions and spectral matched motions were compared. Intensity measures used in the design were compared, and their change by spectral matching procedure was quantified. In addition, the seed ground motion sets were determined according to the response spectrum shape, and these sets analyzed the response of nonlinear and equivalent linear single degrees of freedom systems to present the seed motion selection conditions for spectral matching. As a result, several considerations for applying the time domain spectral matching method were presented.

In this study, a design procedure for the practical application of the dampers to building structures under earthquake loads was presented by using earthquake response spectrum. Nonlinear time history results using a 10 story building structure installed with damper verified the effectiveness of the proposed procedure by showing that the structural response could be reduced to the target performance level for seismic loads. Since the proposed design procedures are based on response spectrum seismic analysis result of the original structure, the capacity, location and the number of damper and the consequent response reduction effects can be preliminarily determined without performing the nonlinear time history analysis.

The seismic damage of non-structural components, such as communication facilities, causes direct economic losses as well as indirect losses which result from social chaos occurring with downtime of communication and financial management network systems. The current Korean seismic code, KBC2009, prescribes the design criteria and requirements of non-structural components based on their elastic response. However, it is difficult for KBC to reflect the dynamic characteristics of structures where non-structural components exist. In this study, both linear and nonlinear time history analyses of structures with various analysis parameters were carried out and floor acceleration spectra obtained from analyses were compared with both ground acceleration spectra used for input records of the analyses and the design floor acceleration spectrum proposed by National Radio Research Agency. Also, this study investigates to find out the influence of structural dynamic characteristics on the floor acceleration spectra. The analysis results show that the acceleration amplification is observed due to the resonance phenomenon and such amplification increases with the increase of building heights and with the decrease of structure’s energy dissipation capacities.

건축물의 지진응답해석에서 입력지진동은 구조물의 비선형 응답에 중요한 영향을 미치는 요소이다. 지진동의 특성은 표층지반의 성질과 국부적인 지반 조건에 따른 여러 가지 인자에 의해 그 특성이 결정되기 때문에 구조물의 지진응답해석에서 일반성을 갖는 입력지진동을 선정하는 것은 매우 어려운 문제이다. 본 논문은 내진설계용 스펙트럼에 적합한 인공지진동파형을 작성한 후, 작성된 인공지진동에 의한 철근콘크리트 다층 골조구조물의 탄소성 응답특성을 분석한 것이다. 여기서 작성된 인공지진동파형은 과거 비교적 큰 규모의 지진에서 얻어진 기록지진동과 동일한 위상각을 가지며, 감쇠정수 h=5%일 때의 내진설계용 스펙트럼과 거의 일치하도록 작성하였다. 입력지진동의 탄성 가속도 응답스펙트럼이 동일한반면, 각 입력지진동띄 위상특성이 다른 인공지진동을 입력하여 다자유도 골조 구조물의 지진응답을 분석하여 건축물의 내진설계용 지진동으로서 타당성을 확인하는 것이 목적이다. 본 논문에서 작성된 인공지진동은 기록지진동에 비해 지진응답치가 안정된 값을 나타내는 것을 확인할 수 있었다. 그러므로 다층 골조구조물의 비선형 지진응답해석용 입력지진동으로 타당성이 높다고 사료되며, 비선형 지진응답해석용 입력지진동의 강도를 탄성 가속도 응답스펙트럼으로 규준화 하는 것이 합리적이라고 사료된다.

건축구조물의 비선형 지진응답해석에서 입력지진동은 구조물의 탄소성 지진응답을 좌우하는 중요한 요소이다. 지진동파형은 지진발생과 전파경로에 따른 여러 가지 인자에 의해 그 특성이 결정되기 때문에 구조물의 지진응답해석에서 일반성을 갖는 입력지진동을 선정하는 것은 매우 어려운 문제이다. 본 논문은 내진설계용 스펙트럼에 대응하는 인공지진동파형을 작성한 후, 작성된 인공지진동에 대한 탄소성 응답스펙트럼 특성을 분석한 것이다. 여기서 작성된 인공지진동파형은 과거의 지진에서 얻어진 기록지진동파형을 이용하여 기록지진동과 동일한 위상각을 가지며, 감쇠정수 h=5%일 때의 내진설계용 스펙트럼과 거의 일치하도록 작성되었다. 작성된 인공지진동은 원 기록지진동과 동일한 위상각을 가지며, 주기 T=0.02{\sim}10.0sec 범위에서 설계용 스펙트럼과 매우 근접하게 작성되었다. 인공지진동을 입력한 1자유도계의 탄성 및 탄소성 지진응답해석을 수행하여 탄소성 응답스펙트럼 및 탄소성 응답특성을 분석하였다. 본 논문에서 작성된 인공지진동은 건축구조물의 탄소성 지진응답해석용 입력지진동으로 충분히 타당성이 있다고 사료된다.

This study presented the seismic performance of weir structures with infinite foundations subjected to seismic ground motions, rather than finite soil foundation to avoid the reflection of seismic wave propagation at the mesh boundaries. The analytical model of weir structures was developed in ABAQUS　platform and then the seismic performance of concrete weir structure was evaluated through design response spectrum (KBC 2009). It was revealed that the maximum stresses obtained from infinite models was significantly increased, in comparison to the finite models.

Since Mt. Baeck-du is considered to be 8 or more in VEI scale, it is obviously crucial work to understand the dynamic characteristics of volcanic earthquakes for prediction of the possible damage in South Korea due to the future eruption of Mt. Baeck-du. This study aims to investigate the dynamic characteristics and propose design response spectrum for volcanic earthquakes.