본 연구는 2017년부터 2021년까지 고속도로에서 발생한 약 9,600건의 사고를 분석하여 자율주행 긴급차량의 신속한 대응 능력을 향 상시키고자 하였다. 조사 결과, 2차 사고가 전체 사망자의 16.8%를 차지하며, 이들 중 약 74%가 선행사고와 관련이 있다는 점이 강조 된다. 이러한 통계는 긴급차량의 신속한 대처 능력이 피해를 최소화하는 데 얼마나 중요한지를 보여준다. 연구에서는 사고의 영향권을 정의하고, 이를 기반으로 긴급차량이 보다 안전하고 효율적으로 사고 현장에 접근할 수 있도록 하는 알고리즘을 개발하였다. 실제 교 통사고 데이터를 활용하여 사고 지속 시간과 다양한 변수를 고려한 기초 분석을 실시하였으며, 도로 특성, 사고 종류, 점유 차로 등 여러 요소를 반영하여 대응 기준을 설정했다. 알고리즘은 자율주행 차량이 실시간으로 주변 정보를 수집하고 신속하게 대응 방안을 마련할 수 있도록 설계되었다. 향후 연구에서는 알고리즘의 실제 도로 환경에서의 적용 가능성을 검토하고, 다양한 변수들을 포함한 추가 연구를 통해 성능을 더욱 개선할 계획이다. 이러한 연구 결과는 교통사고로 인한 피해를 줄이는 데 기여하고, 자율주행 기술을 활용하여 2차 사고의 가능성을 감소시키는 데 중요한 역할을 할 것으로 기대된다.

PURPOSES : This study analyzes the accident damage scale of hazardous material transportation vehicles not monitored in real time by the Hazardous Material Transportation Safety (HMTS) management center. METHODS : To simulate hazardous-material transportation vehicle accidents, a preliminary analysis of transportation vehicle registration status was conducted. Simulation analyses were conducted for hazardous substance and flammable gas transportation vehicles with a high proportion of small- and medium-sized vehicles. To perform a spill accident damage-scale simulation of hazardous-substance transportation vehicles, the fluid analysis software ANSYS Fluent was used. Additionally, to analyze explosion accidents in combustible gas transportation vehicles, the risk assessment software Phast and Aloha were utilized. RESULT : Simulation analysis of hazardous material transportation vehicles revealed varying damage scales based on vehicle capacity. Simulation analysis of spillage accidents showed that the first arrival time at the side gutter was similar for various vehicle capacities. However, the results of the cumulative pollution analysis based on vehicle capacity exhibited some differences. In addition, the simulation analysis of the explosion overpressure and radiant heat intensity of the combustible gas transportation vehicle showed that the difference in the danger radius owing to the difference in vehicle capacity was insignificant. CONCLUSIONS : The simulation analysis of hazardous-material transportation vehicles indicated that accidents involving small- and medium-sized transportation vehicles could result in substantial damage to humans and ecosystems. For safety management of these small and medium-sized hazardous material transportation vehicles, it is expected that damage can be minimized with the help of rapid accident response through real-time vehicle control operated by the existing HMTS management center.

PURPOSES : This study is to initiated to estimate the impact of mixed traffic flow on expressway section according to the market penetration rate(MPR) of automated vehicles(AVs) using a enhanced intelligent driver model(EIDM). METHODS : To this end, microscopic traffic simulation and EIDM were used to implement mixed traffic flow on basic expressway section and simulation network was calibrated to understand the change of impact in mixed traffic flow due to the MPR of AVs. Additionally, MOEs of mobility aspects such as average speed and travel time were extracted and analyzed. RESULTS : The result of the impact of mobility MOEs by MPR and level of service indicated that 100% MPR of AVs normally affect positive impact on expressway at all level of service. However, it was analyzed that improvements in the level of service from LOS A to C are minimal until the MPR of AVs reaches 75% or higher. CONCLUSIONS : This research shows that impact of MPR of AVs using EIDM of mixed traffic flow on basic expressway. Increasing MPR of AVs affects positive impact on expressway at all level of services. However, MPR from 25% to 75% of AVs in LOS A to C shows minimal impacts. Therefore, to maximize the effectiveness of AVs, appropriate traffic operation and management strategies are necessary.

One of the indicators evaluate the bridge load bearing capacity is the peak impact factor. The peak impact factor is related to vehicle types and speeds and frequency of the bridges. Among the parameters, the vehicle types such as DB-24 and standard vehicle load presented in the current specification have different load distribution and different load axles space. Considering these features, in the present study, the variation of the peak impact factor according to each vehicle type is investigated and compared.