The adsorption process using GAC is one of the most secured methods to remove of phosphate from solution. This study was conducted by impregnating Cu(II) to GAC(GAC-Cu) to enhance phosphate adsorption for GAC. In the preparation of GAC-Cu, increasing the concentration of Cu(II) increased the phosphate uptake, confirming the effect of Cu(II) on phosphate uptake. A pH experiment was conducted at pH 4-8 to investigate the effect of the solution pH. Decrease of phosphate removal efficiency was found with increase of pH for both adsorbents, but the reduction rate of GAC-Cu slowed, indicating electrostatic interaction and coordinating bonding were simultaneously involved in phosphate removal. The adsorption was analyzed by Langmuir and Freundlich isotherm to determine the maximum phosphate uptake(qm) and adsorption mechanism. According to correlation of determination(R2), Freundlich isotherm model showed a better fit than Langmuir isotherm model. Based on the negative values of qm, Langmuir adsorption constant(b), and the value of 1/n, phosphate adsorption was shown to be unfavorable and favorable for GAC and GAC-Cu, respectively. The attempt of the linearization of each isotherm obtained very poor R2. Batch kinetic tests verified that ~30% and ~90 phosphate adsorptions were completed within 1 h and 24 h, respectively. Pseudo second order(PSO) model showed more suitable than pseudo first order(PFO) because of higher R2. Regardless of type of kinetic model, GAC-Cu obtained higher constant of reaction(K) than GAC.

This research aims to study the effect of impregnation ratio and activation temperature on microporous development of activated carbon (AC). Rubberwood chips, which are wasted from home furnishing industry, were used as precursors for synthesized of activated carbon by chemical activation employing Potassium hydroxide (KOH) as activation agent. Rubberwood char was carbonized at 400 °C for 1 h under inert gas. In this experiment, the rubberwood chars were impregnated with KOH solution by 1:1–3 (char: KOH) impregnation ratio for 24 h, then the samples were activation at 600–800 °C. Surface area, pore volume, micropore volume, pore size distribution, adsorption isotherm and porous structure were analyzed in this experiment to identify the properties of derived activated carbon. According to the investigation, the activated carbon, activated at 800 °C with impregnation ratio of 1:3, demonstrated the highest surface area, pore volume and micropore volume as 1491.75 m2/g, 0.6777 cm3/g, and 0.5813 cm3/g, respectively. Its average pore size was 1.82 nm and it also showed type I adsorption isotherm which indicates as microporous solid.

In this report, we incorporate activated carbon (AC) onto aluminum substrate via doctor blade method to produce an all-solid-state supercapacitor. The electrochemical properties of the all-solid-state supercapacitor were characterized by cyclic voltammetry and electrochemical impedance spectroscopy. Galvanostatic charge/discharge tests also were carried out to exhibit stability of the AC-based supercapacitor. The impedance and charge/discharge curves of the all-solid-state supercapacitor showed good capacitive behavior after functionalized AC. The highest specific capacitance obtained for the AC-based supercapacitor was 106 F g−1. About 160% of specific capacitance increased after functionalization of the AC, which indicated that modification of the AC by nitric acid was able to introduce functional groups on the AC and improve its electrochemical performances.

Pyrolysis fuel oil (PFO) is used for the manufacturing of high-purity pitch for carbon precursor due to its high carbon content, high aromaticity, and low heterogeneous element and impurity content. Pitch is commonly classified with its softening point, which is most considerable physical property affecting to various characteristics of the carbon materials based on pitch, such as electrical and thermal conductivity, mechanical strength, and pore property. Hence, the softening point should be controlled to apply pitch to produce various carbon materials for different applications. Previous studies introduce reforming process under high pressure and two step heat treatment for the synthesis of pitch with high softening point from PFO. These methods lead to a high process cost; therefore, it is necessary to develop a process to synthesize the pitch with high softening point by using energy effective process at a low temperature. In this study, waste polyethylene terephthalate (PET) was added to control the softening point of PFO-based pitch. The pitch synthesized by the heat treatment with the addition of PET showed the softening point higher than that of the pitch synthesized with only PFO. The softening point of PFObased pitch synthesized at 420 °C was 138.3 °C, while that of the pitch synthesized by adding PET under the same process conditions was 342.8 °C. It is proposed that the effect of the PET addition on the increase in the softening point was due to the radicals generated from thermal degradation of PET. The radicals from PET react with the PFO molecules to promote the polymerization and finally increase the molecular weight and softening point of the pitch. In addition, activated carbon was prepared by using the pitch synthesized by adding PET, and the results showed that the specific surface area of the activated carbon increased by the addition of PET. It is expected that the pitch synthesis method with PET addition significantly contributes to the manufacture of pitch and activated carbon.

Biomass of agricultural waste is getting increasing attention all over the world as it is a kind of renewable, abundantly available, low cost, and environmentally friendly resource. Preparation of activated carbon from agricultural waste via microwave-assisted chemical agent activation. The porosity, surface area, and functional and surface chemistry were featured by means of low-temperature nitrogen adsorption, Scanning Electron Microscopy, (SEM) and Fourier Transform Infrared Spectroscopy (FTIR). The best conditions resulted in activated carbon with adsorption capacity of 517.5 mg/g and carbon yield of 80.99%. The activated carbons from carbonized tobacco stem with K2CO3 activation by microwave radiation is highest of surface area, and total pore volume corresponded to 2557 m2/g, and 1.647 cm3/g, respectively, with a high contribution of mesopores, microwave power of 700 W, and irradiation time of 30 min. The results of the review showed that chemical activation could develop both microporosity and mesoporosity. The findings support the potential to prepare high surface area and micropore-activated carbon from agricultural waste by microwave-induced chemical activation.

This work reports utilization of apple leaves as a source of activated carbon. Activated carbon from apple leaves is prepared by two different methods, thermal activation where AC1 is obtained and chemical activation using H3PO4 and ZnCl2 where AC2 and AC3 are obtained, respectively. XRD analysis revealed that all types of prepared ACs have a semi-crystalline nature with a mean crystallite size of 13, 21.02, and 39.47 nm for AC1, AC2, and AC3, respectively. To identify the most suitable desorption temperature, the exothermic behavior was discovered for the three types of ACs by DSC. The exothermic onset temperatures are 340 °C, 200 °C, 400 °C, or AC1, AC2, and AC3, respectively. The point of zero charge for the three types of ACs is 8.6, 7.3, and 2.5 for AC1, AC2, and AC3, respectively. The BET surface area analysis data demonstrated that mesoporous structure was developed in AC1 and AC2, while a microporous structure was developed in AC3. Quantum chemical calculations for ACs is carried out using Density Functional Theory (DFT). Application of the prepared ACs in adsorption of basic dye C.I. base blue 47 is studied. The maximum removal efficiency was 65.1%, 96% and 99% for AC1, AC2, and AC3, respectively under the influence of different operating aspects. Adsorption data are modeled by Langmuir, Freundlich, and Temkin isotherms. The data revealed that adsorption of basic dye C.I. base blue 47 on AC1 follows Langmuir isotherm and adsorption on AC2 and AC3 follows Freundlich isotherm.

In this study, Fe3O4/ MgO/Activated carbon composite was used to remove arsenic ion (As (III)) from aqueous media. To this end, Frangula Alnus was used to prepare activated carbon (AC) by calcination in the furnace at 700 °C for 4 h and was then used to synthesize the MgO/Fe3O4/AC composite. To study the surface properties of the composite, various analyses such as SEM, EDX/Mapping, FTIR, DLS, BET and VSM were applied. According to the BET analysis, the specific surface area and average pore size of the Fe3O4/ MgO/AC composite were obtained as 190.92 m2/g and 7.57 nm, respectively, which showed that the aforementioned nanocomposite had a mesoporos structure with an excellent specific surface area. Also, VSM analysis indicated that the composite had a superparamagnetic property and could be easily separated from the solution by a magnet. Moreover, the results of the As (III) sorption indicated that the highest uptake efficiency was obtained 96.65% at pH = 7, adsorbent dosage = 0.13 g/L, t = 35 min, T = 45 °C and Co = 6 mg/L. In addition, the pseudo-second-order model could better describe the kinetic behavior of the sorption process. Furthermore, Langmuir model was the best model to describe the equilibroium behavior of the As(III) ion sorption. Besides, according to the the thermodynamic study, enthalpy change and entropy change were obtained 58.11 kJ/mol and 224.49 J/mol.K, respectively, indicating that the sorption process was spontaneous and endothermic. According to the results, the Fe3O4/ MgO/AC composite was a good adsorbent with the extraordinary properties, which can be used on an industrial scale.

This work reveals a modified method for the preparation of activated carbon (P-ACA) using low-cost materials (mix natural asphalt: polypropylene waste). The P-ACA was prepared at 600 °C by assisting KOH and HF. The morphological variations and chemical species of the P-ACA were characterized using SEM–EDX and FTIR. The active surface area, density and ash content of the P-ACA were also investigated. Adsorption properties of P-ACA were used for the thermodynamic and kinetic study of 4-((2-hydroxy naphthalenyl) diazenyl) antipyrine (HNDA), which was prepared as a novel azo dye in this work. The optimal conditions (initial concentration, adsorbent dose, contact time and temperature) of the adsorption process were determined. Adsorption isotherms (Freundlich and Langmuir) were applied to the experimental data. These isothermal constants were used to describe the nature of the adsorption system, and the type of interaction between the dye and the P-ACA surface. The results have indicated that the mixture (Natural asphalt-polypropylene waste) is efficient for the synthesis of P-ACA. The synthesized P-ACA demonstrates the presence of pores on the surface with various diameter ranges (from 1.4 to 4.5 μm). Furthermore, P-ACA exhibits an active surface area of 1230 m2 g−1, and shows a high adsorption capacity for HNDA.

제 4 차 산업혁명이 일어남에 따라 각국의 정부와 기업들은 보다 환경친화적인 정책과 기술 개발에 힘쓰고 있다. 배기가스 배출과 소음이 거의 없는 전기차 및 수소차의 개발, 그리고 이를 보편화 하기 위한 정부의 정책 등 기존의 경제, 산업 구조를 친환경적으로 바꾸려는 시도가 많이 이루어지고 있다. 최근 여러 환경문제를 해결하기 위해 각종 유해 가스 흡착 및 폐수 처리용으로 활성탄을 많이 사용하고 있으나 흡착질의 특성에 따라 요구되는 표면 특성이 다르기 때문에 수요에 걸맞는 활성탄의 개발이 점차 요구되고 있는 실정이다. 따라서 본 연구에서는 친수성 유기물 제거에 유리한 활성탄을 개발하고자 C-O, C-O-C, C=O 및 O=C-O 등과 같은 친수성 작용기를 질산처리 방법을 통해 활성탄 표면에 효과적으로 도입하는 연구를 진행하였다. 질산을 활용하여 끓는점 및 다양한 농도 조건에서 활성탄을 환류, 개질하였고, 이를 세척 후 고온에서 탄화시켜 활성탄의 표면을 개질하였다. 제조된 개질활성탄은 활성탄의 비표면적, mesopore 및 micropore 의 함량을 알기 위하여 BET 를 이용하여 측정하였고, 4 M 120 ℃에서 개질한 결과 가장 높은 792.22 m2g-1 으로 확인되었다. 또한 제조된 활성탄의 표면 및 기공 특성 변화를 확인하기 위해 SEM, XPS, EDX, BET 등의 분석을 실시하였으며 질산 처리 정도에 따른 특성 변화에 대해 비교 고찰하였다.

Mango fruit seed shells were used as starting materials to produce activated carbons for the capture of acetone, a typical volatile organic compound (VOC), from gaseous streams. This fruit waste presents high volatiles and low ashes contents, as expected for the lignocelulosic materials commonly used for the preparation of activated carbons. The starting material was hydrothermally treated at 180 or 250 °C for 5 h and the obtained hydrochars were activated with KOH solutions. The carbon samples were characterized by SEM, EDX, TG/DTA, Raman spectroscopy and textural analysis by physisorption. The adsorption capacity and adsorption cycles were investigated by TG. The hydrochars presented spherical morphology and the activated carbons derived from them presented heterogeneous micropore structures allowing to high capacity of acetone vapor removal, namely 472 mg/g, at 30 °C and 363 mg/g, at 50 °C. The results indicate that the adsorption capacity of the activated carbons is directly related to their Dubinin-Astakhov micropore surface areas and microporous volumes determined by NLDFT. The adsorption of acetone vapor showed a pseudo-first order kinetics and both external and intraparticle transport contributed for the overall process. Highly efficient and stable acetone vapor removal was observed over the activated carbons after five cycles.

The discharge of dye-containing industrial effluents such as methylene blue (MB) in water bodies has resulted in severe aquatic and human life problems. In addition to this factor, there is the accumulation of banana peel wastes, which can generate ecological damage. Thus, this research purpose a different method from the literature using the banana peel waste (BP) to produce activated carbon (ACBP) by NaOH activation followed by pyrolysis at 400 °C to remove methylene blue (MB). The material was characterized by TGA, XRD, SEM, BET, and FTIR. The influence of dye concentration (10, 25, 50, 100, 250, and 500 mg L−1) was investigated. ACBP presented a well-developed pore structure with a predominance of mesopores and macropores. This morphological structure directly influences the MB removal capacity. The highest efficiency for dye removal was in the MB initial concentration of 25 mg L−1, sorbent of 0.03 g, and contact time of 60 min, which were 99.8%. The adsorption isotherms were well defined by Langmuir, Freundlich, and Temkin isotherm models. The Langmuir model represented the best fit of experimental data for ACBP with a maximum adsorption capacity of 232.5 mg g−1. This adsorbent showed a comparatively high performance to some previous works. So, the banana peel waste is an efficient resource for producing activated carbon and the adsorption of methylene blue.

Preparation of activated carbon from biomass residue with conventional steam activation was conducted to find the alternative raw materials for meeting the high demand for low-cost porous material in the desiccant application. In this study, activated carbons were produced from dead camphor leaves using two-step methods at different preparation temperatures. The characterization results revealed that the prepared activated carbons have a surface area of 700 m2/g, with 75% of microporosity. The water vapor sorption study reported that the water uptake of camphor leaf-based activated carbons was strongly affected by the pore properties of the materials. Moreover, from the water adsorption kinetics, it was observed that the rate constant of adsorption was varied at each relative pressure, which can be assumed that the water adsorption mechanism is different at each relative pressure. From these results, it was revealed that the prepared camphor leaf-based activated carbons have a promising ability to adsorb water vapor from humid air.

Spent Calgon Filtrasorb activated carbon (SAC) from glycerine deodorization unit was evaluated for the removal of methylene blue (MB). The SAC was used without further modification. The SAC was characterized for BET surface area, pH, pHpzc and FTIR to determine the textural and chemical properties of SAC. The batch adsorption study of MB was carried out under different initial concentrations (5–500 mg/L), pH (2–11) and contact time (0–200 h). The SAC was found to have high BET surface area, pore volume and average pore diameter of 735 m2/g, 0.292 cm3/g and 2.56 nm, respectively. The properties of SAC contributed to high MB adsorption capacity of 283 mg/g. The equilibrium data fitted well with Langmuir model, indicating monolayer adsorption; while the activation energy (Ea) of Dubinin–Radushkevitch (D–R) model is lower than 8 kJ/mol, signifying physisorption. The adsorption kinetics was best illustrated by pseudo-second-order model, while the intraparticle diffusion and Boyd models suggested that film diffusion is the rate-controlling step. These findings showed that Calgon Filtrasorb SAC from glycerine deodorization unit can be potentially reused an adsorbent for the removal of dyes.

The carbon spheres (CSs) synthesized by an ultrasonic-spray pyrolysis method were activated for supercapacitor electrode. There are plenty of cracks on the surface of the activated carbon spheres (ACSs), which expend with increasing the activation temperature and activator dosage. The specific capacitance of ACSs increases with the activation temperature and activator dosage and reach to maximal value at certain conditions. Importantly, the ACS sample activated at relatively low activation temperature (600 °C) and 7 of mass ratio of KOH to CSs has the highest specific capacitance (about 209 F g− 1 at 50 mA g− 1 of current density) and indicates the excellent cycling stability after 1000 consecutive charge–discharge cycles. Furthermore, the graphene sheets could be found in the samples that were activated at 1000 °C. And the electrode prepared by the sample has the very low series resistance because of the excellent conductivity of the formed graphene sheets.

Abstract In this study, we investigated that the activated carbon (AC)-based supercapacitor and introduced SIFSIX-3-Ni as a porous conducting additive to increase its electrochemical performances of AC/SIFSIX-3-Ni composite-based supercapacitor. The AC/SIFSIX-3-Ni composites are coated onto the aluminum substrate using the doctor blade method and conducted an ion-gel electrolyte to produce a symmetrical supercapacitor. The electrochemical properties of the AC/SIFSIX-3-Ni composite-based supercapacitor are evaluated through cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and galvanostatic charge/discharge tests (GCD). The AC/SIFSIX-3-Ni composite-based supercapacitor showed reasonable capacitive behavior in various electrochemical measurements, including CV, EIS, and GCD. The highest specific capacitance of the AC/SIFSIX-3-Ni composite-based supercapacitor was 129 F g−1 at 20 mV s−1.

The purpose of this study was to remove lead and arsenic ions from aqueous solutions using the activated carbon prepared from Citrus limon tree leaves. Characteristics of the prepared adsorbent were studied thoroughly using BET, SEM, EDS and mapping, XRD, and RAMAN analyses. The results of experiments showed that the highest adsorption efficiencies were 97.67% and 95.89% for Pb (II) and As (III), respectively. Additionally, the adsorbent was successfully regenerated four times and therefore it was able to perform the adsorption and desorption processes well. Moreover, the results of adsorption kinetics showed that the pseudo second-order kinetic model was more effective for the description of adsorption mechanism of both metals. Furthermore, the equilibrium studies indicated that Langmuir and Freundlich isotherm models were desirable for lead and arsenic ions, respectively.

A simulation based (DFT) study is performed on activated 2D-carbon sheet without and with vacancies of central carbon atoms, and explored the electronic properties. The inter-atomic distance at the center of activated carbon sheet is gradually increased with increasing number of vacancies. We get lower binding energy with three vacancies, and higher without a vacancy. A covalent bond is found between C–C atoms, density of states exhibit a semiconductor nature of a system without vacancy, and metallic nature in the presence of vacancies. There are higher peaks of resultant anti-bonding states with three vacancy system and it exhibits higher amorphous nature which causes higher electron concentration, mobility and higher electrical conductivity.

In the current work, we have developed a new composite catalyst for methanol oxidation based on Ni and/or NiO incorporated in activated carbon (AC) derived from agricultural wastes (Rice straw). The new electrocatalysts based on nickel-activated carbon (Ni/AC) and nickel oxide-activated carbon (NiO/AC) composites were prepared by electroless plating technique. Physico-chemical characteristics of the composites such as structure, composition and morphology were studied by X-ray diffraction (XRD), Fourier transform infrared spectrometer (FTIR), scanning electron microscopy (SEM), energy dispersive X-ray (EDX), and particle size analyzer. The electrochemical activity of the prepared composites towards methanol electrooxidation reaction (MOR) has been evaluated under alkaline conditions by cyclic voltammetry, linear sweep voltammetry, and chronoamperometry. Among the examined electrodes, the electrochemical performance of NiO/AC preceded either Ni/ AC or Ni free AC and showed better stability. The dispersion of different forms of Ni in activated carbon in case of NiO/AC electrode is predicted to give rise to the increase in electrocatalytic activity in the potential range under study and makes it more resistant to poisoning by the byproduct of methanol oxidation. The effect of changing methanol concentrations and scan rates on the electrochemical characteristics of the modified electrode was studied and it was found that the diffusion process is controlled by methanol rather than OH− ions.

Increasing ambient carbon dioxide ( CO2) concentration from anthropogenic greenhouse gas emission has contributed to the growing rate of global land and ocean surface temperature. Various carbon capture and storage (CCS) technologies were established to mitigate this impending issue. CO2 adsorption is gaining prominence since unlike traditional chemical absorption, it does not require high energy usage for solvent regeneration and consumption of corrosive chemical solvent. In CO2 adsorption, activated carbons show high CO2 adsorption capacity given their well-developed porous structures. Numerous researches employed oil palm wastes as low-cost precursors. This paper provides a comprehensive assessment of research works available thus far in oil palm-derived activated carbon (OPdAC) for CO2 adsorption application. First, we present the desired OPdAC characteristics and its precursors in terms of their chemical properties, elemental, and proximate compositions. This is followed by an overview of various activation methodologies and surface modification methods to attain the desired characteristics for CO2 adsorption. Then the focus turned to present available OPdAC CO2 adsorption performance and how it is affected by its physical and chemical characteristics. Based on these, we identify the challenges and the potential development in different aspects such as precursor selection, process development, and optimization of parameter. A pilot scale production cost analysis is also presented to compare various activation and surface modification methods, so that the appropriate method can be selected for CO2 adsorption.

The effects of activated carbon originated Ballasted Flocculant (BF) on the settleability of activated sludge and the recovery of BF by Hydro-cyclone (HC) were analyzed experimentally. Two kinds of BF (M-I: 125-250 μm, M-II: 250-425 μm in dia.) and three kinds of activated sludges with different SS concentration (2,300-7,100 mg/L) were applied for this study. With the dosage variation of BF from 0.14 to 1.3 g-BF/g-SS, we could obtain 24-31% improvement in SV30 (Sludge Volume after 30min sedimentation) for the lowest SS concentration sludge (2,300 mg/L). Whereas the SV30 improvement was much higher as 44-48% for the highest SS concentration sludge (7,100 mg/L). The settling characteristics of the sludge with BF followed Vesilind model the best among three models (Vesilind, Takacs and Cho model). HC could effectively separate BF with the separation efficiency of 70-90% and over 95% separation efficiency could be obtained when the HC was applied twice.