This study investigates the behavior of the thermal conductivity among material properties in order to develop a thermal evaluation methodology of spent fuel assembles in a transport cask. It is inefficient to model each element of the spent fuel assembly in detail, and it is generally calculated by modeling the effective thermal conductivity (ETC). The ETC model was developed to allow a much simpler representation of a spent fuel assembly within a fuel compartment by treating the entire spent fuel rod array and the surrounding fill gas within the confines of the compartment as a homogenous solid material. The fuel rod assembly and surrounding gas are modeled with an effective conductivity that is designed to yield an overall conduction heat transfer rate that is equivalent to the combined effect of local conduction and radiation heat transfer in a plane through the assembly. When this model is applied to the transport cask, it tends to predict the cladding peak temperature lower than the results of detailed model in which the fuel rod arrangement and shape of the fuel assembly are simulated. As for the tendency of the error, the model tended to under-predict when basket temperature was lower than a certain temperature, and over-predict when it was higher. The purpose of this study is to investigate the attenuation effect of the cladding peak temperature on the related variables when the ETC model is applied to the transport cask. In addition, based on the thermal characteristics of this model, a correction factor that can compensate for this attenuation effect is presented. This correction factor is obtained by finding the difference between a separate ETC homogeneous model and a separate detailed fuel model, rather than directly applying the ETC calculated from the detailed fuel model to the transport cask.

In the event of a loss of a SNF (spent nuclear fuel) transport cask during maritime transportation, it is essential to evaluate the critical depth at which the integrity of the cask can be maintained under high water pressure. SNF transport casks are classified as Type B containers and the integrity of of the containment boundary must be maintained up to a depth of 200 meters unless the containment boundary was breached under beyond-design basis accidents. However, if an intact SNF cask is lost at a depth deeper than 200-meter, release of radioactive material may occur due to breach of containment boundary with over-pressure. In this study, we developed a code for the evaluation of the pressure limit of SNF transport cask, which can be evaluated by inputting the main dimensions and loading conditions of cask. The evaluation model was coded as a computer module for ease of use. In the previous study, models with three different fidelities were developed to ensure the reliability of the calculation and maintain sufficient flexibility to deal with various input conditions. Those three models consisted of a high-fidelity model that provided the most realistic response, a low-fidelity model with parameterized simplified geometry, and a mathematical model based on the shell theory. The maximum stress evaluation of the three models confirmed that the mathematical model provides the most conservative results than the other two models. The previous results demonstrate that mathematical models can be used in the code of computer modules. In this study, additional models of transport cask were created using parametric modeling techniques to improve the accuracy of the pressure limit assessment code for different cask and situations. The same boundary conditions and loading conditions were imposed as in the previous simplified model, and the maximum stress results considering the change in the shape of the transport container were derived and compared with the mathematical model. The comparison results showed that the mathematical model had more conservative values than the simplified model even under various input conditions. Accordingly, we applied the mathematical model to develop a transportation container pressure limit evaluation code that can be simulated in various situations such as shape change and various situations.

In case a spent nuclear fuel transport cask is lost in the sea due to an accident during maritime transport, it is necessary to evaluate the critical depth by which the pressure resistance of the cask is maintained. A licensed type B package should maintain the integrity of containment boundary under water up to 200 m of depth. However, if the cask is damaged during accidents of severity excessing those of design basis accidents, or it is submerged in a sea deeper than 200 m, detailed analyses should be performed to evaluated the condition of the cask and possible scenarios for the release of radioactive contents contained in the cask. In this work, models to evaluate pressure resistance of an undamaged cask in the deep sea are developed and coded into a computer module. To ensure the reliability of the models and to maintain enough flexibility to account for a variety of input conditions, models in three different fidelities are utilized. A very sophisticated finite element analysis model is constructed to provide accurate response of containment boundary against external pressure. A simplified finite element model which can be easily generated with parameters derived from the dimensions and material properties of the cask. Lastly, mathematical formulas based on the shell theory are utilized to evaluate the stress and strain of cask body, lid and the bolts. The models in mathematical formula will be coded into computer model once they show good agreement with the other two model with much higher fidelity. The evaluation of the cask was largely divided into the lid, body, and bottom, bolts of the cask. It was confirmed that the internal stress of the cask was increased in accordance with the hydrostatic pressure. In particular, the lid and bottom have a circular plate shape and showed a similar deformation pattern with deflection at the center. The maximum stress occurred where the lid was in the center and the bottom was in contact with the body. Because the body was simplified and evaluated as a cylinder, only simple compression without torsion and bending was observed. The maximum stress occurred in the tangential direction from the inner side of the cylinder. The bolt connecting the lid and the body was subjected to both bending and tension at the same time, and the maximum stress was evaluated considering both tension and bending loads. In general, the results calculated by the formulas were evaluated to have higher maximum stresses than the analysis results of the simplified model. The results of the maximum stress evaluation in this study confirms that the mathematical models provide conservative results than the finite element models and can be used in the computer module.

Thermal analysis and safety assessment of spent fuel transport cask are mainly conducted using commercial Computational Fluid Dynamics (CFD) codes based on Finite Volume Method (FVM). The reliability and predictability of CFD codes have greatly been improved by the development in the computer systems, and are widely used to calculate heat flow in complex structures that cannot be analyzed theoretically. In the field of thermal analysis using the CFD code, it is important to clearly reflect the physical model of the transport cask, and a grid configuration suitable for the physical model is essential for accurate analysis. However, since there are no clear standard and guidelines for grid configuration and size, it is highly dependent on the user’s insight. Spatial discretization errors result from the use of finite-width grids and the approximation of the differential terms in the model equations by difference operators. Since the user usually cannot change the truncation error order of a given discretization scheme, spatial discretization errors can only be influenced by the provision of optimal grids. Therefore, it is necessary to quantify the spatial discretization errors caused by the grid. In the case of Orano TN’s NUHOMS® MP197 transport cask, considering four grids for two sets, the temperature uncertainty of the neutron shield, which has the lowest margin at the limit temperature among transport cask components, was quantified by applying 5-step procedure of the Grid Convergence Index (GCI) method for the uncertainty estimation presented in ASME V&V 20-2009. In the case of domestic spent nuclear fuel transport cask (KORAD21), neutron shield among the transport cask components has the lowest margin at the limited temperature. Accordingly, in this study, the temperature uncertainty of the neutron shield was quantified by applying GCI to three sets considering seven grids. As a result of the calculation, the uncertainty was less than ± 1°C, and the temperature of the neutron shield including the uncertainty was evaluated to be maintained below the limit temperature of 148°C.

As the saturation rate of temporary storage facilities for spent nuclear fuel increases, regulatory demands such as interim storage and permanent disposal of spent nuclear fuel are expected to begin in earnest. Considering the domestic situation where all nuclear power plants are located on the waterfront site, the interim storage site is also likely to be located on the waterfront site, and maritime transportation is one of the essential management stages. Currently, there are no independently developed maritime transportation risk assessment code in Korea, and no research has been conducted to evaluate the release of radioactive waste due to the sinking of transport container. Therefore, it is necessary to secure technology to properly reflect the domestic maritime transportation environment and to assess the impact of the sinking accident and to carry out safety regulations. To accurately calculate the releaser rate of radionuclides contained in a cask with breached containment boundary, the flow rate through the gap generated in the containment boundary should be calculated. The fluid flow through this gap which is probably in micro scale in most situations should be evaluated combining the fluid flow inside and outside the cask. In this study, a detailed computational fluid dynamics model to evaluate the internal fluid flow in the cask and a simplified model to capture the fluid flow and the heat transfer around the cask in the sea are constructed. The results for the large scale model are compared with the analytic formula for verification of heat transfer coefficient and they showed good agreements. The heat transfer coefficient thus found can be used in the detailed model to provide more realistic data than those obtained from assumed heat transfer coefficient around the surface of the cask. In the future, fluid flow through the gap between the lid and the body of the cask will be evaluated coupling the models developed in this work.

To rationalize the protection of spent nuclear fuel transport storage cask, we intend to investigate the status of domestic and foreign safety regulations and related technologies to develop sabotage scenarios and analyze the protection performance and radiation impact of transport storage cask. It is essential to conduct an aircraft collision safety evaluation on spent nuclear fuel transportation and storage casks in Korea due to changes in laws and regulations related to nuclear power plant design and demand for enhanced safety. Domestic and foreign research on the protection performance of spent nuclear fuel transport storage cask was based on 9.11 events, and the results of all studies show that the speed of the aircraft and leakage of nuclear materials are insignificant. The Sandia National Laboratory (SNL) calculates Aerosol emissions from spent fuel damage in the event of sabotage and calculates Source Term based on the Durbin-Luna model. In this paper, radiation sensitivity analysis was performed due to damage to the carrier according to the size of the accident, assuming that there was a hole enough to basket from the external shell among the collision scenarios identified for domestic cask models.

고리 원전 사용후핵연료 저장조의 저장용량을 확보하기 위하여 2002년부터 사용후핵연료 운반용기를 이용하여 400다발 이상의 PWR 사용후핵연료 집합체를 원전부지 내에 수송, 저장하였다. 이를 위하여 KN-12 운반용기, 관련장비 및 수송차량으로 구성되는 수송시스템을 구성하였다. KN-12 운반용기는 국내 원자력법 및 IAEA의 수송규정에 따라 설계, 제작되고, 정부로부터 인허가를 획득하였으며, 취급장비 역시 관련규정에 따라 구비하였다. 수송 저장작업은 2 대의 운반용기를 동시에 투입하여 수행하였으며, 모든 작업공정에 대하여 엄격한 품질관리 및 방사선 안전관리를 수행하여 수송 안전성을 확보하고 신뢰도를 제고하였다.