The cooling process in the injection molding requires the longest time. Therefore, a lot of studies have been conducted to reduce the cooling time. In particular, studies on conformal cooling channels using 3D printing are actively being conducted. In this study, the effect of the conformal cooling channel considering the hood shape instead of the conventional linear cooling channel was investigated by injection molding analysis. In the analysis results, when the conformal cooling channel was applied, the length deformation of the molded product was reduced by about 33% and the circular deformation of the hood assembled on the lens was reduced by about 7.1㎛.

The wavy fins have been widely used in the heat exchangers in coolering system, aerospace system and automotive. Especially, an automobile has the wavy fin and flat tube heat exchanger for oil cooling system. The objective of this research is the performance comparison of wavy fins for battle vehicle diesel engine oil-cooler by numerical analysis. The real type fin is the wavy fin with corrugated structure, and the comparative fin surfaces are plain, louver, lateral perforation and parallel wavy fin. The non-dimensional values of f-factor, j-factor, area goodness factor and volume goodness factor was performed on the performance comparison. The plain and louver fin shows the highest performance in pressure drop and heat transfer respectively. In the area goodness factor and volume goodness factor results, the parallel wavy fin and louver fin show the highest values at each result.

원심 해수냉각 펌프를 분석하기 위하여 다른 운전 유량에 대한 캐비테이션 거동을 조사하였다. 3D 2상 해석은 ANSYS-CFX 상 용코드로 수행되었다. 해석에는 k-ε 난류와 Rayleigh-Plesset cavitation 모델이 사용되었다. 수치 예측에 기초하여 세 가지 토출 유량값에 대 하여 헤드 드롭 특성곡선이 작성되었다. 더 높은 유량에서 임펠러는 버블 캐비테이션에 보다 취약하다. 0.7Q, Q 및 1.3Q(Q: 설계 유량)에서 작동하는 펌프의 3 % 헤드 드롭 위치는 각각 NPSHa 1.21 m, 1.83 m 및 3.45 m에 해당한다. 증기 기포의 볼륨이 예측되고 캐비테이션의 위치는 임펠러 내에서 발생하는 캐비티를 시각화하여 예상하였다. 또한, 압력계수와 날개 부하 분포가 구체적으로 제시되어 캐비테이션이 펌프 운전에 미치는 해로운 영향을 나타냈다. 또한, 압력계수 분포와 날개부하 차트가 구체적으로 제시되어, 펌프 운전에 캐비테이션이 미치는 해로운 영향을 나타냈다.

The main purposes of this study were to identify the factors affecting the supercooling property and to improve the possibility of supercooling storage of fruits and vegetables. Freezing point and nucleation temperature, moisture content, hardness, sugar content, and pH of nineteen fruits and vegetables were measured and Pearson correlation analysis was performed. Freezing point showed a statistically significant correlation with moisture content and sugar content (p<0.01), while ice nucleation temperature showed a correlation (p<0.05) only for sugar content. In particular, the water content and sugar content did not show any correlation with the freezing supercooling difference (FSD). From the correlation analysis between FSD, aerobic bacteria, lactic acid bacteria, yeast, and mold, FSD showed a correlation (p<0.01) with aerobic bacteria. The experiments of the saline solutions inoculated with aerobic bacteria at different concentrations showed FSDs of about 2 for saline inoculated with 9.4 log CFU/mL and about 6 for saline inoculated lower than 5 log CFU/mL. Therefore, the aerobic bacteria concentration was determined to be a key factor affecting the supercooling storage of fruits and vegetables.

국내 가동원전 중 2-루프 가압경수로인 고리1호기는 약 40년 운전한 후, 2017년 6월 18일 영구정지되었다. 영구정지된 고리 1호기는 주요 해체작업을 수행하기전에 계통내 선량률을 저감시켜 작업자피폭을 최소화하기 위한 계통제염을 수행할 예정이다. 일반적으로, 계통제염 범위는 원자로압력용기, 가압기, 증기발생기, 화학 및 체적제어계통, 잔열제거계통 및 원자로 냉각재계통 주요배관을 포함한다. 이러한 계통 및 기기 등을 효율적으로 제염하기 위해서는 제염과정에서 원자로냉각재계 통내 유동특성을 평가할 필요가 있다. 계통제염을 위해 순환유량을 제공하는 방법은 다양하나, 본 논문에서는 잔열제거펌프 운전에 따른 고리1호기 원자로냉각재계통내 유동특성을 평가하였다. 잔열제거펌프를 이용한 계통제염은 원자로냉각재 내 유량의 불균형을 초래하여 계통내 기기 및 배관 등에 불순물을 침적시켜 제염이 효율적이지 않다는 것으로 평가되었다.

Currently, the cutting oil supply device is not equipped to cool the cutting oil. Therefore, additional cooling device should be connected to cool the cutting oil. This has the disadvantage of increasing the size of the device and reducing its cooling capability. To overcome these shortcomings, cooling coils are applied to the outside of the cutting oil filtering device to develop a heat exchanger filter for simultaneous coolant filtering and cooling to improve the compactness of the cutting oil supply device and cooling capability of the cutting oil. For the development of heat exchanger filter, flow and heat transfer analysis were performed. Due to the small heat transfer area of 10 cooling coils, less heat exchange occurred. In the 20 cooling coils, the coolant cooling coils prevented smooth flow of the cooling oil in the heat exchanger filter. The cooling efficiency of the 15 cooling coils were best, and the cooling temperature decreased non-linearly as the supply flow rate of the cutting oil increased.

Energy saving in household refrigerators becomes more important as the usage of household refrigerators have been increasing every year. Since a compressor in the refrigerator consumes more than 80% of its total energy, it is necessary to reduce the energy consumption of the compressor. In this paper, the convective heat transfer coefficients on the compressor housing for both natural convection and forced convection were measured. Then, the effect of convective heat transfer coefficient on the power consumption of a refrigerator was investigated using a thermal management analysis. The results showed that convective heat transfer coefficient for forced convection is higher by 7.8 W/m²K compared to the natural convection. In addition, through the thermal management analysis, it was found that the increase in convective heat transfer coefficient reduces the refrigerator power by about 4.8% improving EER by 0.9%.

In the present study the microstructure of low-carbon steels fabricated by controlled rolling and accelerated cooling processes was characterized and identified based on various microstructure analysis methods including optical and scanning electron microscopy, and electron backscatter diffraction(EBSD). Although low-carbon steels are usually composed of α-ferrite and cementite(Fe3C) phases, they can have complex microstructures consisting of ferrites with different size, morphology, and dislocation density, and secondary phases dependent on rolling and accelerated cooling conditions. The microstructure of lowcarbon steels investigated in this study was basically classified into polygonal ferrite, acicular ferrite, granular bainite, and bainitic ferrite based on the inverse pole figure, image quality, grain boundary, kernel average misorientation(KAM), and grain orientation spread(GOS) maps, obtained from EBSD analysis. From these results, it can be said that the EBSD analysis provides a valuable tool to identify and quantify the complex microstructure of low-carbon steels fabricated by controlled rolling and accelerated cooling processes.

For years, many beauty industries have been developed many beauty treatment machines in healthcare. It is respond to increased demand for new health technologies aimed at assisting aging populations, promoting public health, and improving quality of life. The purpose of this study was to develop the cooling treatment machine to be operators in clinical and beauty treatment use. The developed machine can an be helpful for skin soothing treatment of skin care shop and cosmetic surgery in beauty industries.

Although most of the automobile bodies are made of steel, the application of aluminum alloy sheet with high strength is under consideration for the development of environmentally friendly lightweight body for fuel economy improvement and carbon dioxide emission reduction. In the case of some inner plates, application of magnesium alloy sheet is examined. TRB plate has been studied mainly for weight reduction and rigidity reinforcement of steel plate parts. Recently, research on aluminum TRB rolled plate for light and environment friendly automobile application has been started, It is expected that the development of eco - friendly TRB rolling material made of light alloy will increase as the importance of light weight body for future energy efficiency increases. Therefore, in this study, we tried to obtain the technology to improve the quality of the product by pre - verifying the cooling performance of the hot forming process through the heat flow analysis and evaluating the cooling performance through the temperature distribution analysis. As a result, it was found that the temperature distribution through the flow velocity problem and the flow of the cooling channel can influence the quality of the final product through different heat distribution and cooling time depending on the shape of the mold and the product.

This paper aims to reveal the effects of the K- turbulence model on the performance analysis of battery cooling system for electric vehicle. The maximum temperature, the difference of temperature, and temperature distributions on the battery module were compared with and without K- turbulence model under the different flow rate. It can be expected that the maximum temperature of K- turbulence model is corrected by using the average error rate without the result of K- turbulence model.

Warpage of injection molded product is caused by non-uniform shrinkage and residual stress. A method of removing uneven molding shrinkage and residual stress is to remove the defective factor to Uniform cooling of products. Warpages for part designs have been investigated in this study according to the injection molding conditions for amorphous ABS and crystalline PP by the rapid cooling and heating system. Experimental results showed that the crystalline resin was more warped than amorphous resin, Warpages have been observed in the regions of the part, near gate region and flow direction region.

Cutting tools tend to wear gradually with progressing of machining process due to extremely high surface loads and temperature from the relative motions between tool and workpiece. Especially, the high cutting temperature is a dominant factor in the relation to tool life. High-pressure coolant has been reported as an effective method to prevent the severe wear from cutting temperature. This research investigates efficient supplying conditions of high-pressure coolant with the CFD results from a internal-flush drilling process. The flow rate of coolant is increased drastically up to three times under 70 bar compared to conventional way.

This paper aims to reveal the effects of the K-ε turbulence model on the performance analysis of battery cooling system for electric vehicle. The maximum temperature, the difference of temperature, and temperature distributions on the battery module were compared with and without K- ε turbulence model under the different flow rate. It was found that there was no need to apply K-ε turbulence model when the flow rate is over 500m3/h because the difference of maximum temperature is under the 6℃.

The result of the previous work leads to the idea that the inner area of the hyperbolic shell generator should be minimized for the cooling tower with higher first natural frequency. In this study the inner area of the hyperbolic shell generator was graphically established under varying height of the throat and angle of the base lintel. From the graph, several shell geometries were selected and analysed in the aspect of the natural frequency. Three representative towers reinforced differently due to different first natural frequencies were analysed non-linearly and evaluated using a damage indicator based on the change of natural frequencies. The results demonstrated that the damage behaviour of the tower reinforced higher due to a lower first natural frequency was not necessarily advantageous than the others