Domestic commercial low- and intermediate-level radioactive waste storage containers are manufactured using 1.2 mm thick cold-rolled steel sheets, and the outer surface is coated with a thin layer of primer of 10~36 μm. However, the outer surface of the primer of the container may be damaged due to physical friction, such as acceleration, resonance, and vibration during transportation. As a result, exposed steel surfaces undergo accelerated corrosion, reducing the overall durability of the container. The integrity of storage containers is directly related to the safety of workers. Therefore, the development of storage containers with enhanced durability is necessary. This paper provides an analysis of mechanical properties related to the durability of WC (tungsten carbide)-based coating materials for developing low- and intermediate-level radioactive waste storage containers. Three different WC-based coating specimens with varied composition ratios were prepared using HVOF (high-velocity oxy-fuel) technique. These different specimens (namely WC-85, WC-73, and WC-66) were uniformly deposited on cold-rolled steel surfaces ensuring a constant thickness of 250 μm. In this work, the mechanical properties of the three different WCbased coaitng materials evaluated from the viewpoints of microstructure, hardness, adheision force between substrate and coating material, and wear resistance. The cross-sectional SEM-EDS (Scanning Electron Microscope-Energy Dispersive X-ray Spectroscopy) images revealed that elements W (tungsten), C (carbon), Ni (nickel), and Cr (chromium) were uniformly distributed within the each coating layers which was approximately 250 μm thick. The average hardness values of HWC-85 and HWC-73 were found to be 1,091 Hv (Vickers Hardness) and 1,083 Hv, respectively, while the HWC-66 exhibited relatively lower hardness value of 883 Hv. This indicates that a higher WC content results in increased hardness. Adhesion force between and substrates and coating materials exceeded 60 MPa for all specimens, however, there were no significant differences observed based on the tungsten carbide content. Furthermore, a taber-type abrasion tester was used for conducting abrasion resistance tests under specific conditions including an H-18 load weight at 1,000 g with rotational speed set at 60 RPM. The abrasion resistance tests were performed under ambient temperatures (RT: 23±2°C) as well as relative humidity levels (RH: 50±10%). Currently, the ongoing abrasion resistance tests will include some results in this study.

This study focuses on the development of coatings designed for storage containers used in the management of radioactive waste. The primary objective is to enhance the shielding performance of these containers against either gamma or neutron radiation. Shielding against these types of radiation is essential to ensure the safety of personnel and the environment. In this study, tungsten and boron cabide coating specimens were manufactured using the HVOF (High-Velocity Oxy Fuel) technuqe. These coatings act as an additional layer of protection for the storage containers, effectively absorbing and attenuating gamma and neutron radiation. The fabricated tungsten and boron carbide coating specimens were evaluated using two different testing methods. The first experiment evaluates the effectiveness of a radiation shielding coating on cold-rolled steel surfaces, achieved by applying a mixture of WC (Tungsten Carbide) powders. WC-based coating specimens, featuring different ratios, were prepared and preliminarily assessed for their radiation shielding capabilities. In the gamma-ray shielding test, Cs-137 was utilized as the radiation source. The coating thickness remained constant at 250 μm. Based on the test results, the attenuation ratio and shielding rate for each coated specimen were calculated. It was observed that the gammaray shielding rate exhibited relatively higher shielding performance as the WC content increased. This observation aligns with our findings from the gamma-ray shielding test and underscores the potential benefits of increasing the tungsten content in the coating. In the second experiment, a neutron shielding material was created by applying a 100 μm-thick layer of B4C (Boron Carbide) onto 316SS. The thermal neutron (AmBe) shielding test results demonstrated an approximate shielding rate of 27%. The thermal neutron shielding rate was confirmed to exceed 99.9% in the 1.5 cm thick SiC+B4C bulk plate. This indicates a significant reduction in required volume. This study establishes that these coatings enhance the gamma-ray and neutron shielding effectiveness of storage containers designed for managing radioactive waste. In the future, we plan to conduct a comparative evaluation of the radiation shielding properties to optimize the coating conditions and ensure optimal shielding effectiveness.

There are many types of foam molding methods. The most commonly used methods are the pressure foaming method, in which foam resin is mixed with a foaming agent at high temperature and high pressure, and the normal pressure foaming method, which foams at high temperature without pressure. The polymer resins used for foaming have different viscosities. For foaming under normal pressure, they need to be designed and analyzed for optimal foaming conditions, to obtain resins with low melt-viscosity or a narrow optimal viscosity range. This study investigated how changes in viscosity, molding temperature, and cross-link foaming conditions affected the characteristics of the molded foam, prepared by blending rubber polymer with biodegradable resin. The morphologies of cross sections and the cell structures of the normal pressure foam were investigated by SEM analysis. Properties were also studied according to cross-link/foaming conditions and torque. Also, the correlation between foaming characteristics was studied by analyzing tensile strength and elongation, which are mechanical properties of foaming composites.

We demonstrated an effective way of preparing melt spinnable mesophase pitches via catalytic hydrogenation of petroleum residue (fluidized catalytic cracking-decant oil) and their subsequent thermal soaking. The mesophase pitches thus obtained were analyzed in terms of their viscosity, elemental composition, solubility, molecular weight, softening point and optical texture. We found that zeolite-induced catalytic hydrogenation under high hydrogen pressure contributed to a large variation in the properties of the pitches. As the hydrogen pressure increased, the C/H ratio decreased, and the solubility in n-hexane increased. The mesophase pitch with entirely anisotropic domains of flow texture exhibited good meltspinnability. The mesophase carbon fibers obtained from the catalytically hydrogenated petroleum residue showed moderate mechanical properties.

Cryopreservation of avian semen is a useful tool to preserve genetic resource for aim of preventing extinction induced by infectious disease like avian influenza. Unlike those of mammals, data from chicken cryopreserved semen has not been showed feasible results. So, various cryoprotectants and diluents have been examined in many methods. In this report, as a major ingredient of avian seminal plasm, glutamine was substituted by alanyl glutamine to enhance physiological stability of chicken semen during freezing. We studied effect of glycerol and Dimethylacetamide(DMA) on motility and progressive motility of spermatozoa using glutamine diluent(EK-G) or alanyl glutamine diluent(EK-A) condition. The semen of Ogye was collected twice a week by the dorso-abdominimal massage method and diluted with same volume of EK-G or EK-A at 25℃ and stored for 10 min at 4℃ in cold chamber. Glycerol or DMA was added to diluted semen to reached 7% of final concentration at 4℃. After 3min of equilibration, the diluted semen was packed into 0.25ml straws and subjected to cryopreservation used freezing equipment. The packed straw were placed on height 5 cm above surface of liquid nitrogen(LN2) and held for 10min. After preserved for 2 weeks, the straw was thawed onto the 4℃ cooling bath. The images of motility and progressive motility spermatozoa were recorded by digital image recorder and analyzed by manual. The results showed 68.5% motility and 34.1% progressive motility in DMA/EKA diluent, 31.45% and 17.6% in glycerol/EKA, 45.4% and 8.6% in DMA/EKG, and 9.7% and 6.4% in glycerol/EKG. With these results, the alanyl glutamine and DMA could be used as a main composition of diluent and cryoprotectant for cryopreservation of chicken semen.

Advanced multidetector CT (MDCT) technology provides 2-dimensional (2D) images with 3-dimensional (3D) images. These 3D images (volume rendered, VR images) demonstrates the surface of the body and cutaneous neurofibromas in pa-tients with neurofibromatosis (NF) are well visualized. MDCT is a very useful imaging modality that represents various findings of neurofibromatosis such as cutaneous neurofibromas, central nervous tumors, skeletal anomalies including verte-bral scalloping and dural ectasia, mediastinal masses, lung parenchymal diseases, vascular anomalies, and complicated dis-eases related with NF. Herein, we report three cases with NF presenting cutaneous neurofibromas diagnosed by MDCT; One is NF patient with dural ectasis and meningocele, second case is a patient with NF and horseshoe kidney, third case is a pa-tient with cutaneous and subcutaneous neurofibromas.

This experiment was conducted to investigate the variation of nitrogen use efficiency, nitrogen uptake efficiency, physiological utilization efficiency and their relationships with growth characteristics in the 28 Korean rice cultivars. Nitrogen use efficiency of 28 rice cultivars was 47.74, nitrogen uptake efficiency was 0.71, and physiological utilization efficiency was 68.76 in average. Nitrogen use efficiency of rice cultivars had low variation ranged from 44.09 to 51.91, but nitrogen uptake efficiency were relatively high variation from 0.51 to 0.90, and physiological utilization efficiency was from 51.71 to 94.26. The high efficient group in nitrogen uptake efficiency whose value was calculated above 0.80 included Daeanbyeo, Seojinbyeo, Ansungbyeo, Dongjinbyeo, and Hwaanbyeo, while the low efficient group with below 0.60 was Kwanganbyeo, Sampyeongbyeo, Soorabyeo, and Hwasungbyeo. Hwasungbyeo, Sampyeongbyeo, Soorabyeo for physiological utilization efficiency were more efficient cultivars, while Daeanbyeo, Seojinbyeo, Ansungbyeo were less efficient cultivars. Nitrogen uptake efficiency had positive correlation coefficients between dry matter weight of plant (0.842** ), leaf area index (0.761** ), and leaf nitrogen content (0.599** ), respectively. Therefore, the dry matter weight of rice plant and leaf area index was important characters to evaluate nitrogen uptake efficiency in rice cultivars. Also, more efficient cultivar in nitrogen uptake had higher chlorophyll meter value, which was appeared dark green color.