Neptunium (Np) is one of the daughter elements included in the decay chain of Pu. The quantitative analysis of Np isotopes is required for radioactive waste characterization, research on actinide chemistry, etc. Np-237 has a long half-life (2.144 million years), but its daughter Pa-233 has a relatively short half-life (26.975 days). For this reason, after a sufficient time elapses following the chemical preparation process of the analyte, the two nuclides are in radiation equilibrium in the sample. Np-237 emits alpha-rays while Pa-233 emits beta-rays. Both nuclides also emit gamma- and X-rays. In this study, alpha-rays were measured using liquid scintillation counting (LSC) method and alpha spectrometry. Gamma-spectrometry with a HPGe detector was used for the analysis of gammaand X-rays. In addition, we compared the radiometric results with quantitative analysis of Np using UV-Vis absorption spectrometry. The LSC method and the HPGe gamma-spectroscopy do not require extensive sample preparation procedures. Alpha spectroscopy requires a standard material spiking, separation by coprecipitation, and disk-type sample preparation procedure to obtain measurement efficiency and recovery factor. A reference material sample with a concentration of 5.8 mM was analyzed by the four analysis methods, and all of the measured results agreed well within a difference level of 4%.

We established pretreatment method of solidified cement ion-exchange resin samples generated before 2003 in nuclear power plants for measurement of non-volatile radionuclide activity. A microwave digestion system (MDS) with mixed acid (HCl-HNO3-HF-H2O2) was used to dissolve cement and to desorb non-volatile elements such as Ce, Co, Cs, Fe, Nb, Ni, Re, Sr and U from mixed ion-exchange resin. The content of Ce, Co, Fe, Nb, Ni, Re, Sr, U and Cs after pretreatment of cement plus mixed ion-exchange resin was measured by ICP-AES and ICP-MS, respectively. As iron and strontium are also present in cement, their content after dissolving a certain amount of cement was measured by ICP-AES. All elements except Nb were quantitatively recovered. Especially since the Nb recovery was low at 72.0±2.5%, the MDS following addition of the mixed acid to the resin was operated once more for desorbing Nb from it. Finally the recovery of Nb was over 95%. This sample pretreatment method will be applied to solidified cement ion-exchange resin samples generated in nuclear power plants for assessment of radionuclide inventory.

The massive amount of radioactive waste will generated during decommissioning of nuclear. Among the radioactive waste from these disposal process, 50-55 million tons of concrete waste are included. For safe disposal, it is very important to accurately analyze the concentration of radionuclides, especially 129I and 131I, contaminated concrete. 129I, a long-lived radioisotope of iodine (t1/2=1.57 × 107 y), and 131I (t1/2=8.04 d) are generated from the fission of uranium in nuclear reactors. In Korea, according to the Nuclear Safety and Security Commission (NSSC) radioactive clearance level guide, the limit for radioactive clearance level of 129I is less than 0.01 (Bq/g). Iodine can be absorbed, accumulate in organisms, and exhibit low energy emission compared with cesium, and cobalt. Therefore, it is essential to an accurately separate and analyze iodine radioactive waste. In this study, we focused on the determination of iodine in simulated cement waste form containing KI for the recovery of iodine. We performed cement waste form sieved through a different particle size (0.5 mm < ɸ < 6.35 mm). For the separation of iodine from solid samples with low iodine content, such as soil, sediment, and cement, for sample decomposition associated with solvent extraction using CHCl3 for separation of iodine from the matrix. The separation of iodine in cement waste particles was therefore carried out using an acid leaching method using KI containing cement particles. We observed that cement particle size decreased at 6.35 mm to 0.5 mm with iodine yield decrease at 0.840±0.011 to 0.582±0.010. Thus, in this study, the acid leaching method enables to determination Iodine in cement.

Attempts to use the molten salt system in various aspects such as MSR or energy storage systems are increasing. However, there are limitations in the molten salt-assisted technique due to the harsh corrosiveness of the molten salt, and a more detailed study on salt-induced corrosion is needed to solve this problem. In this study, corrosion behaviors of 80Ni-20Cr alloy in various salt environments such as eutectic NaCl-MgCl2 with NiCl2, CrCl2, and EuCl3 additives were investigated. Meanwhile, the corrosion acceleration effects of 80Ni-20Cr specimens were analyzed for various ceramic materials such as SiC, Al2O3, SiO2, graphite, and BN, and metallic materials such as Ni-based alloy, Fe-based alloy, and pure metals in a molten salt environment. The experiments were conducted at 973 K for up to 28 days, and after the experiment, the microstructural change of the specimen was analyzed through SEM-EDS, and salt condition was analyzed by ICP-OES.

In this study, molten salt experiments were performed using a multi-purpose molten salt experimental loop to evaluate the corrosion and thermodynamic properties of the molten salt. The multi-purpose molten salt experimental loop is made of 1-inch austenitic 316 stainless steel, and 1/4-inch austenitic 316 stainless steel tubes were welded on the surface of a 1-inch pipe to measure temperatures of molten salt. During the experiment, the molten salt leaked due to corrosion of the welded part of the 1/4-inch tube connected to the 1-inch pipe. Therefore, the cause of corrosion damage of the leaked welded part was analyzed. The effect of NaCl-MgCl2 salt selected as the molten salt on corrosion failure was considered. And based on the operation data of molten salt experiments, the time of occurrence of the issue was estimated. Lastly, the cause of corrosion failure was estimated by comparing and analyzing the pipe shape before and after failure using SEM-EDS.

Combustion method has been widely used in the analysis of 3H and 14C in various types of radioactive wastes since X. Hou reported the analysis of 3H and 14C in graphite and concrete for decommissioning of nuclear reactor. In this work, it was demonstrated that the validation result of combustion method for the simultaneous analysis of 3H and 14C in non-combustible radioactive wastes. To validate the combustion method, 3H and 14C spiked to sea sand and soil were prepared and each simulated sample was combusted with the accordance to a combustion temperature program. The validation of combustion method was assessed by the radioactivity recovery, radioactivity deviation, and relative standard deviation of measured radioactivity. The results of radioactivity recovery, radioactivity deviation, and relative standard deviation of 14C were 100~105%, less than 7%, less than 5%, respectively. In addition, 3H showed about 90% of radioactivity recovery, less than 20% of radioactivity deviation, and less than 5% of relative standard deviation. It will be provided that the validation results of combustion method in detail.

Concrete waste generated in the result of dismantling a concrete structure in a radiation control area and refractory brick waste generated from uranium pellet sintering furnace are surface-contaminated by uranium particle of which the enrichment is below 5%. These wastes are hard to decontaminate so it was necessary to develop the process for its disposal. So, we developed the Process Control Plan (PCP) for disposal of radioactive concrete waste describing a whole sequence of disposal and inspecting procedures based on the KNF Radioactive Waste Quality Assurance Plan (KN-WQAP) established in 2021. Based on the PCP, we crushed the concrete waste by jaw-crusher. Then we sieved the crushed concrete waste and removed the particle of which size is below 0.3 mm, using sieve-vibrator where the 0.3 mm mesh-sized sieve is installed inside. Before conducting the crush-sieving method based on the PCP, we conducted Process Control Assessment (PCA) based on the KN-WQAP. The purpose of the PCA is to check whether the output of the process satisfies the Acceptance Criteria of Korea Radioactive Waste Agency (KORAD) so that we could confirm the validity of the PCP. The evaluation item of the PCA is a particulate size verification test. The test is passed only if the component ratio of a particle size below 0.2 mm is less than 15% and the particle size below 0.01 mm is less than 1%. The very first 3 drums passed the test, so we began applying the PCP to whole target drums. In the process of conducting the crush-sieving method in earnest, qualified inspectors based on KNWQAP participated conducting sampling, measuring and checking whether a foreign material was included. They tested samples and packaged drums regarding 5 spheres of general, radiological, physical, chemical and biological characteristic. KNF disposed concrete and refractory brick waste by the crush-sieving method so that KNF could take over 100 drums to KORAD in 2021. But, it is needed to be improved that a dust size below 0.3 mm is generated as a secondary waste which needs to be solidified for the final disposal and the work environment is not good enough because of the dust.

Investigations and monitoring of environmental radiation are important for preventing expected accidents or for early detection of unexpected accidents, in nuclear facilities and the surrounding. In the event of an environmental radiation accident, it should be possible to identify and analyze the radiation-contaminated area. Therefore, a rapid radiation monitoring system is required for immediate response and necessary measures. In this study, the distribution of radiation mapping is performed on a contaminated area using 2-dimensional or 3-dimensional contour mapping techniques. The entire surrounding area can be understood at a glance by displaying the radiation contour line on the map of the measured area.

This facility was developed to investigate the characteristics of metal oxide and to secure operational technology through hydrogen supply to 100 kW capacity transferred arc plasma torch and melting furnace under anoxic conditions. Besides, the emission of pollutants generated during operation was minimized by burning the exhaust gases in the next combustion chamber and by applying a SNCR, a scrubber, etc. The main target object was determined as a metal oxides generated as radioactive wastes when dismantling the nuclear power plant. The metal alloy was produced by supplying hydrogen during the melting process of the metal oxide. The reaction equation is as follows: Fe + M(Metal)On + H2(Gas) → FeM + Slag + H2O In this paper, operating conditions according to the melting temperature and hydrogen supply with iron and metal oxides were investigated, and the chemical characteristics of the alloyed metal and Slag were analyzed. The result of this study can be used as fundamental data for the treatment and disposal of metal wastes.

Laser cutting has been attracting attention as a next-generation tool in application for nuclear decommissioning. It enables high-speed cutting of thick metal objects, and its narrow kerf width greatly reduces the amount of secondary waste compared to other cutting methods. In addition, it only requires the relatively small cutting head without any complicated equipment, and long-distance cutting apart from a laser generator is possible using beam delivery through optical fiber. And there is almost no reaction force because it is non-contact thermal cutting. For these reasons, the laser cutting is very advantageous for remote cutting. In laser cutting, the irradiated laser power is absorbed and consumed to melt the material of the cutting target. When the applied laser power is greater than the power consumed for melting, the residual power is transmitted to the back of the cut object. This residual power may unintentionally cut or damage undesired objects located behind the cutting target. In order to prevent this, it is necessary to adjust the laser power for each thickness of the target object to be cut, or to increase the distance between the cut target and the surrounding structures so that the transmitted power density can be sufficiently lowered. In this work, safety study on residual power that penetrates laser-cut objects was conducted. Experimental studies were performed to find safe conditions for irradiation power density that does not cause surface damage to the stainless steel by adjusting the laser power and stand-off distance from the target.

This study introduces the licensing process carried out by the regulatory body for construction and operation of the 2nd phase low level radioactive waste disposal facility in Gyeongju. Also, this study presents the experience and lessons learned from this regulatory review for preparing the license review for the next 3rd phase landfill disposal facility. Korea Radioactive Waste Agency (KORAD) submitted a license application to Nuclear Safety and Security commission (NSSC) on December 24, 2015 to obtain permit for construction and operation of the national engineered shallow land disposal facility at Wolsong, Gyeongju. NSSC and Korea Institute of Nuclear Safety (KINS) started the regulatory review process with an initial docket review of the KORAD application including Safety Analysis Report, Radiological Environmental Report and Safety Administration Rules. After reflecting the results of the docket review, the safety review of revised 10 application documents began on November 29, 2016. Total 856 queries and requests for additional information were elicited by thorough technical review until November 16, 2021. As the Gyeongju and Pohang earthquakes occurred in September 2016 and November 2017, respectively, the seismic design of the disposal facility for vault and underground gallery was enhanced from 0.2 g to 0.3 g and the site safety evaluation including groundwater characteristics was re-investigated due to earthquake-induced fault. Also, post-closure safety assessments related to normal/abnormal/human intrusion scenarios were re-performed for reflecting the results of site and design characteristics. Finally, NSSC decided to grant a license of the 2nd phase low level radioactive waste disposal facility under the Nuclear Safety Laws in July 2022. This study introduces important issues and major improvements in terms of safety during the review process and presents the lessons learned from the experience of regulatory review process.

Waste containers for packaging, transportation and disposal of NPP (Nuclear Power Plant) decommissioning wastes are being developed. In this study, drop tests were conducted to prove the safety of containers for packaging of the wastes and to verify the reliability of the analysis results by comparing the test and analysis results. The drop height of the waste containers was considered to be 30 mm, which is the maximum lifting speed of a 50 tons crane in the waste treatment facility converted to the drop height. Drop orientation of the containers was considered for bottom-end on drop. The impact acceleration and strain data were obtained to verify the reliability of the analysis results. Before and after the drop tests, measurement of the dose rate and the radiographic testing for concrete wall, and measurement of the wall thickness of steel plate were conducted to evaluate the radiation shielding integrity. Also, measurement of bolt torque, and visual inspection were conducted to evaluate the loss or dispersion of radioactive contents. After the drop tests, the radiation dose rate on the container surface did not increase by more than 20%, and there was no crack in the concrete. In addition, the thickness of the steel plate did not change within the measurement error. Therefore, the radiation shielding integrity of the container was maintained. After the drop tests, the lid bolts were not damaged and there was no loss of pretension in the lid bolts. In addition, there was no loss or dispersion of the contents as a result of visual inspection. In order to prove the reliability of the drop analysis results, safety verifications were performed using the drop test results, and the appropriate conservatism for the analysis results and the validity of the analysis model were confirmed. Therefore, the structural integrity of the waste containers was maintained under the drop test conditions.

According to the ‘Regulations on the Delivery of Low and Medium Level Radioactive Waste’, Notification No. 2021-26 of the Nuclear Safety and Security Commission, a history of radioactive waste and a total amount of radioactivity in a drum are mandatory. At this time, the inventory of radionuclides that make up more than 95% of the total radioactivity contained in the waste drum should be identified, including the radioactivity of H-3, C-14, Fe-55, Co-58, Co-60, Ni-59, Ni-63, Sr- 90, Nb-94, Tc-99, I-129, Cs-137, Ce-144, and total alpha. Among nuclides to be identified, gamma-emitting nuclides are usually analyzed with a gamma ray spectrometer such as HPGe. When a specific gamma-ray is measured with a detector, several types of peaks generated by recombination or scattering of electrons are simultaneously detected in addition to the corresponding gamma-ray in gamma-ray spectroscopy. Among them, the full energy peak efficiency (FEPE) with the total gamma energy is used for equipment calibration. However, this total energy peak efficiency may not be accurately measured due to the coincidence summing effect. There are two types of coincidence summing: Random and True. The random coincidence summing occurs when two or more gamma particles emitted from multiple nuclides are simultaneously absorbed within the dead time of the detector, and this effect becomes stronger as the counting rate increases. The true coincidence summing is caused by simultaneous absorption of gamma particles emitted by two or more consecutive energy levels transitioning from single nuclide within the dead time of the detector. This effect is independent of the counting rate but affected by the geometry and absolute efficiency of the detector. The FEPE decreases and the peak count of region where the energy of gamma particles is combined increases when the coincidence summing occurs. At the Radioactive Waste Chemical Analysis Center, KAERI, samples with a dead time of 5% or more are diluted and re-measured in order to reduce the random coincidence summing when evaluating the gamma nuclide inventory of radioactive waste. In addition, a certain distance is placed between the sample and the detector during measurement to reduce the true coincidence summing. In this study, we evaluate the coincidence summing effect in our apparatus for the measurement of radioactive waste samples.

High Integrity Container (HIC) made of polymer concrete was developed for the efficient treatment and safe disposal of radioactive spent resin and concentrate waste in consideration of the disposal requirements of domestic disposal sites. Permission for application of Polymer Concrete High Integrity Container (PC-HIC) to the domestic nuclear power plants (NPPs) has been completed or is under examination by the regulatory agency. In the case of 860 L PC-HIC for very-low-level-waste (VLLW) or low low-level-waste (LLW), the application of four representative NPPs has been approved, and the license for extended application to the rest NPPs is also almost completed. A licensing review is also underway to apply 510 L PC-HIC for intermediate and low-level-waste (ILLW) to representative nuclear power plants. In order to handle and efficiently store and manage PC-HICs and high-dose PCHIC packages, a gripper device that can be remotely operated and has excellent safety is essential, and the introduction of NPPs is urgent. The conventional gripper device developed by the PC-HIC manufacturer for lifting test to evaluate the structural integrity of PC-HIC requires a rather wide storage interval due to its design features, and does not have a passive safety design to handle heavy materials safely. In addition, work convenience needs to be reinforced for safety management of high radiation work. Therefore, we developed a conceptual design for a gripper device with a new concept to minimize the work space by reflecting on-site opinions on the handling and storage management conditions of radioactive waste in NPPs, and to enhances work safety with the passive safety design by the weight of the package and the function of checking the normal seating of the device and the normal operation of the grip by the detector/indicator, and to greatly improves the work efficiency and convenience with the wireless power supply function by rechargeable battery and the remote control function by camera and wireless monitoring & control system. Through design review by experts in mechanical system, power supply and instrumentation & control fields and further investigations on the usage conditions of PC-HICs, it is planned to facilitate preparations for the application of PC-HIC to domestic NPPs by securing the technical basis for a gripper device that can be used safely and efficiently and seeking ways to introduce it in a timely manner.

Strong acidic wastewater containing a radionuclide is generated from the decontamination of radioactively contaminated wastes or equipment. This wastewater is generally treated though a precipitation process using an alkali (alkali earth) hydroxides. In this precipitation process, a significant amount of alkali (alkali earth) sulfates are generated, which is the reason for the increase in the radioactive waste generation. In this study, a method for separating only radionuclides and metal ions from the wastewater was evaluated. For this reason, precipitation behaviors of radionuclides and metal ions by hydrazine injections were investigated using equilibrium calculations. In addition, behaviors of hydrazine decomposition after removal of radionuclides and metal ions were analyzed for recycling the wastewater.

Se-79, a fission product of uranium, is present in spent nuclear fuel. Selenium is volatilized from the spent nuclear fuel during the pretreatment of pyroprocessing, and a filter composed of calcium oxide can capture gaseous selenium in the form of CaSeO3. Because Se-79 has a long half-life (3.27E5 years) and selenite ions have high mobility in groundwater, they must be immobilized in a chemically stable form for final disposal. This study used a composition of 50 TeO2 - 10 Al2O3 - 10 B2O3 - 10 Na2O - 10 CaO - 10 ZnO (mol%). High-purity powders of TeO2, Al2O3, H3BO3, Na2CO3, CaCO3, and ZnO were used as glass precursors. The mixed powders were placed in alumina crucibles and melted in an electric furnace under an ambient atmosphere at 800°C for 1 h before being cast on a carbon mold. The obtained glasses were ground into fine powders and then mixed with CaSeO3 powders. The powders were melted in alumina crucibles at 800°C for 1 h. To simulate a seleniumcaptured calcium filter, CaSeO3 was synthesized by a precipitation method using sodium selenite (Na2SeO3) and calcium nitrate (Ca(NO3)2) solutions. The glass samples were analyzed by an X-ray diffractometer (XRD). Retention of Se in tellurite glasses was analyzed by an X-ray fluorescence spectrometer (XRF) and inductively coupled plasma (ICP). The chemical durability of tellurite glass was evaluated through the PCT method.