최대 선출력 61 ㎾/m 및 평균 연소도 1,770 ㎿d/tU의 조건으로 하나로에서 조사한 DUPIC(Direct Use of Spent PWR Fuel in CANDU Reactors) 핵 연료를 EPMA (Electron Probe Micro Analyzer)를 이용하여 핵분열 생성물을 분석하였다. EPMA의 정확한 분석 방법을 확립하고자, 핵분열생성물 대신 시약을 첨가하여 제조한 모의 DUPIC 핵연료로 EPMA 분석을 수행하였고, 그 결과를 습식 화학 분석의 결과와도 비교하여 평가하였다. 모의 DUPIC 핵연료 중심부의 금속 석출물은 약 1 정도의 크기로 관찰되었으며, 이들의 조성은 Mo-53.89 at.%, Ru-37.40 at.% 및 Pd+Rh-8.71 at%이었다. 모의 DUPIC 핵연료 시험에서 정립한 시험방법으로 조사한 DUPIC 핵연료 시편의 금속 석출물 특성을 분석하였다. 핵연료 중앙부에서 관찰된 금속 석출물들의 크기는 2∼2.5 정도이었으며, Mo-47.34 at.%, Ru-46 at.%, Pd+Rh-6.65 at.%의 조성임을 확인하였다. 이 실험을 위하여, 특별히 시료의 전도성을 향상시키기 위한 처리를 하였으며, 작은 금속 석출물에 EPMA의 전자빔을 정확히 조사할 수 있는 실험 조건을 제시하였다.

Pure WC powders which does not include a binder phase were consolidated by spark plasma sintering (SPS) process at 1600~185 for 0~30 min under 50 MPa. Microstructure alid mechanical properties of binderless WC prepared by SPS were investigated. With increasing sintering temperature, sintered density and Vickers hardness of binderless WC increased. The fracture toughness of binderless WC was 7~15 MPa depending on the sintered density and decreased with increasing the Vickers hardness. It is found that the binderless WC prepared by SPS at 175 for 10 min under 50 MPa showed nearly full densification with fine-grained structure and revealed excellent mechanical properties of high hardness (~HV 2400) and considerably high fracture toughness (~7 MPa ).

Aligned multi-wall carbon nanotubes (MWNTs) were synthesized through the catalytic decomposition of hydrocarbons in a quartz tube reactor. In this study, we investigated the influence of reaction parameters such as gas flow rate, ferrocene-xylene ratio and partial pressure, and reaction time on the yield and structure of vertically aligned carbon nanotubes produced by the floating catalyst method. The MWNTs produced had diameters in the range of 20~l00 nm, length around 100μm and bulk density about 0.51g/cm3 at a pressure of l0000 psi. It was possible to produce MWNTs with much faster growth rate of 12μm/min than that reported previously by the increase of ferrocene-xylene partial pressure.

Modification of C/C composite bipolar plate for improving electrical conductivity was carried out by addition of electroconductive carbon black (EC-CB). Carbon black was carefully mixed to methanol-containing phenolic resin, impregnated into 2D-carbon fabrics, hot pressed and then carbonized to obtain composite plate. Inclusion of electro-conductive carbon black enhanced the electrical conductivity of the C/C composites by increasing the conduction path. Addition of 10 vol% carbon black increased the electrical conductivity from 5.5/Ωcm to 32/Ωcm and reduced the crack formation by filling effect, resulting in the increase of flexural properties of composite plate. However, at carbon black content over 10 vol%, flexural properties decreased by delaminating role of excess carbon black at the interface in C/C composites.