PURPOSES : The purpose of this study is to establish a scientific and rational structure pavement maintenance technique and management standard through field investigation and analysis method development for measuring damage to structure pavement such that fundamental quality improvement can be promoted and the life of pavement prolonged. METHODS : In this study, the crack, plastic deformation, IRI, and SPI values measured using the existing RoadScanner of a corresponding section, as well as the relative dielectric constant values of a lower deck measured using a ground penetrating radar are reduced. The results of a small impact load test are verified by comparing the modulus of elasticity measured. RESULTS : In the Hongjecheon Overpass, when comparing the suspicion points of deterioration between the center of the lane and the 25 measurement data points of the wheel pass section based on the elastic modulus of the light falling weight deflectometer (LFWD), it is discovered that the lane comprises four centers (16%) and 18 wheelpaths (72%). The percentage of suspected deterioration points in the center is higher than that in the wheelpath. In addition, in the case of the Seoho Bridge, by comparing the suspicious points of deterioration for 11 measurement data points in the middle of the lane and the wheelpath section based on the elastic modulus of the LFWD, it is discovered that five points (45%) in both the middle of the lane and the wheel pass are similar. CONCLUSIONS : In this study, a comparative analysis of the LFWD elastic modulus and SPI factors (crack rate, plastic deformation, and IRI) of the Hongjecheon Overpass and Seoho Bridge is conducted to confirm the factors of pavement breakage. Among them, it is confirmed that it affects the pavement condition the most; however, to consider the LFWD elastic modulus as an evaluation criterion for future structure pavement, the data points must be verified via additional experiments to ensure high reliability.

PURPOSES : The purpose of this study is to analyze the impact of the level of the light-environment and the driver's visual ability on the change in the driver's perception of a forward curved section at night. The study also aims to identify factors that should be considered to ensure safety while entering curved sections of a road at night. METHODS : Data collected from a virtual driving experiment, conducted by the Korean Institute of Construction Technology (2017), were used. Logistic regression was applied to analyze the effects of changes in the light-environment factors (road surface luminance and glare) and the driver’s visual ability on a driver's perception of the road. Additionally, analysis of the moderated effect of visual ability on light-environment factors indicated that the difference in drivers’ visual abilities impact the influence of light-environment factors on their perception. A driver's ability to perceive, as a response variable, was categorized into 'failure' and 'success' by comparing the perceived distance and minimum reaction sight distance. Covariates were also defined. Road surface luminance levels were categorized into 'unlit road surface luminance' (luminance ≤ 0.1 nt) and 'lit road surface luminance' (luminance > 0.1 nt), based on 0.1 nt, which is the typical level observed on unlit roads. The glare level was categorized as 'with glare' and 'without glare' based on whether the glare was from a high-beam caused by an oncoming vehicle or not. The driver's visual ability level was categorized into 'low visual ability' (age ≥ 50) and 'high visual ability' (age ≤ 49), considering that after the age of 50, the drive’s visual ability sharply declines. RESULTS : The level of road surface luminance, glare, and driver's visual ability were analyzed to be significant factors that impact the driver's ability to perceive curved road sections at night. A driver's perception was found to reduce when the road surface luminance is very low, owing to the lack of road lighting ('unlit road luminance'), when glare is caused by oncoming vehicles ('with glare'), and if the driver's visual ability level is low owing to an older age ('low visual ability'). The driver's ability to perceive a curved section is most affected by the road surface luminance level. The effect is reduced in the order of glare occurrence and the driver's visual ability level. The visual ability was analyzed as a factor that impacts the intensity of the effect of change of the light-environment on the change of the driver's ability to perceive the road. The ability to perceive a curved section deteriorates significantly in 'low visual ability' drivers, aged 50 and above, compared to drivers with 'high visual ability,' under the age of 49, when the light-environment conditions are adverse with regard to the driver’s perception (road surface luminance: 'lit road surface luminance'→'unlit road surface luminance,' glare: 'without glare'→'with glare'). CONCLUSIONS : Supplementation, in terms of road lighting standards that can lead to improvements in the level of light-environment, should be considered first, rather than the implementation of restrictions on the right of movement, such as restricting the passage of low visual ability or aging drivers who are disadvantageous in terms of gaining good perception of the road at night. When establishing alternatives so that safety on roads at night is improved, it is necessary to consider improving drivers' perception by expanding road lighting installation. The road lighting criteria should be modified such that the glare caused by oncoming traffic, which is an influential factor in the linear change in perception, and the level of light-environment thereof are improved.

This study is for the safety display device to the transportation of the road that are installed on the boundary stone. This device includes an upper side that is located and fixed on the boundary stone top, and a side that is fixed on the boundary stone front. Solar cell convert light of solar to electric energy is equipped inside the upper side. the device’s side part is consisted 3 part. the charging unit for charging the electric energy generated from the solar cell to charge the battery, the illuminance sensing unit for detecting the night, and the LED unit for flashing traffic sign in night. furthermore this device can be installed easily on the boundary stone. and it can help driver to aware road and boundary stone by improving visibility in night time.

PURPOSES: The purpose of this paper is to demonstrate to the practicing engineers, how to apply the advanced composite materials theory to the road structures. For general construction material used, there is certain theoretical limit in sizes. For super road structure construction, the reduction in panel weight is the first step to take in order to break such size limits. METHODS: For a typical road structures panel, both concrete and advanced composite sandwich panels are considered. The concrete panel is treated as a special orthotropic plate. RESULTS: All types of advanced composite sandwich panels are considered as a self-weights less than one tenth of that of concrete panel. The concrete panel is treated as a special orthotropic plate to obtain more accurate result. CONCLUSIONS: Advanced composite sandwich panels are considered as a self-weights less than one tenth (10%) of that of concrete panel, with deflections less than that of the concrete panel. This conclusion gives good guide line for design of the light weight of road structures.

The expansion of old road is needed in constructing the entrance at the ○○I/C road in ○○city. To strength the national competition, many agents who concerned do their best for finishing that construction early as soon as possible. In generally, soil embankment on soft foundation is caused to reduce the stability by making the settlement of ground surface due to the over load. Thus, we try to make it stable by building EPS embankment construction which in our working place is one kind of the method of light embankment construction after excavating the original ground.