Dispersion of the functionalized multiwalled nanotubes (MWNT) in the polyurethane (PU) matrix and DC conductivity of the MWNT/PU composites are investigated with the oxidation conditions, the kind of surfactants and their content. First, the most optimal surfactant type and its critical micelle concentration in the MWNT suspension are determined as a cationic surfactant, benzalkonium chloride (BKC) of 0.6 wt.% to the MWNT content from DEA and FESEM results. All the MWNT oxidized under several conditions are negatively charged and functionalized with carboxylic group, whereas the degree of damage is different from oxidation conditions. In addition, each MWNT/PU composite derived from several oxidation conditions shows different DC conductivity at a characteristic MWNT content. It is found that in order to enhance DC conductivity of the polymeric composites containing the oxidized MWNT the better dispersion of MWNT should be obtained by effective functionalities and surfactant adsorption with preserving the intrinsic geometry of pristine MWNT.

Carbon materials such as graphite and graphene exhibit high electrical conductivity. We examined the electrical conductivity of synthetic and natural graphene powders after the chemical reduction of synthetic and natural graphite oxide from synthetic and natural graphite. The trend of electrical conductivity of both graphene (synthetic and natural) was compared with different graphite materials (synthetic, natural, and expanded) and carbon nanotubes (CNTs) under compression from 0.3 to 60 MPa. We found that synthetic graphene showed a marked increment in electrical conductivity compared to natural graphene. Interestingly, the total increment in electrical conductivity was greater for denser graphite; however, an opposite behavior was observed in nanocarbon materials such as graphene and CNTs, probably due to the differing layer arrangement of nanocarbon materials.

The role of Cl channels in regulatory volume decrease (RVD) in human salivary gland acinar cells was examined using a whole-cell patch clamp technique. Human tissues were obtained from healthy volunteers or from patients with oromaxillofacial tumors. During the measurements, K+-free solutions were employed to eliminate contamination of whole-cell conductance by K+ currents. When the cells were exposed to a 70% hypotonic solution, outward-rectifying currents, which were not observed in the resting state, were found to have significantly increased both in human labial and parotid gland acinar cells. The amplitudes of the currents were reduced in a low CI bath solution. Furthermore, the addition of 100μM 5-Nitro-2- (3-phenyl propylamino) benzoic acid (NPPB) or 100μM 4,4'-diisothio cyanatostilbene-2,2'-disulphonic acid (DIDS), known to partially block Cl channels, significantly inhibited these currents. Its outward-rectifying current profile, shift in reversal potential in a low Cl bath solution and pharmacological properties suggest that this is a Cα2+ independent, volume activated Cl current. We conclude therefore that volume activated Cl channels play a putative role in RVD in human salivary gland acinar cells.

This study was investigated on antioxidant activities of methanol, ethanol, and water extracts of 42 herbs. The herbs grown at Dankook university practice greenhouse. Through the examination of methanol, ethanol , and water extracts from 42 herbs for radical scavenging effects using DPPH method. Antioxidant activities of each solvent extracts were not similar or lower than that ascorbic acid. The IC50 value of antioxidant activities have range 400-200 in about 25% of herbs and water extract showed higher antioxidant activity more than methanol and ethanol extracts. Antioxidant activities in methanol extract were in order of lemon balm>pappermint>oregano, ethanol extract of sweet majoram>oregano>spearmint, and water extract of beramot mixed>lemon balm> oregano. Lemon balm, oregano, red basil , spearmint among 42 herbs showed the highest antioxidive activity and water extract was excellent results than other extracts.

Carbon molecular sieve (CMS) membranes were prepared by pyrolysis of polyimides having carboxylic acid groups and applied to the hydrogen separation. The polymeric membranes having carboxylic acid groups showed different steric properties as compared with polymeric membranes having other side groups (-CH3 and -CF3) because of the hydrogen bond between the carboxylic acid groups. However, the microporous CMS membranes were significantly affected by the decomposable side groups evidenced from the wide angle X-rat diffraction, nitrogen adsorption isotherms, and single gas permeation measurement. Furthermore, the gas separation properties of the CMS membranes were essentially affected by the pyrolysis temperature. As a result, the CMS membranes Prepared by Pyrolysis of polyimide containing carboxylic acid froups at 700℃ showed the H2 permeability of 3,809 Baller [1×10-10 H cm(STP)cm/cm2.s.cmHg], H2/N2, selectivity of 46 and H2/CH4 selectivity of 130 while the CMS membranes derived from polyimide showed the H2 permeability of 3,272 Barrer, H2/N2 selectivity of 136 and H2/CH4 selectivity of 177.

The effects of fiber surface-treatment and sizing on the dynamic mechanical properties of unidirectional and 2-directional carbon fiber/nylon 6 composites by means of dynamic mechanical analysis have been investigated in the present study. The interlaminar shear strengths of 2-directional carbon/nylon 6 composites sized with various thermosetting and thermoplastic resins are also measured using a short-beam shear test method. The result suggests that different surface-treatment levels onto carbon fibers may influence the storage modulus and tan δ behavior of carbon/nylon 6 composites, reflecting somewhat change of the stiffness and the interfacial adhesion of the composites. Dynamic mechanical analysis and short-beam shear test results indicate that appropriate use of a sizing material upon carbon fiber composite processing may contribute to enhancing the interfacial and/or interlaminar properties of woven carbon fabric/nylon 6 composites, depending on their resin characteristics and processing temperature.

Polyvinylpyrrolidone을 포함하는 폴리이미드 전구체의 열분해 공정을 통해 탄소분자체막을 제조하였으며 열분해성 고분자를 포함하는 전구체를 통해 제조된 막의 구조 및 기체 투과 특성에 대해 연구 하였다. 열분해성 고분자를 포함하는 전구체의 열적 특성을 조사한 결과 열적으로 안정한 폴리이미드의 경우 550℃에서 분해되는 것을 확인할 수 있었으며 열분해성 고분자의 경우 400℃에서 분해가 시작되는 것을 TCA를 통해 확인하였다 제조된 탄소분자체막의 기체 투과 특성을 조사한 결과 최종 열분해 온도가 증가됨에 따라 기체 투과도는 감소하였으며 열분해성 고분자를 포함한 전구체로부터 제조된 탄소분자체막의 경우 기체 투과가 향상됨을 알 수 있었다. 열분해성 고분자를 함유하는 전구체로부터 550℃에서 열분해를 통해 제조된 탄소분자체막의 경우 O2 투과도 808 Barrer [10-10cm3 (STP)cm/cm2scmHg]과 O2/N2선택도 7을 나타내었다.