Using alkali treatment solution, neutrality treatment solution and acid treatment solution, the surface corrosion layer of copper plates and bronze plates that have been artificially corroded using HCl, H2SO4 and HNO3 solutions were removed. In the case of alkali treatment solution, only air oxidation in the form of black tenorite and white cuproous chloride remained without being removed. In the case of using a neutrality treatment solution, a anhydrous type layer of reddish brown cupric chloride remained without being removed, together with this black and white corrosion substance. In the case of using an acid treatment solution, this red corrosion substance also remained, but all of the oxide was removed on the surface of the specimen that was treated by alternatively using alkali treatment solution and acid treatment solution. In the case of this treatment solution with the order of alkali-acid, oxidation no longer proceeded only through the distilled water cleaning process after treatment, thereby showing that oxidation from the cleaning solution no longer proceeded.

순환전압전류법을 사용하여 전류-전압 곡선을 측정하였다. 전기화학적 특성과 금속의 표면상태간의 관계는 전자현미경(SEM)을 사용하여 조사하였다. 그리고 순환전압전류법에 의한 전기화학적 측정은 3 전극 시스템을 사용하였다. 측정 범위는 초기 포텐셜에서 -1350 mV까지 환원시키고, 연속적으로 1650 mV까지 산화시키고, 다시 초기지점으로 환원시켜 측정하였다. 스캔속도는 50, 100, 150, 200 및 250 mV/s를 선정하였다. 그 결과, 부식억제로 모노에탄올아민(MEA)을 사용하여 금속의 C-V 특성은 순환전압전류법으로부터 산화 전류에 기인한 비가역 공정으로 나타났다. 부식억제제로 MEA을 사용하였을 경우에는 전해질의 농도가 증가할수록 확산계수가 감소하는 경향을 나타내었다. 그리고 구리의 SEM 이미지를 보면, 전해질 농도를 증가시키면 표면부식은 증가하였다. 부식억제제로 1.0×10-3M MEA를 첨가시키면, 전해질 농도 0.1 N의 경우 확산계수가 상대적으로 커서 부식억제 효과가 적었다.

In this study, we investigated the C-V diagrams and metal surface related to the electrochemistry characterization of metal(nickel, SUS-304). We determined electrochemical measurement by using cyclic voltammetry with a three-electrode system. A measuring range was reduced from initial potential to -1350mV, continuously oxidized to 1650 mV and measured to the initial point. The scan rate were 50, 100, 150, 200 and 250 mV/s. As a result, the C-V characterization of metal using N,N-dimethylacetamide and N,N-dimethylformamide inhibitors appeared irreversible process caused by the oxidation current from the cyclic voltammogram. After adding organic corrosion inhibitors, adsorption film constituted, and the passive phenomena happened. According to the results by cyclic voltammetry method, it was revealed that the addition of inhibitors containing amide functional group enhances the corrosion resistance properties.

A study on the corrosion inhibition of metals is important in many industrial applications (carbon steel, copper, aluminum, SUS 304, nickel). In this study, we investigated the C-V diagrams related to the surface corrosion of metals. It was observed through the SEM that the surface corrosion state of the various metals had the corrosion potential by the scan rate and the organic inhibitor containing an amine group. We determined to measure cyclic voltammetry using the three-electrode system. The measurement of oxidation and reduction ranged from -1350mV to 1650mV. The scan rate was 50, 100, 150, and 200mV/s. It turned out that the C-V characterization of SUS 304 was irreversible process caused by the oxidation current from the cyclic voltammogram. After adding organic inhibitors, the adsorption film was constituted, and the passive phenomena happened. As a result, it was revealed that the inhibition effect of metal corrosion depends on the molecular interaction, and the interaction has influence on the adsorption complex.

The purpose of this experiment was to find out the effects on metal corrosion of 2 types of tree, 7 types of wood based products and 4 types of cement that is currently being used as internal museum materials. By using the Oddy test as a corrosion test, with the materials that are used in the museum and the metal test pieces(Gilding, Silver, Iron, Bronze, Copper) are exposed in a high temperature( 60℃ ) and humidity for 28 days. After 28 days, we compare and analysis the difference between the metal test piece that was used before and after the test. We found that gilding and bronze did not occur corrosions on the surface but iron(Fe)and copper(Cu) also silver(Ag) had corrosions on the surface in different forms.

산업화, 도시화로 인해 수자원의 오염이 악화 되면서 기존에 염소를 이용한 정수처리 방법으로는 깨끗한 물을 공급하는데 어려운 실정이다. 이에 오존을 이용한 고도정수 처리 시설의 도입이 증가하고 있다. 그러나 기존의 방수⋅방식 공법으로 사용되는 에폭시계 방수⋅방식제 및 스테인리스는 오존의 강력한 산화력으로 인해 열화되어 박리 등 문제 발생하였으며, 콘크리트까지 영향을 미쳐 내구성 저하의 원인이 된다. 이에 따라 본 연구에서는 내오존성 및 내화학성이 뛰어난 금속 패널을 기존의 시공법 보다 손쉬운 방법으로 시공하기 위한 방법으로 금속용사 공법을 이용하여 수처리 시설 콘크리트 구조물의 열화를 원천적으로 방지하기 위한 마감공법 개발 연구의 일원으로 용사금속 종류 에 따른 내오존성 평가를 실시하였으며, 실제 하수처리장 환경에서의 전기화학적 안정성능 평가를 실시하였다. 실험결과 용사금속 Ti이 용사 후에도 내오존성이 뛰어난 것으로 나타났으며, 하수처리장 환경에서의 전기화학적 안정성능 평가 결과 용사금속 Ti가 403.83k∙ Ω∙cm2의 가장 높은 분극저항을 나타남으로써 높은 수준의 내구성을 확보하는 것을 확인할 수 있었다.

The main cause of corrosion in reinforced concrete is diffusion of degradation factors such as chloride ions, carbon dioxide, and sulfate ions. To monitor the extent of the corrosion in reinforced concrete, it is necessary to recognize and track the diffusion of degradation factors. In this paper, we suggest thin-film iron sensorto measure the penetration of chloride ions. The sensor indicates results as electrical resistance and change in electrical resistance. The sensor and contact pad are connected by an anisotropic conducting film (ACF) bonding in order to reduce the influence of the contact electrical resistance. The sensor’s electrical resistance increases with corrosive behavior and external chloride ion concentration. Use of these thin-film iron sensors enables measurement and monitoring of the depth of chloride ion diffusion in concrete.

Recently, Advanced water treatment facilities with Ozone are being introduced domestically. However, waterproofing/corrosion prevention construction method of concrete structure for existing advanced water treatment makes waterproofing/corrosion prevention materials and concrete deteriorated because of strong oxidation of ozone. Therefore, in this study, As a one of studies for improving durability of advanced water treatment plant applied by metal spray system, electrochemical corrosion protection of metal spraying film according to surface treatment in pH 5 acid solution which is similar to pH concentration in real ozone treatment was evaluated..

Development of appropriate construction technology at frozen soil environments for developing resources is essential. However, cathodic protection technology using monitoring at frozen soil environments is lack. In this study, we want to build a real-time monitoring system at frozen soil environments through corrosion monitoring using type of gavanic metal

This study is based on the electrochemical theory which aims to get the quantitative evaluation about corrosion protection of Zn-Sn metal spray method. The various existing corrosion resistance method and various mixture ratio of Zn-Sn metal spray method is applied with structural steel which is measured change of polarization resistance and corrosion potential. So corrosion protection of Zn-Sn metal spray method is tested. Consequently, coating side of Zn-Sn metal spray method was lower than electric potential of a structural steel adhesion side. So, Galvanic Protection of Zn-Sn metal spray found that structural steel advanced system. Accordingly, Zn-Sn metal spray method is expected as corrosion protection technology excellent in corrosion prevention of structural steel.

The purpose of this study is to evaluate the corrosion protection properties of Zn/Sn metal spray method according to the contents ratio of Zn and Sn by CASS test. Also, the corrosion protection life of Zn/Sn metal spray method is evaluated by the comparing between the corrosion properties of Zn metalizing method and Zn/Sn metal spray method using CASS test. As a result, it was confirmed that the optimum content ratio of Zn/Sn in metal spray method is 60:40(65:35) (Zn : Sn volume ratio) in aspect of corrosion protection properties and construction properties. Also, it was confirmed that the Zn/Sn metal spray method had more than 3 times of corrosion protection properties cmparing the Zn matalizing method.

강구조물의 고력볼트 마찰접합부에 있어서 마찰면의 부식은 장기적으로 마찰력 감소와 접합부 내력저하를 초래한다. 본 연구는 고력볼트 접합부의 부식을 방지하고 소요 역학적 성질을 만족시키기 위해 접합부의 마찰면에 Zn/Al 금속용사 방청처리 한 고력볼트 접합부를 대상으로 마찰면의 표면처리방법과 피막두께를 주요 변수로 하여 인장시험을 실시하였고, 실험으로 부터 마찰면 표면거칠기와 미끄럼계수를 측정하였다. 무도장 샌드블라스트 처리한 접합부 및 샌드블라스트 처리 후 금속용사를 실시한 볼트 접합부의 미끄럼 계수는 국내 규준의 규정 값과 비교하여 동등 이상의 우수한 미끄럼계수 값을 나타냈다.