SAFCs are recently being highlighted to overcome the disadvantages of AFCs. According to the recent works, alkaline doped PBI membranes exhibited good ionic conductivity, acceptable mechanical strength and high thermal stability. Suitable ionomer binder solutions for SAFCs were necessary. In this study, QPBIs having quaternized intermediate MGMC in the side group were synthesized for use as anion conducting ionomer binder. In addition, crosslinker was added in the catalyst slurry to improve the mechanical strength and chemical stability. The QPBIs were investigated in terms of FT-IR, NMR, ionic conductivity, KOH uptake etc. Moreover, MEAs prepared with different amounts of ionomer binder in electrodes were evaluated by CV and IV curve.

고분자전해질 연료전지용 막-전극접합체 내 전극에는 삼상계면을 구성하기 위하여 이온 전도가 가능한 이오노머가 함유되어야한다. 따라서 촉매슬러리 제조를 위해 이오노머가 용매 시스템에 분산되어 있는 분산 용액 형태이어야 한다. 하지만 상용 이오노머 분산 용액의 종류가 제한되어 있으며 개발 물질로 제 조된 전해질막과의 호환성을 위해 동일 물질 기반의 분산 용액으로의 전환이 요구된다. 본 연구에서는 동결 건조 방식을 활용한 고분자 분쇄방법을 도입하여 이오노머를 분쇄하고 이를 활용한 이오노머 분쇄 용액을 제조하여 다양한 물성 및 성능을 조사하였다.

술폰화 폴리아릴렌에테르술폰(SPAES) 랜덤 공중합체는 고분자 전해질 연료전지에 적용될 때 높은 수소이온전도 도, 상대적으로 낮은 생산 단가 그리고 열화학적 저항성등과 같은 장점을 갖는다. 반면, SPAES 공중합체는 가혹한 구동 조건 하에서 낮은 화학적 안정성과 치수 불안전성으로 인해 실제 연료전지 막에 직접적으로 적용하는데 어려움이 있다. 그에 타당 한 해결책은 SPAES 공중합체를 상호 연결된 기공 구조와 높은 열화학적 강도를 가지는 지지체 필름(예 : 전기방사된 폴리이 미드 지지체)에 함침시키는 것이다. 본 연구에서는 함침막 제조를 위한 이오노머로 빠른 이온 수송을 위해 높은 자유 체적을 유도하는 회전 그룹을 갖는 SPAES 공중합체를 선택하였다. 제작된 막의 실용가능성은 막 특성화를 통해 평가되었다.

고분자전해질막은 전극 이외에 전기 화학 연료전지의 성능을 결정하는 중요한 요소이다. 고분자전해질막은 가스나 양성자 등의 작은 분자를 선택적으로 수송해야 한다. 고분자전해질막을 투과한 가스는 급속히 전기 화학적 환원을 발생시켜 음극 촉매의 열화를 유발하기 때문에 수소 장벽으로 작동해야 하며 가능한 한 빨리 양성자를 이동시켜야 한다. 지금까지 고분자전해질막의 수소 기체 투과도를 측정하는데 한정된 방법(예 : Constant volume/variable pressure (Time-lag)법)을 사용 했다. 그러나 측정의 대부분은 고분자전해질막은 건조된 진공 하에서 이루어진다. 그렇지 않으면 얻어진 수소 투과도는 측정 오차가 커지는 원인이 되기 쉽다. 이 연구에서는 일반적으로 고분자전해질막으로 사용되는 Nafion212의 수소 가스 투과 특성을 온도와 습도가 동시에 제어되는 in-situ 측정 시스템을 이용하여 평가하였다.

연료전지는 화석연료, 특히 내연기관을 대체할 수 있는 가장 대표전인 에너지 기술이다. 가장 중요한 핵심 재료 중 하나로서 연료기체의 장벽 역할을 함과 동시에 수소이온전달 역할을 하는 고분자 전해질 막(PEM)이 있다. PEM 내부에서 수화 채널은 수소이온의 전달통로 역할을 하기 때문에, 많은 연구자들은 높은 함수율을 저가습 상태에서도 유지하여 우수한 수소이온 전달 능력을 보유할 수 있는 상분리현상을 통한 친수성 채널 형성에 대하여 초점을 맞추어 왔다. 본 총설에서는 이 러한 낮은 가습조건에서도 높은 수소이온전도도를 갖는 술폰화 PEM들의 합성 전략에 대하여 논의 하여보고, 다른 연구자들 의 고성능 탄화수소계 PEM의 설계에 도움을 주고자 하였다.

Sulfonated poly(arylene ether sulfone)(SPAES) random copolymers are representative alternatives to perfluorinated sulfonic acid(PFSA) ionomers used as the state-of-the-art polymer electrolyte membranes for fuel cells. SPAES copolymers have advantages such as low hydrogen permeability, low production cost. However, it is difficult to demonstrate high electrochemical single cell performances for a long period time, since SPAES membranes have critical interfacial issues with catalyst layers containing PFSA ionomers, particularly in the repeated hydrated and dehydrated cycles. In this study, called as radiation grafting of proton conductive polymers on SPAES membranes, is tried in order to improve proton conductivity without a severe loss in dimensional stability and to reduce interfacial resistance with PFSA catalyst layers at the same time.

Sulfonated poly(arylene ether sulfone) (SPAES) random copolymers have been perceived as membrane materials alternative to perfluorinated sulfonic acid (PFSA) ionomers, since they are cheap and chemically tunable when compared with PFSA. Moreover, their relatively low gas permeability, particularly to hydrogen, contributes to reduced thermal decomposition of membrane-electrode assemblies. In spite of their advantages, freestanding SPAES copolymers have critical issues associated with chemical/electrochemical durability as well as interfacial resistance with electrodes. In this study, SPAES-PTFE reinforced membranes are fabricated using consecutive membrane formation protocols, (e.g., SPAES nanodispersion in water-alcohol mixtures, spontaneous pore-filling, and solvent-assisted thermal treatment techniques) and systematically evaluated.

Polymer electrolyte membrane fuel cells (PEFCs) are eco-friendly energy conversion systems to convert hydrogen directly into electricity via an electrocatalytic reaction. Representative membrane materials of PEFCs are Perfluorinated sulfonic acid (PFSA) ionomers including NafionⓇ and 3M ionomers. In spite of high proton conductivity, it is difficult to apply PFSA free-standing membranes in real PEFC applications owing to their weak mechanical failures and thermo-chemical decomposition during PFEC operations, in addition to a relatively high production cost. In this study, Nafion nanodispersions in water-alcohol mixtures are fabricated using a supercritical fluid technique. The fundamental membrane characteristics are compared with those of counterpart membranes obtained from a commercially available Nafion emulsion.

직접 메탄올 연료전지(Direct Methanol Fuel Cells)는 액상의 메탄올을 연료로 직접 사용하는 전기 에너지 전환 장치로서 연료의 값이 싸고 취급이 용이하며 초소형화가 가능하다. Montmorillonite (MMT)가 첨가된 고분자 전해질 분리막의 경우 열적⋅물리적 성질이 개선되며 메탄올 투과도가 감소되는 장점을 가지고 있지만 이온전도도는 감소가 되는 단점을 가지고 있다. 본 연구에서는 술폰산기(-SO3H)를 포함하는 MMT를 제조하여 Sulfonated Poly(arylene ether sulfone)(SPAES) 고분자와 sulfonated MMT(sulMMT)를 혼합하여 유⋅무기 복합막을 제조하고 특성평가가 이루어졌다.

Perfluorinated sulfonic acid (PFSA) ionomers have been widely used for renewable energy generation, including polymer electrolyte fuel cells (PEFCs), owing to their excellent resistance to harsh chemicals and good ion-transport properties. PFSA materials experience critical chemical decomposition to radical attacks, and fast hydrogen crossover leading to fairly reduced electrochemical performances, when they are used as membrane materials. Similar chemical degradation also occurs in PEFC electrodes containing PFSA ionomer binders used as both mechanical supporters and proton conductors and shortens PEFC lifetime. In this study, several approaches based on their morphological rearrangement to overcome these economical and technical issues are proposed. They include pore-filling membrane formation, nanodispersion, and their combination.

Perfluorinated sulfonic acid ionomers have been used as representative membrane materials in a wide range of applications. Though PFSA ionomers have been well known as chemically durable materials, their chemical resistances should be improved further to apply them to practical fuel cell systems operated under harsh conditions. One plausible solution would be to fabricate reinforced membranes composed of proton-conducting ionomers and chemically durable porous support films. In this study, pore-filling membranes are prepared via the impregnation of PFSA ionomers into porous PTFE support films. The objective of this study is to systematically investigate the influences of pore characteristics on proton transport behavior and electrochemical single performances.

Perfluorinated sulfonic acid (PFSA) ionomers have been widely used as membranes in the fields of green power generation and electrolysis. In spite of their high ion-conducting properties, it is difficult to apply them in the freestanding membrane state to harsh operation conditions owing to their chemical and electrochemical degradation issues. A promising membrane concept to satisfy this purpose would be “pore-filling membrane” composed of PFSA ionomers and porous PTFE support films. In this study, the porous PTFE support film treated with a cheap hydrophilic polymer is used as a reinforced material. Interestingly, the resulting PFSA-PTFE pore-filling membranes exhibit an extremely high proton conductivity with a fairly reduced ionomer content, which may give a valuable information to design a desirable pore-filling membrane.

과불소계 술폰화 이오노머(perfluorinated sulfonic acid ionomers; PFSAs)는 뛰어난 수소이온전도성과 높은 내화학성으로 인해 고분자 전해질 연료전지(polymer electrolyte fuel cells)용 고체전해질로 널리 사용되고 있다. 그러나 PFSA 전해질은 가습-건조조건에서 연료전지가 구동에 따라 반복적인 팽윤-수축으로 인해 전극층이 전해질로부터 탈리되어 전기화학적 수명특성이 감소되는 문제점을 가지고 있다. 본 연구에서는 다공성 PTFE support film의 기공특성에 대한 이해를 바탕으 로 기공구조 내 나피온 이오노머를 함침시키는 강화막을 제조하였고, 기본특성을 평가하였다. 제조된 강화막은 매우 높은 수 소이온전도도(~0.5 S cm-1@90°C in liquid water)를 나타내었다.

Much research into fuel cells operating at a temperature below 800℃. is being performed. There are sig-nificant efforts to replace the yttria-stabilized zirconia electrolyte with a doped ceria electrolyte that has high ionic con-ductivity even at a lower temperature. Even if the doped ceria electrolyte has high ionic conductivity, it also shows highelectronic conductivity in a reducing environment, therefore, when used as a solid electrolyte of a fuel cell, the power-generation efficiency and mechanical properties of the fuel cell may be degraded. In this study, gadolinium-doped ceriananopowder with Al2O3 and Mn2O3 as a reinforcing and electron trapping agents were synthesized by ultrasonic pyrol-ysis process. After firing, their microstructure and mechanical and electrical properties were investigated and comparedwith those of pure gadolinium-doped ceria specimen.

In this study, PtRu nanoparticles deposited on binary carbon supports were developed for use in direct methanol fuel cells using carbon blacks (CBs) and multi-walled carbon nanotubes (MWCNTs). The particle sizes and morphological structures of the catalysts were analyzed using X-ray diffraction and transmission electron microscopy, and the PtRu loading content was determined using an inductively coupled plasma-mass spectrometer. The electrocatalytic characteristics for methanol oxidation were evaluated by means of cyclic voltammetry with 1 M CH3OHin a 0.5 MH2SO4 solution as the electrolyte. The PtRu particle sizes and the loading level were found to be dependent on the mixing ratio of the two carbon materials. The electroactivity of the catalysts increased with an increasing MWCNT content, reaching a maximum at 30% MWCNTs, and subsequently decreased. This was attributed to the introduction of MWCNTs as a secondary support, which provided a highly accessible surface area and caused morphological changes in the carbon supports. Consequently, the PtRu nanoparticles deposited on the binary support exhibited better performance than those deposited on the single support, and the best performance was obtained when the mass ratio of CBs to MWCNTs was 70:30.

The bipolar plate is the most important and most costly component of proton exchange membrane fuel cells. The development of a suitable low density bipolar plate is scientif-cally and technically challenging due to the need to maintain high electrical conductivity and mechanical properties. Here, bipolar plates were developed from different particle sizes of natural and expanded graphite with phenolic resin as a polymeric matrix. It was observed that the particle size of the reinforcement significantlyinfluencesthe mechanical and electri-cal properties of a composite bipolar plate. The composite bipolar plate based on expanded graphite gives the desired mechanical and electrical properties as per the US Department of Energy target, with a bulk density of 1.55 g.cm-3 as compared to that of ~1.87 g.cm-3 for a composite plate based on natural graphite (NG). Although the bulk density of the expanded-graphite-based composite plate is ~20% less than that of the NG-based plate, the I-V perfor-mance of the expanded graphite plate is superior to that of the NG plate as a consequence of the higher conductivity. The expanded graphite plate can thus be used as an electromagnetic interference shielding material.

Two types of Pt nanoparticle electrocatalysts were composited on Pt nanowires by a combination of an electrospinning method and an impregnation method with NaBH4 as a reducing agent. The structural properties and electrocatalytic activities for methanol electro-oxidation in direct methanol fuel cells were investigated by means of scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and cyclic voltammetry. In particular, SEM, HRTEM, XRD, and XPS results indicate that the metallic Pt nanoparticles with polycrystalline property are uniformly decorated on the electro-spun Pt nanowires. In order to investigate the catalytic activity of the Pt nanoparticles decorated on the electro-spun Pt nanowires, two types of 20 wt% Pt nanoparticles and 40 wt% Pt nanoparticles decorated on the electro-spun Pt nanowires were fabricated. In addition, for comparison, single Pt nanowires were fabricated via an electrospinning method without an impregnation method. As a result, the cyclic voltammetry and chronoamperometry results demonstrate that the electrode containing 40 wt% Pt nanoparticles exhibits the best catalytic activity for methanol electro-oxidation and the highest electrochemical stability among the single Pt nanowires, the 20 wt% Pt nanoparticles decorated with Pt nanowires, and the 40 wt% Pt nanoparticles decorated with Pt nanowires studied for use in direct methanol fuel cells.

This study is aimed to increase the activity of cathodic catalysts for PEMFCs(Polymer Electrolyte Membrane Fuel Cells). we investigated the temperature effect of 20wt% Pt/C catalysts at five different temperatures. The catalysts were synthesized by using chemical reduction method. Before adding the formaldehyde as reducing agent, process was undergone for 2 hours at the room temperature (RT), 40˚C, 60˚C, 80˚C and 100˚C, respectively. The performances of synthesize catalysts are compared. The electrochemical oxygen reduction reaction (ORR) was studied on 20wt% Pt/C catalysts by using a glassy carbon electrode through cyclic voltammetric curves (CV) in a 1M H2SO4 solution. The ORR specific activities of 20wt% Pt/C catalysts increased to give a relative ORR catalytic activity ordering of 80˚C > 100˚C > 60˚C > 40˚C > RT. Electrochemical active surface area (EAS) was calculated with cyclic voltammetry analysis. Prepared Pt/C (at 80˚C, 100˚C) catalysts has higher ESA than other catalysts. Physical characterization was made by using X-ray diffraction (XRD) and transmission electron microscope (TEM). The TEM images of the carbon supported platinum electrocatalysts (80˚C, 100˚C) showed homogenous particle distribution with particle size of about 2~3.5 nm. We found that a higher reaction temperature resulted in more uniform particle distribution than lower reaction temperature and then the XRD results showed that the crystalline structure of the synthesized catalysts are seen FCC structure.

기존 고분자전해질연료전지(PEMFC)의 단점을 극복하기 위해 고체전해질 알카라인연료전지(SAMFC)가 근래에 많이 연구되고 있다. 본 논문에서는 술폰화 폴리벤지이미다졸(PBI) 유도체를 이용하여 SAMFC용 막을 제조하였다. 술폰화 폴리벤지이미다졸 유도체는 KOH에 의해 쉽게 도핑되고 도핑된 막은 높은 OH-의 전도도와 기계적 강도를 보였다. 특히 sPBI-co-PBI (술폰화 PBI : 비술폰화 PBI = 75 : 25)의 경우, 90℃ 100% 상대습도 하에서 2.98 × 10 -2 S/cm의 높은 OH-의 전도도를 보였다.