In this study, a high speed Rigid Inflatable Boat(RIB) with about 10 meters length is developed. Design speed of the boat is 30 knots (15.43 m/s) using 250 hp twin engines and main material is aluminum. Resistance performance related to the free running attitude as trim and sinkage are discussed and wave patterns are observed to make clear the relationship between the performance and wave characteristics using model test and CFD analysis. The results show that not only wave patterns but also free running attitude of the boat have a strong influence on resistance performance. CFD results including free surface give good relative tendency for effective power and the attitude comparing model test results. CFD analysis used in this study can be used at initial ship design stage of high speed boat.

본 연구에서는 쌍동선체의 선수형상에 대해 일반적으로 적용되고 있는 재래식과 선수 돌출의 반전형 선수 형상에 대한 저항성능 및 항주자세를 수치해석을 통해 분석하고, 반전형 선수형상에 대해서는 모형시험을 통하여 수치해석과 비교분석하였다. 반전형 선수형상은 재래식 선수형상보다 선수 발산파 파정의 생성위치를 선미방향으로 이동시켜 개선된 조파현상을 보였으며, 저항 및 안정된 항주 자세 결정에 효과적이며 선체 저항이 약 2.95% 개선되었다. 반전형 선수형상에 대한 수치해석 및 모형시험 비교분석 자료는 향후 선형설계 활용에 유용할 것으로 판단된다.

본 논문의 주 목적은 전산유체역학(CFD)을 바탕으로 어선에 부착된 빌지킬의 치수 파라미터에 대한 저항성능 맵(MAP)을 작성 하는 것이다. 치수 파라미터 스터디에는 빌지킬의 길이 3가지와 폭 3가지를 선정하여 9가지로 구성하였다. 현존선에 부착된 빌지킬의 길이는 배 길이 대비 약 90 %이고, 폭은 배 폭 대비 약 5 %이다. 수행항목은 빌지킬 길이는 배 길이 대비 63 %, 77%, 90% 그리고 빌지킬 폭은 5%, 7 %, 9 %로 구성하였다. CFD 를 이용하여 9가지 빌지킬에 대하여 실선의 유효마력을 추정하였다. 현존선을 기준으로 길이가 제일 짧고 폭이 제일 긴 빌지킬의 경우 0.3% 감소된 결과를 보여주었다. 길이와 폭 모두가 가장 긴 빌지킬의 경우 1.7% 증가된 결과를 보여주었 다. 길이와 폭 모두가 가장 짧은 빌지킬의 경우 2.3 % 감소된 결과를 보여주었다. 이 맵은 저항성능 관점에서 해당 어선의 이동 및 조업 패턴에 따른 최적의 부가물 치수 선정에 활용 가능하다.

In this study, a 30ft class high speed catamaran cruise boat is designed and resistance performances are investigated by model test at a circulating water tank. Design speed of the boat is 17knots(8.7m/s) and maximum speed is 20knots(10.3m/s) using 330ps twin engine. Each single bodies are designed unsymmetric planing hull considering high speed-length-ratio(Froude number) and wave interaction at inner part of the hull. Small size fins like chine are attached near free surface at each outside of the hull to separate wave along the hull side. The results show that the small chine plays a big role in separating the wave flowing along the hull. However, in the case of relatively heavy boat such as the developed hull, such a small power due to chine can not cause additional lift and cause resistance increase.

In this thesis, it was considered that in durability characteristics of concrete pavements evaluation of strength characteristics as well as abrasion resistance is important as the domestic concrete pavements couldn't fulfill the public needs and cases of damage are increasing. In order to solve such problems, it is intended to compare the abrasion resistance in accordance with the mixing rate of admixtures (silica fume and polymer powder) which are incorporated in the upper layer of two-lift concrete pavement and find the optimum mixing rate for abrasion resistance by focusing on the high performance of concrete pavements through two-lift concrete pavements which use cellular sprayed concrete construction method. Both test results, which were performed based on ASTM C 779 B (dressing wheel abrasion test method) and ASTM C 944 (rotary cutter method) standards in accordance with silica fume and polymer powder mixing rate that was incorporated in the upper layer of two-lift concrete pavement, proofed that the abrasion resistance increased as the mixing rate of silica fume and polymer powder increased. However, it was also confirmed that if the mixing rate of admixtures is excessively increased it will not have an effect and it will rather decrease the abrasion resistance.

연·근해어선들은 운항 또는 조업시 안정성(복원성능 및 횡동요 저감 성능)을 향상시키기 위해 여러 가지 부가물을 설치하며, 일반적으로 Fig. 1과 같이 세 가지로 분류할 수 있다. Bare hull을 포함하여 각 부가물이 단독으로 부착된 경우 3가지, 복수의 조합으로 부착된 경우 3가지 그리고 3가지 모두 부착된 1가지에 대하여 수치 계산을 수행하였다. Table 1은 Bare hull에 대한 주요치수를 나타낸 것이고, Table 2는 3가지 부가물에 대한 주요치수를 기술하였다. 3가지 선체 부가물에 대하여 CFD에 의한 유체동역학적 성능을 평가하였다. 각각의 부가물에 대하여 단독, 2개씩 조합된 복수 그리고 3개 모두 부착된 경우에 대하여 평가를 하였다. 1번 부가물의 경우 압력저항이 마찰저항 보다 차지하는 비율이 큼을 알 수 있었다. 2번과 3번 부가물의 경우 압력저항과 마찰저항이 거의 대동소이 함을 알 수 있었다. 복수조합과 3가지 모두 부착된 경우 부가물 상호간의 상관관계는 매우 작음을 알 수 있었다. 11노트에서 2번 부가물과 모든 부가물이 부착된 경우 유효마력 관점에서 약 9 % 차이를 보였다.

The purpose of this study was to investigate the resistance performance and the sensitivity of the panels placed on the free surface of the water using the potential-based Rankine source panel method. The potential-based Rankine source panel method was applied to predict a flow phenomena around a ship and the exact nonlinear free surface boundary conditions were adopted. The trim and sinkage state of the ship also were taken into account. In order to deal with complex geometries of the planing ship the panel cutting method was adopted. The R/V Athena ship was adopted as the high speed ship. Numerical analysis was carried out by systematically changing the range and number of panels in the free surface area, and the results were compared with each other.

PURPOSES : This purpose of this study is to analyze the effect to autogenous shrinkage of the top-layer material of a two-lift concrete pavement mixing both silica fume and polymer powder. METHODS: The bottom-layer of a two-lift concrete pavement was paved with original portland cement (OPC) with a 20~23 cm thickness. Additionally, the top-layer which is directly exposed to the environment and vehicles was paved with a high-performance concrete (HPC) with a 7~10 cm thickness. These types of pavements can achieve a long service life by reducing joint damage and increasing the abrasion and scaling resistance. In order to integrate the different bottom and top layer materials, autogenous shrinkage tests were performed in this study according to the mixing ratio of silica fume and polymer powder, which are the admixture of the top-layer material. RESULTS: Autogenous shrinkage decreased when polymer powder was used in the mix. Contrary to this, autogenous shrinkage tended to rise with increasing silica fume content. However, the effects were not significant when small amounts of polymer powder were used (3% and 11%). CONCLUSIONS : The durability and compressive strength increase when silica fume is used in the mix. The flexural strength considerably increases and autogenous shrinkage of concrete decreases when polymer powder is used in the mix. As seen from above, the proper use of these materials improves not only durability, but also autogenous shrinkage, leading to better shrinkage crack control in the concrete.

The improvement of resistance performance for the 4.99 ton class fishing boats was shown. The 4.99 ton fishing boats are the most commonly used one in the Korean coastal region. The evaluation of resistance performance was estimated by the Computational Fluid Dynamics (CFD) analysis. The CFD simulation was performed by the validation for various types of bow shapes on the hull. The optimized hull form from the simulation was selected and showed the best resistance performance. This hull type was tested on the towing tank in the National Institute of Fisheries Science (NIFS). The effective horsepower (EHP) was estimated by the resistance test on the towing tank with the bare hull condition. The drag force on the three service speed conditions was obtained for the resistance analysis to power prediction. The measured drag forces are compared with the results from the CFD simulation with one another. As results of the model tests, it was confirmed that the shape of the bow is an important factor in the resistance performance. The effective horsepower decreased about 30% in comparison with the conventional hull form. Also, the resistance performance improved the reduction of required horsepower, which especially contributed to the energy-saving for the fisheries industry. In the CFD analysis, the resistance performance improved slightly. In this case, the ratio of the residual resistance (CR) in the total resistance (CT) was high. Therefore, the CFD analysis was not enough to satisfy with reflection for the free surface and wave form in the CFD procedure. Both model test and CFD calculation in this study can be applied to the initial design process for the coastal fishing vessel.

최근 테러에 대한 위험성의 증가로 대중들의 폭발 피해에 대한 인식이 증가하였다. 우리나라에 방폭 설계에 대한 기준이 미흡하며, 현재 적용하고 있는 방폭 설계도 정적해석으로 건물의 안정성 및 경제성을 위해 방폭 설계를 개발해야 하는 상황 이다. 또한 지진 발생 증가로 내진 설계 의무화가 확대된 가운데 방폭 설계를 하지 않고 내진 설계를 적용한 부재의 방폭 성능을 판단을 연구한다. 현재 보편적인 폭발 하중의 해석 방법은 UFC 3-340-02 매뉴얼을 참고하는 것이다. UFC 3-340-02 매뉴얼을 통한 폭발 하중의 특성을 적용하고 KBC 2016의 내진 상세를 적용한 보를 등가 단자유도 시스템으로 변환하여 폭발 저항 성능을 연구하였다. 보통, 중간, 특수 모멘트 골조의 연성 능력에 대한 최대 처짐을 고려하여 폭발물의 이격 거리를 통해 평가하여 내진 상세 적용 시 폭발 저항 성능이 향상된다는 것을 입증하였다.

This study aims to establish a seismic resistance performance evaluation method that makes sure to secure the seismic resistance performance of the existing mid-low story reinforced concrete structures. This study focuses on the development of the seismic resistance performance evaluation method for the overall seismic resistance performance evaluation on the buildings by applying fuzzy theory. This seismic resistance performance evaluation method considers the mutual relations among the type of force, the type of member, the type of story, and the states of deterioration of the buildings. The total seismic resistance performance index from this method was calculated by the intensity weight of each evaluation item, fuzzy measure, fuzzy integration. Moreover, the evaluation methodology was established in this study to identify the performance level of the Immediate Occupancy, Life Safe, Collapse Prevention by applying the fuzzy theory.

본 연구에서는 연륙연도 사업에 대응하는 경제성 및 안정성을 갖춘 쌍동선형 차도선의 개발을 위해 U형과 V형의 서로 다른 쌍 동선형을 CFD 해석을 수행하여 저항성능을 비교하였다. CFD 해석 결과 U형 쌍동선형의 경우 14kts 이상의 고속에서 선수부 파형에 이상 이 발생하여 정상적인 운행이 불가능하다 판단되었으며, 이에 비해 V형은 동일한 속도에서도 이상이 발생하지 않았으며, 또한 U형 쌍동선 형 대비 V형 쌍동선형의 경우, 저속에서는 U형 대비 높은 침수표면적에도 불구하고 거의 같은 RTS값을 보이지만, 고속으로 넘어가면 U형 에 비해 확연히 낮은 RTS값을 보임을 확인, V형의 쌍동선형이 U형에 비해 저항성능이 개선됨을 확인하였다.