지속적인 선박 대형화와 지구온난화로 인한 해수면 상승으로 항만 내 위험이 증가함에 따라 부두의 마루높이 기준은 상향되는 것이 미래지향적이다. 본 연구에서는 선박 대형화로 인해 풍압면적이 커지므로 마루높이 상향이 필요할 것으로 판단되는 크루즈선과 컨테이너선을 선정하고, 마루높이 상승에 따른 대상부두를 모델링하여 계류 및 동요 안전성을 평가하였다. GT 10만톤급 크루즈선은 풍향이 접안 현 선수방향 45°일 때 풍속 30 kts, H₁조건에서 계류삭 허용파단력이 초과하였다. 또한 부두와 계류삭의 앙각은 마루높이 H₂에서 권고값을 초과하는 것으로 분석되어 최저 마루높이 기준을 H₃로 조정할 필요가 있는 것으로 분석되었다. DWT 10만톤급 컨테이너선은 풍향이 접안현 정횡일 때 마루높이 H₁에서 Sway 운동의 한계값을 초과하는 것으로 분석되어 최저 마루높이 기준을 H₂로 조정할 필요 있는 것으로 분석되었다. 본 연구 결과는 선박 특성을 반영한 부두 마루높이 기준을 제안하기 위한 기초 자료로 활용될 수 있을 것으로 기대된다.

The improvement of resistance performance for the 4.99 ton class fishing boats was shown. The 4.99 ton fishing boats are the most commonly used one in the Korean coastal region. The evaluation of resistance performance was estimated by the Computational Fluid Dynamics (CFD) analysis. The CFD simulation was performed by the validation for various types of bow shapes on the hull. The optimized hull form from the simulation was selected and showed the best resistance performance. This hull type was tested on the towing tank in the National Institute of Fisheries Science (NIFS). The effective horsepower (EHP) was estimated by the resistance test on the towing tank with the bare hull condition. The drag force on the three service speed conditions was obtained for the resistance analysis to power prediction. The measured drag forces are compared with the results from the CFD simulation with one another. As results of the model tests, it was confirmed that the shape of the bow is an important factor in the resistance performance. The effective horsepower decreased about 30% in comparison with the conventional hull form. Also, the resistance performance improved the reduction of required horsepower, which especially contributed to the energy-saving for the fisheries industry. In the CFD analysis, the resistance performance improved slightly. In this case, the ratio of the residual resistance (CR) in the total resistance (CT) was high. Therefore, the CFD analysis was not enough to satisfy with reflection for the free surface and wave form in the CFD procedure. Both model test and CFD calculation in this study can be applied to the initial design process for the coastal fishing vessel.

본 연구에서는 고속으로 활주하는 선박의 승선감 향상 및 운항성능 특성 연구를 위해 30ton급 세관감시정의 측정위치에 따른 멀미도 해석을 수행하였다. 특히, 관공선내의 선원들은 유사시에 신속·정확한 판단이 요구되므로 측정위치에 따른 멀미도의 영향에 대한 연구가 필요할 것으로 판단하였다. 멀미도 평가는 ISO 2631-3(1985)을 기준으로 하였다. 평가 기준은 30분, 2시간, 8시간 이후 성인 100명 중 10명이 멀미를 한다 는 국제표준 지표이며 조우주파수와 수직가속도 성분으로 나타난다. 멀미도 해석은 Maxsurf Motion 모듈을 이용하였다. 30ton급 세관감시정은 고속활주형 선박의 특성을 갖기 때문에 선속에 따른 트림변화를 고려하였다. 입사각은 선체 전 방향에서의 영향을 고려한 범위로 선정하였다. 선 속의 경우 선박 운용상태(정박, 저속, 고속)을 고려하여 적용하였다. 측정위치의 경우 선원들의 주 활동 구역을 고려하여 선정하였다. 해석결과 멀미도의 영향은 30knot, 180°의 경우에 가장 크게 분석되었다.

In this study, a new designed propeller was applied on 24 ton class squid jigging vessel to reduce of fuel consumption. The selected squid jigging boat was under construction at the shipyard to determine the resistance of the hull through the model experiment. The propeller design was carried out by using the experimental data and ITTC procedures. Sea trials were performed by measuring the speed and the horsepower required by the condition of five power levels of engine load, namely 70%, 80%, 90%, MCR and maximum engine power. The speed and delivered horse power were compared between the conventional propeller and the new design propeller. Delivered horse power by installing the new propeller takes 90% engine load at start-up conducted by decreased 9.06%. The measuring speed is increased up to the 0.6 knots in the low-speed range to high range. This study showed that only the design and installation of a new propeller can improve the propulsion efficiency of the boats; furthermore, reduce fuel costs can be achieved at the same time by improving the increased cruising speed.

This study deals with optimized structural analysis of stainless rectangular water reservoirs with 5,000ton capacity for various combined load cases. The objective of this study is to propose most efficient structural models through the comparison of various model cases. In order to perform an optimized analysis, three dimensional finite element analyses are carried out for large sized models. The numerical results obtained provides the detailed size and thickness for optimal design of water reservoir. In particular, results reported in this paper show the influence of various types of loading and dimensions of the wall and stiffened column on the structural behavior of the large sized water tanks.

본 논문에서는 Goal-Driven Optimization(GDO)을 바탕으로 한 양방향 차도선의 차량갑판의 구조설계에 대하여 최적화를 수행하였다. 차량갑판의 강도와 변형에 대한 영향을 검토하여 경제적 비용을 절약할 수 있는 최적점을 결정하였다. 실험계획법(DOE)과 반응표면법을 바탕으로 한 갑판두께를 110% 증가시켜 차량갑판의 강도와 강성을 높일 수 있었다. 이 결과에 대한 회귀분석을 수행하여 3차 다항식 모형인 최적 회귀모형식으로 제안하며 결정계수 R² 0.98정도로 나타내어 신뢰성을 확보할 수 있었다.

The finite element analysis of large sized rectangular water tank structures made of stainless steel materials is carried out for various combined load cases. The combined load cases for a large size of 5,000ton are further determined using the specification(KS B　6283) established from the Korean Standards Association. For the better numerical efficiency, the rectangular panels are modelled using the ANSYS program. The numerical results obtained for different load cases show as follows. In order to resist the snow load, it takes the influence of the gap than the size of the column. Also, in order to resist the water pressure, it shall increase the thickness of the wall. But, increasing the thickness of the wall is considerably less economical. Therefore, the angle with big thickness should be placed right next to the wall.

This study is intended to provide navigator with specific information necessary to assist the avoidance of collision and the operation of ships to evaluate the maneuverability of dead weight tonnage 8,000 tons Oil/Chemical tanker. The actual maneuvering characteristics of ship can be adequately judged from the results of typical ship trials. Author carried out sea trials based full scale for turning test, Z” maneuvering test, man overboard rescue maneuver test, inertia stopping test. Consequently, 2st Overshoot yaw angle of the semi balanced rudder and flap rudder in ±20° zig–zag test showed 22.2° and 18.0°, respectively. The maneuverability of the vessel was good in the flap rudder. The man overboard rescue maneuver maneuverability test was most favorable in the flap rudder and the full load condition. The results from tests could be compared directly with the standards of maneuverability of IMO and consequently the maneuvering qualities of the ship is full satisfied with its.

This study is intended to provide navigator with specific information necessary to assist the avoidance of collision and the operation of ships to evaluate the maneuverability of dead weight tonnage 8,000 tons Oil/Chemical tanker. The actual maneuvering characteristics of ship can be adequately judged from the results of typical ship trials. Author carried out sea trials based full scale for turning test in ballast condition and full load condition, semi balanced rudder and flap rudder. The turning circle maneuvering were performed on the starboard and port sides with 35° rudder angle at the normal continuous rating. The results from tests could be compared directly with the standards of maneuverability of IMO and consequently the maneuvering qualities of the ship is full satisfied with its.

육지와 도서를 연결하는 차도선은 교통수단 기능과 물자수송을 담당하는 중요한 역할을 하고 있다. 이에 따라 차도선의 효율성 증대와 안전성 향상 및 경제적 요건 등을 고려한 선박이 개발 중이다. 유럽에서는 승객의 편의성 및 경제성을 고려하여 양방향 차도선(Double-ended Car Ferry)의 개발이 활발히 진행 중이며 국내에서도 이에 대한 연구 개발이 필요하다. 본 연구에서는 유한요소법을 이용하여 차도선 제작 시 축계의 제작 및 강도의 문제를 Campbell Diagram 및 Modal 해석을 통한 동특성 분석을 하였다. 이를 통하여 양방향 차도선의 추진 방향 및 후진 방향 축계 작동 시 공진 현상 및 위험속도를 분석 결과 안정성을 보인 것으로 판단된다.

This study describes the result on PV system for evaluating the performance of small fishing boats. Photovoltaic system with 200 watts power generation facilities on the 3-ton fishing boat was carried. Load test was performed on the condition that the work lamps lit during night operations. As a result the performance can be used for more than two hours at 60 watt work lamps. The load test was performed on the condition that fishing vessels are on the cruising condition at sea. The solar power systems have been investigated as a power generation efficiency of about 36.55%. Additional tests show that the power generation efficiency is difficult to expect a maximum of 50% or more.Fuel consumption of fishing boats by installing a solar power system is reduced. Also the PV system is useful for the verification of their availability for fishing vessels as well as the satisfaction of the fishermen. The results for the durability of the photovoltaic device is acceptable, including a solar panel, controller and the performance exhibited no breakage in the harsh marine environment or failure so far. The installed PV system was confirmed that the durability with at least 2 years.