This study focuses on the development of coatings designed for storage containers used in the management of radioactive waste. The primary objective is to enhance the shielding performance of these containers against either gamma or neutron radiation. Shielding against these types of radiation is essential to ensure the safety of personnel and the environment. In this study, tungsten and boron cabide coating specimens were manufactured using the HVOF (High-Velocity Oxy Fuel) technuqe. These coatings act as an additional layer of protection for the storage containers, effectively absorbing and attenuating gamma and neutron radiation. The fabricated tungsten and boron carbide coating specimens were evaluated using two different testing methods. The first experiment evaluates the effectiveness of a radiation shielding coating on cold-rolled steel surfaces, achieved by applying a mixture of WC (Tungsten Carbide) powders. WC-based coating specimens, featuring different ratios, were prepared and preliminarily assessed for their radiation shielding capabilities. In the gamma-ray shielding test, Cs-137 was utilized as the radiation source. The coating thickness remained constant at 250 μm. Based on the test results, the attenuation ratio and shielding rate for each coated specimen were calculated. It was observed that the gammaray shielding rate exhibited relatively higher shielding performance as the WC content increased. This observation aligns with our findings from the gamma-ray shielding test and underscores the potential benefits of increasing the tungsten content in the coating. In the second experiment, a neutron shielding material was created by applying a 100 μm-thick layer of B4C (Boron Carbide) onto 316SS. The thermal neutron (AmBe) shielding test results demonstrated an approximate shielding rate of 27%. The thermal neutron shielding rate was confirmed to exceed 99.9% in the 1.5 cm thick SiC+B4C bulk plate. This indicates a significant reduction in required volume. This study establishes that these coatings enhance the gamma-ray and neutron shielding effectiveness of storage containers designed for managing radioactive waste. In the future, we plan to conduct a comparative evaluation of the radiation shielding properties to optimize the coating conditions and ensure optimal shielding effectiveness.

The amount of waste that contains or is contaminated with radionuclides is increasing gradually due to the use of radioactive material in various fields including the operation and decommissioning of nuclear facilities. Such radioactive waste should be safely managed until its disposal to protect public health and the environment. Predisposal management of radioactive waste covers all the steps in the management of radioactive waste from its generation up to disposal, including processing (pretreatment, treatment, and conditioning), storage, and transport. There could be a lot of strategies for the predisposal management of radioactive waste. In order to comply with safety requirements including Waste Acceptance Criteria (WAC) at the radioactive waste repository however, the optimal scenario must be derived. The type and form of waste, the radiation dose of workers and the public, the technical options, and the costs would be taken into account to determine the optimal one. The time required for each process affects the radiation dose and respective cost as well as those for the following procedures. In particular, the time of storing radioactive waste would have the highest impact because of the longest period which decreases the concentrations of radionuclides but increases the cost. There have been little studies reported on optimization reflecting variations of radiation dose and cost in predisposal management scenarios for radioactive waste. In this study, the optimal storage time of radioactive waste was estimated for several scenarios. In terms of the radiation dose, the cumulative collective dose was used as the parameter for each process. The cost was calculated considering the inflation rate and interest rate. Since the radiation dose and the cost should be interconvertible for optimization, the collective dose was converted into monetary value using the value so-called “alpha value” or “monetary value of Person-Sv”.

Operating and decommissioning nuclear power plants generates radioactive waste. This radioactive waste can be categorized into several different levels, for example, low, intermediate, and high, according to the regulations. Currently, low and intermediate-level waste are stored in conventional 200-liter drums to be disposed. However, in Korea, the disposal of intermediate-level radioactive waste is virtually impossible as there are no available facilities. Furthermore, large-sized intermediate- level radioactive waste, such as reactor internals from decommissioning, need to be segmented into smaller sizes so they can be adequately stored in the conventional drums. This segmentation process requires additional costs and also produces secondary waste. Therefore, this paper suggests repurposing the no-longer-used spent nuclear fuel casks. The casks are larger in size than the conventional drums, thus requiring less segmentation of waste. Furthermore, the safety requirements of the spent nuclear fuel casks are severer than those of the drums. Hence, repurposed spent nuclear fuel casks could better address potential risks such as dropping, submerging, or a fire. In addition, the spent nuclear fuel casks need to be disposed in compliance with the regulations for low level radioactive waste. This cost may be avoided by repurposing the casks.

The mechanical safety of the container designed according to the IP-2 type technology standard was analyzed for the temporary storage and transportation of Very-Low-Level-Waste (VLLW) for liquid occurring at the nuclear facilities decommissioning site. The container was designed and manufactured as a composite shielding container with the effect of storing and shielding liquid radioactive waste using High Density Polyethylene (HDPE) and eco-friendly shielding material (BaSO4) with corrosion and chemical resistance. The main material of the composite shielding container is HDPE and BaSO4, the material of the cover, cage and pallet is SUS304, and the angle guard is elastic rubber. The test and analysis requirements were analyzed for structural analysis of container drop and lamination test. As test requirements for IP-2 type transport containers should be verified by performing drop and lamination tests. There should be no loss or dispersion of contents through the 1.2 m high free-fall drop and lamination test for a load five times the amount of transported material. ABAQUS/Explicit, a commercial finite element analysis program, was used for structural analysis of the drop and lamination test of the transport and storage container. (Drop test) It was confirmed that the container was most affected when it falls from a 45-degree slope. Although plastic deformation was observed at the edge axis of the cover, it was evaluated that the range of plastic deformation was limited to the cover and cage, and stress within the elastic limit occurred in the inner container. In the analysis results for other falling direction conditions, it was evaluated that stress within the elastic limit was generated in the inner container except for minor plastic deformation. In the case of on-site simulation evaluation, deformation of the inner container and frame due to the drop impact occurred, but leakage and loss of contents, which are major evaluation indicators, did not occur. (Lamination test) The maximum stress was calculated to be 19.9 MPa under the lamination condition for a load 5 times the container weight, and the maximum stress point appeared at the corner axis of the pallet. The calculated value for the maximum stress is about 10%, assuming the conservative yield strength of SUS304 is 200 MPa. It was evaluated that stress within the limit occurred. In the case of on-site simulation evaluation, it was confirmed that there was no container deformation or loss of contents due to the load.

The structural safety of prototype transport and storage containers for very low-level radioactive liquid waste was experimentally estimated for its localization development. Transport containers for radioactive liquid waste have been researched and developed, however, there are no standardized commercial containers for very low-level radioactive waste in Korea. In this study, the structural safety of the designated IP-2 type container capable of transporting and temporarily storing large amounts of very low-level liquid waste, which is generated during the operation and decommissioning of nuclear power plants, was demonstrated. The stacking and drop tests, which were conducted to determine the structural integrity of the container, verified that there was no external leakage of the contents in spite of its structural deformation due to the drop impact. This study shows the effort required for the localization of the technology used in manufacturing transport and storage containers for very low-level radioactive liquid waste, and the additional structural reinforcement of the container in which the commercial intermediate bulk container (IBC) external frame was coupled.