In order to test the applicability of bunker-A in a diesel engine for small-fishing boat, the investigation of the engine performance and the exhaust emission was performed under various conditions of fuel property, intake air pressure and fuel temperature. It was also performed based on IMO NOx Technical code. At high load, the energy consumption rate of bunker-A was lower than that of diesel oil, and the characteristics of exhaust emission of bunker-A were similar to those, and NOx emission rates of both fuels satisfied the IMO NOx emission regulation limits. The energy consumption rate and characteristics of exhaust emission were improved as the intake air pressure was increased, but these were not improved remarkably as the temperature of bunker-A was heated. However, at low load the energy consumption rate, CO emission rate and HC emission rate of bunker-A were higher than those of diesel oil, but NOx emission rates of the fuels were about the same. In addition, at low load the energy consumption rate and CO emission rate of bunker-A were increased as the intake air pressure and the temperature were higher than normal conditions. Accordingly, it is thought that the use of bunker-A in a kind of test engine is possible at high load. On the other hand, it is thought that more research is needed to improve the combustion efficiency under low temperature and low load condition.

This study was conducted on the properties of exhaust emissions of diesel oil and fish oil blended with diesel oils using a direct injection diesel engine at different loads, and on the conditions of carbon deposits of diesel oil and 40% blend oil in the combustion chamber after 20 hours operation at 1]2 load. The properties of exhaust emissions by fish oil blended with diesel oils showed no significant difference with diesel oil. However, soot emissions decreased, increasing the ratio of fish oil. Carbon deposits by fish oil blended with diesel oils were high level compared with diesel oil, which might be overcome by preheating of fuel oil and operating conditions.

The combustion characteristics of diesel oil and fish oil blended with diesel oils were investigated at various blending rate of fish oil in diesel engine and constant volume combustion bomb. The evaporation and combustion duration of diesel oil and fish oil blended with diesel oils were respectively different high and low temperature. The dependence of ignition delay on the temperature was different in high and low temperature ranges which were divided at the 773K. The ignition delay become longer than that of diesel oil as the blending rate of fish oil increases, and its difference were larger at different loads. The densityof smoke was lower as the blending rate of fish oil increases, and the rate offuel consumption showed no significant difference between diesel oil and fish oil blended with diesel oils.

저손실 망간징크 페라이트에서 CaO-SiO2첨가는 입계에 높은 전기저항층을 형성시켜 와류에 의한 손실을 감소시키는 것으로 알려져 있다. 본 실험에서는 Nb2O5 를 제 3의 첨가제로 사용하여 저손실 망간징크 페라이트에서의 전자기적 물성변화를 관찰하였다. Nb2O5 300ppm 이상 첨가시 부분적인 과대입자 성장이 관찰되었으며, 200ppm 첨가시 CaO-SiO2만 첨가한 시편에 비하여 밀도가 증가하였다. Nb2O5 첨가시에는 100ppm 이하의 SiO2첨가에서 우수한 전력손실 특성이 나타났으며, 고온 소결시 Nb2O5-CaO를 첨가한 시편에서 낮은 전력손실을 나타내었다.

The combustion characteristics, ignition delay, p-t, dp/dt, Q-t of diesel oil and fish oil blended diesel oils was investigated according to pressure and temperature in a constant volume combustion bomb. The results are as follows: 1) The influence of temperature and pressure on the ignition delay was almost constant in high temperature, regardless of the blending rates, and the ignition delay was shortest in the 60% blend. 2) The maximum pressure was high in order of with pure diesel oil, with the 20% blend and the 60% blend. 3) The rate of pressure rise was high in order of with pure diesel oil, with the 20% blend and the 60% blend. The rate of maximum pressure rise was significantly higher with pure diesel oil than with two blends. 4) The amount of accumulative heat release was large in order of with pure diesel oil, with the 20% blend and the 60% blend.

In this paper, combustion characteristics and engine performance varying with blending rate of fish oil using five test fuels, e.g.pure diesel oil and four types of sardine-oil-blended diesel oils, their blending rates by weight being 20%, 40%, 60% and 80% respectively, and operating condition of engine, were investigated experimentally both in the constant volume combustion bomb and in the engine. The results are summarized as follows: 1) In the bomb, the influence of temperature on ignition delay of sardine-oil-blended diesel oils was larger than that of pure diesel oil, and it tended to increase as the blending rate of fish oil increase sardine-oil-blended diesel oils. As far as the influence of pressure on ignition delay concerns, there was no significant difference with all the test fuels. 2) In the engine, the ignition delay of fish-oil- blended diesel oils was longer than that of pure diesel oil, and it tended to increase as the blending rate increases. In the bomb, the ignition delay in high temperature showed no significant difference between with pure diesel oil and with fish-oil-blended diesel oils, and it was especially short with 60% fish-oil-blended diesel oil. In low temperature, however, the delay became longer as the blending rate increase. 3) The combustion duration was shorter with fish-oil-blended diesel oils than with pure diesel oil and it became a little shorter as the blending rate increases. 4) The rate of fuel consumption showed no significant difference between with fish-oil-blended diesel oils and with prue diesel oil, although calorific value of fish oil was lower than that of diesel oil. 5) Smoke density in exhaust gas was lower with fish-oil-blended diesel oils than with pure diesel oil and the higher the blending rate was, the lower the smoke density became

직교이방향 이층 유리섬유 강화 Epoxy 수지를 사용하여 인장축에 대해 섬유방향이 0˚, 15˚, 25˚ 및 45˚인 시료로 인장시험 및 전기절연 강도시험을 통하여 얻은 결과는 다음과 같다. 1) 섬유방향이 인장축에 대해 0˚에서 45˚로 증가함에 따라 항복응력 및 파단응력은 감소하는 경향이고 특히 0˚와 15˚ 사이에서 급격한 변화율을 보인다. 2) 파단시 변화율은 인장방향에 대한 섬유방향이 45˚인 경우 최대치를 나타냈고 15˚~45˚ 범위에서 급격한 변화율을 보인다. 3)섬유의 방향이 동일할 경우 인장력을 많이 받은 시료일수록 최대절연강도 값은 낮아졌고 인장방향과 섬유방향의 교각이 증가할수록 최대절연강도 값을 나타내는 압축응력의 값은 낮은 점으로 이동하는 경향을 보였다. 4) 기계적 특성과 같이 섬유방향이 45˚인 경우의 시료가 가장 나쁜 전기적 절연강도 특성을 나타냈다.