검색결과

검색조건
좁혀보기
검색필터
결과 내 재검색

간행물

    분야

      발행연도

      -

        검색결과 5

        1.
        2023.11 구독 인증기관·개인회원 무료
        Republic of Korea is preparing to decommission Kori Unit 1 and Wolsong Unit 1. Decommissioning of a nuclear power plant proceeds in the following stages: shutdown, transition period, decontamination, cutting, waste treatment, and site restoration. When nuclear power plant is decommissioned, It is expected that approximately 80,000 drums of radioactive waste will be generated per nuclear power plant. Therefore, various technologies are being researched and developed to reduce this to approximately 14,500 drums. Technologies for waste volume reduction are largely mechanical and electrical/thermal methods. Representative examples of mechanical volume reduction technologies include super compactors and electrical/thermal volume reduction technologies include induction and plasma torch furnaces. Both technologies are effective reduction technologies, but the reduction ratio varies depending on the type or condition of waste before treatment. For example, as a result of testing waste reduction using a super compactor at NUKEM in Germany, the reduction ratio was found to be between 1.3 and 7 depending on the type or condition of waste such as chips, ash, scrap metal, sand, etc. And according to IAEA-TECDOC-1527, when reducing the volume of metals, aluminum, lead, copper, brass, etc. using induction melting, the waste volume reduction ratio is 5 to 20. In this paper, referring to these results, a melting test was conducted using a previously developed plasma torch with an output of more than 100 kW. And volume reduction characteristics of this plasma torch was considered depending on waste type or condition.
        3.
        2017.05 KCI 등재 서비스 종료(열람 제한)
        본 연구에서는 국내 콘크리트구조기준(2012)에서 규정하고 있는 최소철근량 이하로 보강된 보에 강섬유를 혼입한 강섬유보강철 근콘크리트보의 휨파괴 실험을 수행하였다. 실험변수는 철근비와 강섬유의 혼입량으로 하였다. 철근보강비는 최소철근량의 44%, 66%, 78% 와 100%로 하였으며, 강섬유의 혼입량은 0.25%, 0.50%, 0.75% 및 1.00%이다. 실험결과, 강섬유는 균열저항성능을 크게 개선시키는 것으로 확 인되었다. 또한, 하중저항성능의 관점에서 강섬유는 항복하중의 증가에 기여하지만 극한하중의 증가에는 거의 기여하지 못하는 것을 확인하 였다. 강섬유로 인한 항복하중의 증가량은 철근 감소로 인한 항복하중의 감소량에 비하여 미미한 것으로 나타났다. 최소철근보에서 강섬유의 사용은 오히려 연성을 크게 감소시키는 것으로 확인되었다. 따라서 최소철근 휨부재에 강섬유를 사용하기 위해서는 연성도 확보를 위하여 철 근비를 증가시켜야 하는 것으로 확인되었다.
        4.
        2017.03 KCI 등재 서비스 종료(열람 제한)
        In this experimental study, the characteristic of damages on GFRP rebar exposed to high temperature only and immerged in alkaline solution after the exposure to high temperature was analyzed through microscopic image analysis. The found microcrack and pores in resin matrix were quantitatively compared if there was effect of pre-exposure to high temperature. The damages, such as microcrack and pores in resin matrix, by alkali exposure were mainly found in rebar surface. On the other hand, the pores caused by high temperatures were extensively found in a section and had greater width than those caused by the alkali exposure. In results of the quantitative comparison, the accumulated length and widths of microcrack and pores in resin matrix in pre-exposed GFRP rebar to high temperature were respectively 1.5 and 1.4 times of those in the GFRP rebar only immerged in alkali solution. Therefore, the deterioration of resin matrix by the alkali exposure could be accelerated due to the pre-exposure to high temperature.
        5.
        2015.11 KCI 등재 서비스 종료(열람 제한)
        본 실험 논문은 초단유리섬유(milled glass fibers)가 혼입된 PSC용 그라우트 몰탈의 강재부식성능을 평가하였다. 초단유리섬유를 함유한 배합이 PSC 그라우트 몰탈로서 소요성능을 만족시키는지를 확인하기 위하여 유하시간, 블리딩 및 압축강도를 측정하였다. 초단유리 섬유를 함유한 몰탈의 부식저항 성능은 염소이온 확산시험, 몰탈 흡수시험과 표면전기저항 측정 결과에 근거하여 수행되었다. 시험결과, 초단 유리가 혼입된 모든 배합은 OPC만 사용된 배합에 비하여 그라우트의 부식저항성능을 개선시키는 것으로 확인되었다. 다만, 초단유리섬유를 사용함으로서 유하시간은 단축되지만 블리딩이 발생하여 소요성능을 만족하지 못하는 것으로 확인되었다. 그러므로 PSC 그라우트에 적합한 초단유리섬유배합이 되기 위해서는 물-바인더비의 조정이 필요한 것으로 판단된다.