One of released radioactive gases from a spent fuel is cesium (137Cs) as semi-volatile fission products and reticulated ceramic foam could be used for capturing the gaseous cesium. It has threedimensional open-pore structures and consumes cesium above 600°C to form cesium species including Cs-nepheline (CsAlSiO4) and pollucite (CsAlSi2O6) phases. Kaolinite-based foam filter is a favorable ceramic filter because they exhibit superior capture characteristics compared to other aluminosilicate minerals and other shape filters. However, for usage in special conditions, structural limitations such broken struts must be improved. Here, recoating by using centrifugation, followed by a pre-sintering cycle was conducted for covering the cracks and voids, resulting from the burnout of the polyurethane sponge as a sacricial template. The slurry including additives was chosen by considering viscous behavior of slurries for the centrifugation. The microstructure and strength was improved by the recoating.

Reticulated foams have a continuous skeleton network consisting of aluminosilicates and are used for capturing gaseous cesium released from spent nuclear fuel at high temperature. It has high stability to high temperature and good capturing performance. Homogeneous cell distribution and modified surface structures are indispensable conditions for stable operation and handling. In particular, triangularly shaped holes inside the struts were generated during the pyrolysis of polyurethane sponge as a sacricial template, which lead to limite the strength of the reticulated foam as well as cracks. However, several attempts have been focused on the increasing the strut thickness. Here, we have prepared ceramic foams by the polyurethane sponge replication method with roller squeezing. Ceramic slurry including additives was determined with consideration of its viscous behavior. After pre-sintering, infiltration under vacuum was conducted. Metakaolin slurry was filled partially into the triangular void. As a result, the compression strength was improved by structure modification without composition change.

The potential use of cost-effective carbon anodes, as an alternative to expensive platinum, in the reduction of oxides within LiCl-Li2O molten salt at elevated cell potentials presents a promising avenue. However, this elevated potential gives rise to the generation of a complex mixture of anodic gases, including hazardous and corrosive species such as chlorine (Cl2), oxygen (O2), carbon monoxide (CO), and carbon dioxide (CO2). In this study, we investigate the influence of applied potential and salt composition on the composition of the generated gas mixture. Real-time gas analysis was conducted during the TiO reduction reaction in the molten salt at 650°C using a MAX-300-LG gas analyzer. Simultaneously, electronic signals, including current, potential, and salt composition, were monitored throughout the oxide reduction process. Additionally, XRD investigations were performed to verify the crystal structure of the resulting products. This research provides valuable insights into optimizing carbon anode-based reduction processes for improved efficiency and safety.

Pyroprocessing is a crucial method for recovering nuclear fuel materials, particularly uranium and transuranic elements (TRU), through electrochemical reactions in a LiCl or LiCl-KCl molten salt system, which is highly stable medium at elevated temperatures. In the electrochemical reduction stage, actinide metal oxides are effectively transformed into their metallic forms and retained at the cathode within a molten LiCl-Li2O environment at 650°C. Simultaneously, oxygen ions (O2-) are generated at the cathode and then transported through the molten salt to be discharged at the anode, where they combine to form oxygen gas (O2) on the anode’s surface. One notable challenge in this electrochemical process is the generation of various byproducts during the anode oxide reduction step, including oxygen, chlorine, carbon dioxide, and carbon monoxide. Consequently, significant amounts of corrosion products tend to accumulate on the upper region of the anode’s immersion area over time. This report introduces a novel solution to mitigate corrosion-related challenges within the specified temperature range. We propose a selective oxidation treatment for the NiCrAl-based 214 Haynes alloy, involving exposure to 1,100°C in a reducing atmosphere. The objective is to stimulate the growth of protective α-Al2O3 scales on the alloy’s surface. The resulting oxide scales have undergone thorough characterization using SEM, EDS, and XRD techniques. The pre-grown alumina scale has demonstrated commendable adherence and thermal stability, even when subjected to a chlorine-oxygen mixed atmosphere at the specified temperature.

This study examined the heat balance in the electrolytic reducer during oxide reduction of pyroprocessing. The adoption of carbon anodes instead of conventional platinum anodes in the oxide reduction process has made it possible to apply high currents, and it has been observed that the temperature of the molten salt of in the reactor rises rapidly when applying high currents, so it is important to maintain an optimal operational temperature range. In this study, salt resistant heat, reaction heat, and decay heat were identified as factors affecting heat balance during the operation of oxide reduction process. Equations describing the relationships among these factors were established. Then using this, a correlation was developed to understand the relationship between applied current and the molten salt temperature in the reactor observed in the actual operation of the carbon anode electrolytic reducer of KAERI. Furthermore, this study proposed strategies to mitigate excessive temperature elevation during oxide reduction operation. A comparative assessment of these approaches was conducted. Considering KAERI electrolytic reducer operation environment, among the considered cooling strategies, the cooling effectiveness was calculated to be highest in the following order: heat transfer to extra salt, convection, conduction, argon gas bubbling.

Since 1997, the Republic of Korea (ROK) has been developing pyro-processing (Pyro) technology to reduce the disposal burden of high-level radioactive waste by recycling spent nuclear fuel (SNF). Compared to plutonium and uranium extraction process, Korean Pyro technology has relatively excellent proliferation resistance that cannot separate pure plutonium owing to its intrinsic characteristics. Regarding Pyro technology development of ROK, the Bush administration considered that Pyro is not reprocessing under the Global Nuclear Energy Partnership, whereas the Obama administration considered that Pyro is subject to reprocessing. However, the Bush and Obama administrations did not allow ROK to conduct full Pyro activities using SNF, even though ROK had faithfully complied with international nonproliferation obligations. This is because the US nuclear nonproliferation policy to prevent the spread of sensitive technologies, such as enrichment and reprocessing, has a strong effect on ROK, unlike Japan, on a bilateral level beyond the NPT regime for non-proliferation of nuclear weapons.

When the recycling technology of spent nuclear fuels (SNF) for future nuclear reactor systems and the treatment technology of SNF for disposing of in a disposal site use a molten salt such as LiCl-KCl eutectic as a processing medium one of the essential unit processes is a distillation process that remove the salt component mixed with fission products recovered. Especially, in case of Pyro-SFR recycling system the recovered nuclear fuel materials such as U, TRU and some of rare earths come from main three processes (electro-refining, electro-winning, and drawdown processes) for recycling of SNF. These recovered fuel materials contain large portion of molten salt or liquid cadmium which requires removal of them by distillation. In spent nuclear fuels discharged from PWR the portion of composing element is as follows. Uranium is about 95%, other actinides such as transuranic elements (TRU; Np, Pu, Am, Cm) is about 1%, the rare earths (lanthanides) is about 1%, and the other elements is about 3%. For example, americium (Am) in the recovered fuel materials has a problem that the reported loss of Am inevitably occurs during the vacuum salt distillation operation. A new segregation method of AMM (actinide metal mixture)–salt system is based on the difference in melting point of the actinide elements. It is possible to apply this segregation method to recovering other actinides from AMM with accompanied salt because of relatively large amount and lower melting point of a specific element in other actinides avoiding vacuum salt distillation. This new segregation method successfully tested using a surrogate element such as aluminum due to its similar melting point with a specific element. The segregation principle is solid-liquid separation, thus the solidified actinides mixture ingot can take out of a molten salt medium.

When damaged nuclear fuel is stripped and re-fabricated into stabilized pellets, it is necessary to analyze the characteristics of the stabilized pellets, such as density, leaching behavior, and compressive strength, for final disposal. In this study, simulated nuclear fuel with UO2 and burn-up of 35 GWd/tU and 55 GWd/tU was used to measure the compressive strength of the stabilization pellet. In order to change the density of the sintered pellet, a sintered pellet was prepared by heat treatment at 1,550°C and 1,700°C for 6 hours in a reducing atmosphere of 4% H2/Ar. In the case of UO2, the density was 10.4 g/cm3 (94.5% of T.D.) and 10.6 g/cm3 (96.6% of T.D.) depending on the sintering temperature (1,550°C, 1,700°C). In the case of simulated fuel with a burn-up of 35 GWd/tU, the density was 8.8 g/cm3 (80.9% of T.D.) and 10.2 g/cm3 (93.6% of T.D.) depending on the sintering temperature (1,550°C, 1,700°C). In the case of simulated fuel with a burn-up of 55 GWd/tU, the density was 8.3 g/cm3 (77.0% of T.D.) and 10.0 g/cm3 (92.3% of T.D.) depending on the sintering temperature (1,550°C, 1,700°C). It was found that the compressive strength of simulated nuclear fuel decreased with increasing burn-up and increased with increasing density. In the case of UO2, the compressive strengths were 717.8 MPa and 897.4 MPa when the densities were 10.4 g/cm3 and 10.6 g.cm3, respectively. In the case of simulated nuclear fuel with a burn-up of 35 GWd/tU, the compressive strengths were 472.1 MPa and 732.3 MPa when the densities were 8.8 g/cm3 and 10.2 g/cm3. In the case of simulated nuclear fuel with a burn-up of 55 GWd/tU, the compressive strengths were 301.4 MPa and 515.5 MPa when the densities were 8.3 g/cm3 and 10.0 g/cm3, respectively.

Instead of using expensive platinum, carbon anodes could potentially be utilized in the process of reducing oxides in LiCl-Li2O molten salt at a high cell potential. However, this high potential leads to the generation of a mixture of anodic gases containing toxic and corrosive gases such as chlorine (Cl2), oxygen (O2), carbon monoxide (CO), and carbon dioxide (CO2). To better understand this gas mixture, we conducted real-time analyses of the gases generated on the carbon anode during the TiO reduction reaction in the molten salt at 650°C, using a MAX-300-LG gas analyzer. Our results indicate that the ratio of CO/O2/CO2/Cl2 in the gas mixture is significantly influenced by the composition of the salt, and that removing the sources of oxygen ions in the salt increases the likelihood of generating toxic and corrosive Cl2 gas.

A new sesame variety 'Namback'was developed at the National Crop Experiment Station through a cross between commercialiy utilized varieties of high yielding 'Danbackkae' and late seeding of second cropping daptable 'Chinjukkae' at 1989 and had been select