In emergency situations such as nuclear accidents or terrorism, radioactive and nuclear materials can be released by some environmental reasons such as the atmosphere and underground water. To secure the safety of human beings and to respond appropriately emergency situation, it is required to designate high and low dose rate regions in the early stages by analyzing the location and radioactivity of sources through environmental radiation measurement. This research team has developed a small gamma probe which is featured by its geometrical accessibility and higher radiation sensitivity than other drone detectors. A plastic scintillator and Silicon Photomultiplier (SiPM) were applied to the probe to optimize the wireless measurement condition. SiPM has a higher gain (higher than 106) and lower operating voltage (less than 30 V) compared to a general photodiode. However, the electronic components in the SiPM are sensitively affected by temperature, which causes the performance degradation of the SiPM. As the SiPM temperature increases, the breakdown voltage (VBD) of the SiPM also increases, so the gain must be maintained by applying the appropriate VBD. Therefore, when the SiPM temperature increases while the VBD is fixed, the gain decreases. Thus, the signal does not exceed the threshold voltage (VTH) and the overall count is reduced. In general, the optimal gain is maintained by cooling the SiPM or through a temperature compensation circuit. However, in the developed system, the hardware correction method such as cooling or temperature compensation circuit cannot be applied. In this study, it was confirmed that the count decreased by up to 20% according to the increase in the temperature of the SiPM when the probe was operated at room temperature (26°C). We propose methods to calibrate the total count without cooling device or compensation circuit. After operating the probe at room temperature, the first measured count is set as the reference value, and the correction factor is derived using the tendency of the count to decrease as the temperature increases. In addition, since this probe is used for environmental radiation monitoring, periodic measurements are more suitable than continuous measurements. Therefore, the temperature of the probe can be maintained by adding a power saving interval to the operation sequence of the probe. These two methods use the operation sequence and measurement data, respectively. Thus, it is expected to be the most effective method for the current system where the temperature compensation through hardware is not possible.

The purposes of this research are to modelize test system of SM TESTING by ARENA, software, input several items of specimen’s testing process, resources of system and transfer loop, etc, give a hypothesis and then, obtain results reducing the efficiency of the whole system finally by overload of specific facilities in the testing system through the simulation so as to obtain several materials such as specimen and testing facility, transfer loop, etc. by simple and various forms without any necessity of numerical modelization. It will add facilities of over load and reduce facilities with low operation rate, so increase the efficiency of the system.

When weapon system is designed and developed, a reliability is one of important factors to determine the development goal. The reliability analysis of the weapon system and equipment is based on MIL Specification, MIL-HDBK-217F and MIL-HDBK-338B. And the weapon system is operated on various environments by operating concept of the military using the weapon system. This study, at first, present failure rate by PSA comparing with failure rates by PCM, the different reliability analysis method, for same CCA(Circuit Card Assembly). And the study present change of reliability analysis results for CCA on various operation environment condition..

농작업을 수탁 대행하는 경제주체에 있어서 사업운영상 가장 중요한 문제가 되는 것은 농작업수탁요 금 즉, 농기계임작업요금의 설정이 문제이다. 그리고 농기계 수탁작업의 주체는 농협, 지방자치단체, 농 업경영인 등으로 다양하며, 따라서 임작업료의 요금설정체계도 다양하다. 본 연구에서는 원가회계의 측 면에서 농업기계임작업의 요금설정방식으로서 원가계산모형을 활용하는 경우의 유용성과 문제점을 분명 히 하고, 원가계산 시스템과 원가정보를 이용한 요금설정방식의 이론적 타당성을 제시하고자 한다.