One of the key challenges for the commercialization of carbon nanotube fibers (CNTFs) is their large-scale economic production. Among CNTF spinning methods, surfactant-based wet spinning is one of the promising techniques for mass producing CNTFs. Here, we investigated how the coagulation bath composition affects the spinnability and the properties of CNTFs in surfactant-based wet spinning. We used acetone, DMAc, ethanol, and IPA as coagulants and analyzed the relationship between coagulation bath composition and the properties of CNTFs in terms of kinetic and thermodynamic coagulation parameters. From a kinetic perspective, we found that a low mass transfer rate difference (MTRD) is favorable for wet spinning. Based on this finding, we mixed the coagulant bath with solvent in a proper ratio to reduce the MTRD, which generally improved the wet spinning. We also showed that the coagulation strength, a thermodynamic parameter, should be considered. We believe that our research can contribute to establishment of surfactant-based wet spinning of CNTFs.

This paper explores the potential application of carbon nanotubes (CNTs) in the construction industry, as CNTs can effectively serve as nano-fillers, bridging the voids and holes in cement structures. However, the limited dispersibility of CNTs in water necessitates the use of dispersing agents for achieving uniform dispersion. In this study, two kinds of cement superplasticizers, polycarboxylate ether (PCE) and sulfonated naphthalene formaldehyde (SNF) were employed as dispersing agents to improve the interfacial affinity between CNTs and cement, and to enhance the strength of the cement nanocomposites. Contact angle experiments revealed that the utilization of PCE and SNF effectively addressed the interface issues between CNTs and cement. As a result, the cement nanocomposite with a CNT to PCE ratio of 1:2 exhibited an approximately 6.6% increase in compressive strength (73.05 MPa), while the CNT:SNF 1:2 cement composite showed a 4.7% increase (71.72 MPa) compared to plain cement (68.52 MPa). In addition, the rate of crack generation in cement nanocomposites with CNTs and dispersing agents was found to be slower than that of plain cement. The resulting cement nanocomposites, characterized by enhanced strength and durability, can be utilized as safer materials in the construction industry.

The interface area of the face sheet and core of the sandwich composite is seen as a weakness due to its low de-bonding toughness. To overcome this concern, it is critical to develop a suitable modification strategy to enhance the de-bonding toughness of the face sheet/core interface. In the present study, the corrugated core reinforced sandwich composite was prepared through co-curing and secondary bonding approaches. The MWCNTs reinforced adhesive was induced in the face sheet/core interface in different weight concentrations. The MWCNT-reinforced adhesive was prepared using the sonication technique, and its dispersion was examined using atomic force microscopy (AFM). The three-point bending test revealed that sandwich composite prepared using the co-cure method has higher flexural strength than secondary bonded samples due to better bonding face sheet and corrugated core. Compared with MWCNT-free corrugated core reinforced co-cured sandwich composites (CCSC), the flexural strength of 1 wt.% MWWCNT-induced sandwich composite was increased by 101.28%. The microstructural study showed that secondary bonded samples had extensive fibre breakage at the face plate due to early de-bonding of the face sheet and corrugated core. Furthermore, the free vibrational analysis was performed to evaluate the natural frequency and damping values of the corrugated core reinforced sandwich composite. The modal test results indicated that inducing 1wt.% MWCNTs in the face sheet/core interface had enhanced the natural frequencies of co-cured sandwich composites. The present study provides a suitable method to address the weaker de-bonding toughness concerns of face sheet/core interface region of sandwich structures.

Single-walled carbon nanotubes (SWNT) have a strong and stable near-infrared (nIR) fluorescence that can be used to selectively detect target analytes, even at the single molecule level, through changes in either their fluorescence intensity or emission peak wavelength. SWNTs have been employed as NIR optical sensors for detecting a variety of analytes. However, high costs, long fabrication times, and poor distributions limit the current methods for immobilizing SWNT sensors on solid substrates. Recently, our group reported a protocol for SWNT immobilization with high fluorescence yield, longevity, fluorescence distribution, and sensor response, unfortunately this process takes 5 days to complete. Herein we report an improved method to immobilize SWNT sensors that only takes 2 days and results in higher fluorescence intensity while maintaining a high level of SWNT distribution. We performed surface morphology and chemical composition tests on the original and new synthesis methods and compared the sensor response rates. The development of this new method of attaching SWNT sensors to a platform allows for creation of a sensing system in just 2 days without sacrificing the advantageous characteristics of the original, 5-day platforms.

This research introduces an innovative approach for evaluating the degree of densification of carbon nanotube (CNT) sheets produced through direct spinning and subsequently treated with organic solvent (specifically ethanol). Analysis of the morphological features of the CNT sheets from the FE-SEM image affirms that the sheet’s structure becomes more densified following the treatment. Based on this, the treated CNT sheet was comprehensively evaluated using Raman spectroscopy. The results indicate a downward shift in the G′ band, signifying the densification of the CNT sheet’s structure due to the C–C bond weakening by the cohesive force. Following ethanol treatment, the CNT sheet exhibited enhanced electrical conductivity and tensile strength, measuring approximately 1.7 × 105 S m− 1 and 138.7 MPa, respectively, a remarkable improvement of roughly 300% compared to the untreated CNT sheet. This study underscores the efficacy of Raman spectroscopy as a powerful tool for assessing the densification of CNT sheets.

본 연구에서는 탄소나노튜브(CNT) 패치 센서를 기반으로 하여 구조물의 이상 거동을 감지하고 대 응할 수 있도록 하는 첨단 스마트 모니터링 시스템을 제안한다. 복합소재로 제작되는 CNT 센서는 유 연한 특성을 갖게 되어 다양한 형태의 구조물 표면에 적용할 수 있으며, 이를 통해 충격이나 피로 등 에 의해 발생되는 균열과 같은 비정상적인 거동을 감지할 수 있다. CNT 센서를 통해 수집한 데이터 는 IoT 시스템을 통해 실시간으로 분석되어 구조물의 거동 상태를 확인하고 건전성을 모니터링 할 수 있게 한다. 이 시스템의 성능 검증 및 사용성 검토를 위해 미국 소재 교량에서 실증 테스트를 하였으 며, 테스트 결과 CNT 센서를 이용한 구조물 거동 감지 시스템을 통해 구조물의 이상 거동을 효과적 으로 감지하고 모니터링하여 구조물에서 발생 될 수 있는 잠재적 문제를 사전에 예방할 수 있음을 확 인하였다. 이와 같은 기술은 추후 다양한 분야에서 적극적으로 활용될 수 있을 것으로 기대된다.

다양한 원인으로 콘크리트 구조물에 하중이 작용되며, 이에 대한 적절한 대응이 이루어지지 않으면 구조물에 열화가 발생하고, 붕괴와 같은 대규모 재난을 초래할 수 있다. 구조물에 발생하는 하중을 감 지하는 연구는 지속적으로 이루어지고 있지만, 안전성 모니터링을 위한 혁신적인 시스템에는 여전히 부족함이 존재한다. 탄소나노튜브/폴리우레탄 복합체는 다양한 공학 분야에서 구조물 건전성 모니터링 을 위한 센서로 활용되어 센싱 효과가 뛰어난 것으로 알려져 있다. 따라서 본 연구에서는 다양한 공학 분야에서 구조물 건전성 모니터링 센서로 활용되고 있는 탄소나노튜브/폴리우레탄 복합체를 제작하여 모니터링 시스템을 개발하였다. 다양한 하중에 대한 센싱 성능을 파악하기 위해 인장, 압축, 충격 시험 을 진행하였고, 동시에 센서의 전기적 변화를 분석하였다. 추가적으로 본 센서가 구조물 표면에 적용 됨에 따라 온도, 습도와 같은 환경적 영향성을 분석하여 활용 가능성을 평가하였다. 또한, 최대 48행, 48열의 다중 계측이 가능한 IoT 기반 다중 모니터링 시스템을 개발하고, 이를 구조물에 적용된 센서 와 연계하여 스마트 모니터링 시스템으로서의 성능을 평가하였다. 이를 통해 탄소나노튜브/폴리우레탄 복합체 기반 센서는 구조물 하중 감지 시스템으로 활용이 가능할 것으로 판단되었다.

This paper presents an electrochemical immunosensor using a graphene/multi-walled carbon nanotube (MWCNT) composite platform for detecting the cardiovascular marker C-reactive protein (CRP). The immunosensor exhibited a linear detection range of 0.20–100 ng/mL CRP with a low limit of detection reaching 0.081 ng/mL. The composite material provided a 3D porous structure that allowed efficient antibody immobilization and minimized steric hindrance. The sensor showed high specificity, with minimal response to interfering substances. Using differential pulse voltammetry, the immunosensor demonstrated exceptional precision, rapid detection, and a direct correlation between CRP concentration and sensor response current. Overall, this work highlights the potential of the graphene/MWCNT composite platform as a robust tool for early CRP detection and cardiovascular disease risk assessment. The immunosensor provides sensitive and selective CRP quantification that could enable timely clinical intervention for at-risk individuals.

In order to prevent early distress in asphalt pavement and save on subsequent operational and maintenance costs, modifying asphalt is an effective approach. Styrene–butadiene–styrene (SBS) block copolymers, due to their excellent physicochemical properties, have become a mature and widely used asphalt modifier. Carbon nanotubes (CNTs) possess advantages such as a large specific surface area and high modulus, which, when incorporated into asphalt, can enhance its deformation resistance. To analyze the effect of incorporating CNTs on SBS-modified asphalt (SBS-A), this study analyzed the influence of different CNT concentrations on the high and low-temperature performance and aging properties of SBS-A through penetration, softening point, ductility, dynamic shear rheometry, and short-term aging tests. The optimal CNT concentration was determined to be 1.0%. Furthermore, the changes in the modified asphalt during the aging process were analyzed using infrared spectroscopy.

Metals are recognized as electromagnetic interference (EMI) shielding materials owing to their high electrical conductivity. However, the need for light and flexible EMI shielding materials has emerged, owing to the heavyweight and inflexible nature of metals. Carbon nanotube (CNT)/polymer composites have been studied as promising flexible EMI shielding materials because of their lightweight nature due to the low density of CNTs and their high electrical conductivity. CNTs evenly dispersed in the polymer form an electrically conductive network, and the aspect ratio of the CNTs, which are one-dimensional nanofillers, is an important factor affecting electrical conductivity. In this study, we prepared three types of multi-walled carbon nanotubes (MWNTs) with different aspect ratios and fabricated polydimethylsiloxane (PDMS)/MWNT composites. Subsequently, the electrical conductivities and electrical percolation thresholds of the three PDMS/MWNT composites with different MWNT aspect ratios were measured to analyze the behavior of electrically conducting network formation according to the aspect ratio. Furthermore, the total EMI shielding effectiveness of each composite was determined to evaluate the effect of the MWNT aspect ratio on the EMI shielding. Reflection and absorption of electromagnetic wave were measured for the PDMS/MWNT composite with the largest aspect ratio to analyze the EMI shielding mechanism of the composite. Additionally, the effects of the MWNT content on the conductivity and EMI shielding performance were examined. The results provide valuable guidance for designing polymer MWNT composites with good electrical conductivity and EMI shielding performance under different aspect ratios of MWNTs.

Aqueous Zn-ion batteries (ZIBs) are very attractive owing to their high safety and low cost. Among various cathode materials, organic materials-based electrodes incorporating various redox functional groups have gained significant attention in the field of ZIBs due to their benefits of a tunable structural design, facility, eco-friendly, and possibility of multivalent energy storage. Herein, we demonstrate the nanostructured organic active materials deposited onto the CNT networks (HyPT@ CNT) for flexible ZIBs. This HyPT nanorods were obtained reassemblying the herringbone structured 3,4,9,10-tetracarboxylic dianhydride through a hydrothermal process in the presence of acid. These HyPT@CNT hybrids were electronically conductive and redox active, as well as could be fabricated into a flexible electrode achieving flexibility from mechanical integrity of robust networked structure. The as-fabricated flexible ZIBs delivered the high capacity of 100 Ah g− 1 at a current density of 0.1 A g− 1 and long-term cycling performance exceeding 5000 cycles. Consequently, these electrochemical performances are associated with the redox reactivity of carbonyl groups as verified by spectroscopic and electrochemical characterizations and the hybridization of HyPT nanorods with CNT networks.

The conventional multi-scale modelling approach that predicts carbon nanotube (CNT) growth region in heterogeneous flame environment is computationally exhaustive. Thus, the present study is the first attempt to develop a zero-dimensional model based on existing multi-scale model where mixture fraction z and the stoichiometric mixture fraction zst are employed to correlate burner operating conditions and CNT growth region for diffusion flames. Baseline flame models for inverse and normal diffusion flames are first established with satisfactory validation of the flame temperature and growth region prediction at various operating conditions. Prior to developing the correlation, investigation on the effects of zst on CNT growth region is carried out for 17 flame conditions with zst of 0.05 to 0.31. The developed correlation indicates linear ( zlb=1.54zst +0.11) and quadratic ( zhb=zst(7-13zst )) models for the zlb and zhb corresponding to the low and high boundaries of mixture fraction, respectively, where both parameters dictate the range of CNT growth rate (GR) in the mixture fraction space. Based on the developed correlations, the CNT growth in mixture fraction space is optimum in the flame with medium-range zst conditions between 0.15 and 0.25. The stronger relationship between growth-region mixture-fraction (GRMF) and zst at the near field region close to the flame sheet compared to that of the far field region away from the flame sheet is due to the higher temperature gradient at the former region compared to that of the latter region. The developed models also reveal three distinct regions that are early expansion, optimum, and reduction of GRMF at varying zst.

Small-film-type ion sensors are garnering considerable interest in the fields of wearable healthcare and home-based monitoring systems. The performance of these sensors primarily relies on electrode capacitance, often employing nanocomposite materials composed of nano- and sub-micrometer particles. Traditional techniques for enhancing capacitance involve the creation of nanoparticles on film electrodes, which require cost-intensive and complex chemical synthesis processes, followed by additional coating optimization. In this study, we introduce a simple one-step electrochemical method for fabricating gold nanoparticles on a carbon nanotube (Au NP–CNT) electrode surface through cyclic voltammetry deposition. Furthermore, we assess the improvement in capacitance by distinguishing between the electrical double-layer capacitance and diffusion-controlled capacitance, thereby clarifying the principles underpinning the material design. The Au NP–CNT electrode maintains its stability and sensitivity for up to 50 d, signifying its potential for advanced ion sensing. Additionally, integration with a mobile wireless data system highlights the versatility of the sensor for health applications.

Nowadays, variable materials have been investigated to find alternative lightweight conductors instead of copper because copper has a relatively high density. Carbon nanotube (CNT) is one of the most suitable materials as an alternative conductor to Cu, thanks to its high conductivity. In addition, CNT has many other great properties, such as low density, high strength, and high ampacity. However, individual CNT loses some of its performance after the assembly process. Therefore, CNT materials have been electroplated with copper to achieve lighter conductors. In this study, CNT buckypaper (CNTBP) is fabricated using a multi-walled carbon nanotube and copper electroplated using optimizing electrolyte with the help of additive chemicals such as accelerator and suppressor. Furthermore, the effect of hydrochloric acid in the electrolyte on the electroplating of CNTBP is observed. The results show that HCl in electrolyte enhances the effectiveness of additive chemicals and provide a well-plated CNTBP@Cu composite. The composite in this study is expected to be used in various areas.

Carbon nanotube fiber is a promising material in electrical and electronic applications, such as, wires, cables, batteries, and supercapacitors. But the problem of joining carbon nanotube fiber is a main obstacle for its practical development. Since the traditional joining methods are unsuitable because of low efficiency or damage to the fiber structure, new methods are urgently required. In this study, the joining between carbon nanotube fiber was realized by deposited nickel–copper doublelayer metal via a meniscus-confined localized electrochemical deposition process. The microstructures of the double-layer metal joints under different deposition voltages were observed and studied. It turned out that a complete and defect-free joint could be fabricated under a suitable voltage of 5.25 V. The images of the joint cross section and interface between deposited metal and fiber indicated that the fiber structure remained unaffected by the deposited metal, and the introduction of nickel improved interface bonding of double-layer metal joint with fiber than copper joint. The electrical and mechanical properties of the joined fibers under different deposition voltages were studied. The results show that the introduction of nickel significantly improved the electrical and mechanical properties of the joined fiber. Under a suitable deposition voltage, the resistance of the joined fiber was 37.7% of the original fiber, and the bearing capacity of the joined fiber was no less than the original fiber. Under optimized condition, the fracture mode of the joined fibers was plastic fiber fracture.