The dismantlement of the Kori Unit 1 and Wolsong Unit 1 nuclear power plants is scheduled. Since about 40% of the cost of dismantling nuclear power plants is the cost of disposing of generated wastes, it is important to secure recycling technologies. Among them, low and intermediate level radioactive wastes are made of porous filters and adsorbent materials of ceramic foam to remove nuclides such as C-14, I, and Xe generated during nuclear dismantling. In order to remove a large amount of nuclides, physical properties such as a specific surface area and porosity of a ceramic foam filter are important, however when a heat treatment temperature is increased to increase the strength of the filter, the nuclides removal ability is reduced. In order to remove a large amount of nuclides, physical properties such as a specific surface area and porosity of a ceramic foam filter are important, however when a heat treatment temperature is increased to increase the strength of the filter, the nuclides removal ability is reduced. Therefore, in this study, the foam filter performance was improved by applying a sacrificial material to increase the specific surface area and porosity of the ceramic foam filter. The sacrificial material is burned out with polyurethane (PU) of the green filter before the heat treatment temperature to increase the strength of the ceramic foam filter so that it can be maintained as pores, thereby improving the specific surface area and porosity. The sacrificial materials and melting temperature (Tm) reviewed in this study were anthracite (530~660°C), PMMA (160°C), Cellulose acetate (260~270°C), and aluminum particle (660°C), and their effect on the manufacture of foam filters was studied by applying this. The specific surface part and porosity of the foam filter were improved when anthracite and aluminum particle were added, and PMMA and Cellulose acetate, which are relatively low temperature melting points, were burned out at a temperature lower than PU, and thus their physical properties were not greatly affected. The physical properties and specific surface part and porosity of ceramic foam filters manufactured using various sacrificial materials will be discussed.

In this study, the experiments and analyses were carried out in order to investigate the fracture characteristics on the adhesive at the specimen bonded with aluminum and aluminum-foam. The same conditions were given for the experiments and analyses. The results are investigated by the graph of reaction force according to displacement. It was found that the experimental and the analytical data were very similar to each other. On the basis of the data, the reliability of the analysis data could be confirmed. The notches were produced at the distances of 40, 110, 150, and 190 mm from the front of the test specimen, and the maximum reaction force was compared accordingly. It was found that the highest reaction force was generated at the front end of the adhesive and the lowest reaction force was found at the middle of the adhesive interface. Finally, when the equivalent stress in the test specimen was examined, it was found that the highest stress was obtained at the distance of 110 mm. It can be deduced. As the notch formation point are similar to the point when stress is dispersed as the adhesive is peeled off, it is possible to infer the high stress compared to other test specimens.

In this study, we investigated the properties of adhesive materials with different lightweight materials such as CFRP and Al-foam. The specimens were tested and analyzed using DCB (Double Cantilever Beam) specimens. In order to secure the reliability of the finite element method, the test and analysis were carried out, and the reliability of the finite element method was secured by using the graph of reaction force to displacement based on the experiment and analysis. The study on the adhesive failure characteristics according to the position of notch hole proceeded. Notch holes were generated at the locations of 40, 110, 150 and 190 mm from the beginning of the specimen near the bonding interface, and the analysis conditions used were the same as those used for securing reliability. The obtained study results are compared with reaction force and equivalent stress. In the case of reaction force, the overall tendency is similar but the difference in maximum reaction force is found. It was found that higher reaction forces appeared at the beginning than at the end of the bonding interface. When the equivalent stresses in the specimens were examined, the value of CFRP was seen to be 30 times higher as much as that of Al-foam.

Porous materials such as polymeric foam are widely adopted in engineering and biomedical fields. Porous materials often exhibit complex nonlinear behaviors and are sensitive to material and environmental factors including cell size and shape, amount of porosity, and temperature, which are influenced by the type of base materials, reinforcements, method of fabrication, etc. Hence, the material characteristics of porous materials such as compressive stress-strain behavior and void volume fraction according to aforementioned factors should be precisely identified. In this study, unconfined uniaxial compressive test for two types of closed-cell structure polyurethane foam, namely, 0.16 and 0.32 g/cm3 of densities were carried out. In addition, the void volume fraction of three different domains, namely, center, surface and buckling regions under various compressive strains (10%, 30 %, 50 % and 70 %) were quantitatively observed using Micro 3D Computed Tomography(micro-CT) scanning system. Based on the experimental results, the relationship between compressive strain and void volume fraction with respect to cell size, density and boundary condition were investigated.