PURPOSES : This paper presents a comparison study between dynamic and static analyses of falling weight deflectometer (FWD) testing, which is a test used for evaluating layered material stiffness. METHODS: In this study, a forward model, based on nonlinear subgrade models, was developed via finite element analysis using ABAQUS. The subgrade material coefficients from granular and fine-grained soils were used to represent strong and weak subgrade stiffnesses, respectively. Furthermore, the nonlinearity in the analysis of multi-load FWD deflection measured from intact PCC slab was investigated using the deflection data obtained in this study. This pavement has a 14-inch-thick PCC slab over finegrained soil. RESULTS: From case studies related to the nonlinearity of FWD analysis measured from intact PCC slab, a nonlinear subgrade modelbased comparison study between the static and dynamic analyses of nondestructive FWD tests was shown to be effectively performed; this was achieved by investigating the primary difference in pavement responses between the static and dynamic analyses as based on the nonlinearity of soil model as well as the multi-load FWD deflection. CONCLUSIONS : In conclusion, a comparison between dynamic and static FEM analyses was conducted, as based on the FEM analysis performed on various pavement structures, in order to investigate the significance of the differences in pavement responses between the static and dynamic analyses.

In this study, the fracture property of the bonded structure with aluminum foam is analyzed by using the closed aluminium foam for impact absorber. DCB and TDCB specimens manufactured with the single lap joint method of mode 3 are designed by varying the thickness. The static analysis through ANSYS finite element program is carried out on the specimen model due to each thickness. Also, the static experiment is performed in order to verify the analysis result. This study aims at comparing the shear strengths of the bonded structures of DCB and TDCB made with aluminum foam and investigating the mechanical properties.

As a part of light weight, the adhesive has been applied to joint the mechanical structure. The porous material is used with aluminum foam in case of the structure bonded with only adhesive. In order to confirm the durability, it is necessary to investigate the fracture toughness at the bonded joint. So, the fracture property at joint interface of aluminum foam different from the non-porous material becomes especially important. In this study, the tapered double cantilever beams(TDCB) with the type of mode Ⅲ are manufactured with aluminum foam. The fracture toughness at the joint of the structure bonded with only a adhesive can be obtained. The static analyses are carried out and verified the results by the experiment. As the results of static analyses, the reaction forces ranged from 0.30 to 0.41 kN at all specimens are shown when the forced displacements are proceeded as much as 7 to 9 mm. As the results of analyses and experiments are compared with each other, there is a little bit of difference between these results. Through the result of this study, the mechanical properties at TDCB specimens with the type of mode Ⅲ can be understood.

Because aluminum foam is porous material, the frature property is different from that of non-porous material. This aluminum foam can be used with the joint bonded with adhesive in order to utilize the light weight to the maximum. So, the study of fracture property on bonded surface can be important. In this study, the analyses on the specimens with two kinds of configuration as DCB(Double Cantilever Beams) and TDCB(Tapered Double Cantilever Beams) aluminum foams of mode Ⅲ type bonded with adhesive are carried out and compared with each other. And the fracture properties the adhesive surfaces of the structure with bonded aluminum foams are studied as the static experiments on these verifications are done. DCB and TDCB specimens used in this study have the variable of thickness(t) as 35mm, 45mm and 55mm. As the result of this study, the range of reaction forces are 0.3 to 0.8 kN and 0.5 to 1.2 kN at DCB and TDCB specimens respectively. The results of the static experiments can also be confirmed with these similar results. These study results can be obtained by only a simulation without the special experimental procedures. The mechanical properties of the bonded structures composed of DCB and TDCB aluminum foams with mode Ⅲ type can be thought to be analyzed effectively.

As a part of light weight, the adhesive has been applied to joint the mechanical structure. The porous material is used with aluminum foam in case of the structure bonded with only adhesive. In order to confirm the durability, it is necessary to investigate the fracture toughness at the bonded joint. So, the fracture property at joint interface of aluminum foam different from the non-porous material becomes especially important. In this study, the static facture analysis was carried out with DCB specimen bonded with adhesive as the loading type of mode Ⅲ. The thicknesses of specimens are 35, 45 and 55 mm. When the forced displacements 5 mm applied on the specimen proceed at specimen thicknesses of 35, 45 and 55 mm, the maximum stresses is shown to be happened at the range from 3.3 MPa to 3.6 MPa. The maximum equivalent stress happened at the specimen thickness of 35mm becomes highest among four kinds of specimens. The static experiment is carried on in order to verify these analyses representatively. As the experimental data become similar with the simulation data, it is thought that these analysis data can be applied at analyzing them into the adhesive joint of real porous material.

An aluminum foam is the super light metal which can be adjusted with the adhesive by using the joint method. In this study, the tapered double cantilever beams(TDCB) with the type of mode Ⅲ are manufactured with aluminum foam. The fracture toughness at the joint of the structure bonded with only a adhesive can be obtained. The static analyses are carried out and verified the results by the experiment. As the results of static analyses, the reaction forces ranged from 0.30 to 0.41 kN at all specimens are shown when the forced displacements are proceeded as much as 8 to 9 mm. The tapered double cantilever specimen for mode Ⅲ with the thickness of 55 mm is carried out by the static experiment representatively to verify the analysis results. As the results of analyses and experiments are compared with each other, there is a little bit of difference between these results. So, the simulation results of this study can be thought to be confirmed. It is thought that even the only analysis data omitting the extra experimental procedure can be verified in order to use the data practically. Through the result of this study, the mechanical properties at TDCB specimens with the type of mode Ⅲ can be understood.

As a part of light weight, the adhesive has been applied to joint the mechanical structure. The porous material is used with aluminum foam in case of the structure bonded with only adhesive. In order to confirm the durability, it is necessary to investigate the fracture toughness at the bonded joint. So, the fracture property at joint interface of aluminum foam different from the non-porous material becomes especially important. In this study, the static facture analysis was carried out with DCB specimen bonded with adhesive as the loading type of mode Ⅲ. The thicknesses of specimens are 35, 45 and 55 mm. When the forced displacements 5 mm applied on the specimen proceed at specimen thicknesses of 35, 45 and 55 mm, the maximum stresses is shown to be happened at the range from 3.3 MPa to 3.6 MPa. The maximum equivalent stress happened at the specimen thickness of 35mm becomes highest among four kinds of specimens. The static experiment is carried on in order to verify these analyses representatively. As the experimental data become similar with the simulation data, it is thought that these analysis data can be applied at analyzing them into the adhesive joint of real porous material.

본 연구는 복합재료 교량시스템의 규준 정립을 위한 연구로서 실제 설계 시공되어진 복합재료 교량의 정밀해석수행과 이를 통한 복합재료 교량의 파괴거동 및 설계기준 등을 조사하는데 그 목적이 있다. 본 연구의 효율적인 연구를 위하여 실제 미국 NEW YORK주 내에 설계 시공되어있는 Noncomposite-FRP 복합재료 교량을 대상으로 해석적 연구를 수행하였으며 본 연구에서 사용된 해석적 모델을 토대로 실제 미국에서 기 수행되어진 교량 거동에 관한 해석 및 실험하중 평가와 그 결과를 비교하였다. 특히 국내 복합재료 교량의 해석적 설계기준 평가를 위하여 보다 실질적이고 정확한 파괴모드의 조사 및 분석이 요구되어지므로 본 연구에서는 이를 위하여 기존의 해석적 연구에서 가벼운 중량으로 인하여 무시되었던 자중의 영향과 각 적층 layer에 설계된 ply orientation을 고려하여 해석하였다. 그 결과 자중을 고려한 복합재료 패널들의 경우, 제작 결함에 따른 이음부 파괴가 없을 경우 교량 상부 구조 중 횡축 보에서의 국부 좌굴 파괴가 교량의 파괴를 지배할 것으로 본 연구결과에서 예측되었다. 이는 복합재료 교량 제작 시 복합재료 상판 패널과 보의 이음부가 Noncomposite로 제작되는 경우 실제 제작되어진 복합재료 상판의 고 강성에 의하여 재하 하중에 의한 하부 강재 거더 좌굴이 선행되는 것으로 판단된다.

SiCp/6061AI 복합재료의 파괴인성을 평가하기 위하여 정적파괴인성에 대해서는 복수시험편법을, 동적파괴인성시험에 대해서는 stop block법을 실시하였다. 주균열은 예비균열의 선단에서 시험편두께방향 전역에 걸쳐서 일시에 발생하는 것이 아니고, 균열발생의 초기단계에서 국부적으로 형성된 균열이 시험편두께방향으로의 균열의 확장을 완료한 후 주균열로 이행해 간다. 정적 및 동적시험에서 컴플라이언스변화율법에 의해 검출된 균열발생점은 균열확장의 완료점과 거의 일치하고 있기 때문에 본 재료의 파괴인성 결정에 유효하다. 본 재료에서 동적파괴인성치는 정적파괴인성치보다 크게 나타났다. 이것은 동적충격시 입자파괴에 의한 에너지의 흡수.분산효과와 균열진전경로의 큰 편향에 기인한다고 생각된다.

횡방향으로 프리스트레스가 도입된 장지간 PSC 바닥판의 정적 거동을 예측하기 위한 유한요소해석 모델을 구성하고, 해석결과를 선행연구에 의한 실험결과와 비교하였다. 유한요소해석에 의하여 서로 다른 콘크리트 강도와 프리스트레스 크기를 변수로 갖는 각각의 실험체에 대한 하중-처짐 관계 곡선을 비교적 근접하게 추정할 수 있었다. 또한, 변형률 분포와 변수에 따른 극한강도 변화로부터 펀칭전단에 의한 파괴형태와 손상범위 등을 간접적으로 예측할 수 있었다. 이 연구에서 활용된 유한요소해석 모델은 펀칭전단파괴에 의한 펀칭콘의 분리를 사실적으로 재현하기 위한 목적이 아니며, 실험연구를 위한 보조적 수단으로서 정적거동예측과 실험결과의 보완 등에 효과적으로 활용될 수 있을 것으로 판단된다.