한국 고속도로 포장은 1970년 경부고속도로 건설을 시작으로 많은 발전을 이루었으며, 최근 도로이용자에게 쾌적한 도로를 제공할 수 있는 배수성 아스팔트 포장에 대한 관심이 높아지고 있다. 본 연구에서는 한국 고속도로 배수성 아스팔트 구간에 대한 시공목적별, 신설과 유지보수 등을 구분하여 배수성 아스팔트 포장 적용현황을 분석하였다. 또한, 적용된 배수성 아스팔트 포장의 교통량을 조사 분석하였으며, 효율적인 교통량 그룹 선정 방법을 제시하였다. 고속도로에 적용된 배수성 아스팔트 포장의 전주기 평가를 위해 평가항 목을 제시하였다. 내구성평가 항목으로는 포장상태평가지수와 표면조도를 선정하였다. 기능성 평가 항목으로는 내부 공극 막힘여부를 확인할 수 있는 현장투수, 미끄럼저항지수, 포장노면과 타이어에서 발생하는 도로소음원 평가를 위한 도로소음을 선정하였다. 그리고 조사 항목들에 대한 배수성 아스팔트 포장의 전주기 평가를 통해 각각 조사 항목에 대한 정량적 분석평가를 수행하여 도로소음도 예 측식을 제안하였다.

국토교통부는 고속도로 접근성 개선을 통한 지역균형 발전을 위해 남북측과 함께 동서축으로 지속적인 신설 사업을 계획하고 있다. 이에 따라 고속도로 노선의 관리 연장이 증가하고 대부분 산지인 우리나라 지형 특성에 의해 터널 구간도 증가하고 있다. 터널 구간 포장의 경우 환경 조건 등의 영향으로 전이구간에서 파손이 다수 발생하고 있다. 따라서 본 연구에서는 장대터널 구간에서 조사된 PMS 데이터를 분석하여 터널 진입 전 후 PMS 조사 인자별 변화를 분석하였다. 분석 조건은 1) 1km 이상의 장대터널 포장상태조사 자료 분석, 2) SD(Surface Distress), IRI(International Roughness Index), HPCI(Highway Pavement Condition Index) 인자 분석, 3) SD 상세 데이터(균열, 패칭, 스폴링 등) 분석이다. 이를 활용하여 터널 진입 전·후 포장 연장 변화에 대한 분석인자별 변화 검토, 터널 진입 전· 후 분석인자별 평균값 변화 비교, 터널 내 포장의 선형 균열, 패칭, 스폴링 파손 상세 검토를 수행하였다. 분석 결과 터널 진입 후 30~40m 까지 변화가 크게 나타나는 것을 확인하였으며, 평균값 비교 결과 SD 값이 진입 전 후 약 66% 차이가 나타난다. SD 상세데 이터 분석 결과는 균열 및 스폴링 파손 등에 대해 100m 구간 내에 약 3.35m2 정도 패칭보수가 이루어졌다. 장대터널의 경우 터널 입 구와 터널 내부의 환경 조건이 상이하여 전이구간에서 터널 내부보다 파손이 다수 나타나는 것을 확인하였다.

In South Korea, the level of Highway Pavement Management System (HPMS) was developed since early 2000. During this time numbers of professional pavement condition monitoring equipment were developed and applied in the actual field. One of the remarkable results is 3D Pavement condition Monitoring profiler vehicle (3DPM) designed and developed in Korea Expressway Corporation Research Division (KECRD). Thanks to this equipment, The surface condition of current pavement can successfully be monitored and proper following management strategy cab be established. However, the inner condition of pavement layer cannot be monitored dur to limitation of 3DPM equipment. In this paper, Bending Beam Rheometer (BBR) mixture creep test was performed to verify the effectiveness of current 3DPM equipment. It was found that the current 3DPM equipment has reasonable feasibility on surveying pavement condition.

PURPOSES : The evaluation of the low-temperature performance of an asphalt mixture is crucial for mitigating transverse thermal cracking and preventing traffic accidents on expressways. Engineers in pavement agencies must identify and verify the pavement sections that require urgent management. In early 2000, the research division of the Korea Expressway Corporation developed a three-dimensional (3D) pavement condition monitoring profiler vehicle (3DPM) and an advanced infographic (AIG) highway pavement management system computer program. Owing to these efforts, the management of the entire expressway network has become more precise, effective, and efficient. However, current 3DPM and AIG technologies focus only on the pavement surface and not on the entire pavement layer. Over the years, along with monitoring, further strengthening and verification of the feasibility of current 3DPM and AIG technologies by performing extensive mechanical tests and data analyses have been recommended. METHODS : First, the pavement section that required urgent care was selected using the 3DPM and AIG approaches. Second, asphalt mixture cores were acquired from the specified section, and a low-temperature fracture test, semi- circular bending (SCB) test, was performed. The mechanical parameters, energy-release rate, and fracture toughness were computed and compared. RESULTS : As expected, the asphalt mixture cores acquired from the specified pavement section ( poor condition – bad section) exhibited negative fracture performances compared to the control section (good section). CONCLUSIONS : The current 3DPM and AIG approaches in KEC can successfully evaluate and analyze selected pavement conditions. However, more extensive experimental studies and mathematical analyses are required to further strengthen and upgrade current pavement analysis approaches.

PURPOSES : The numeric-based Highway Pavement Management System (HPMS), along with an advanced three-dimensional pavement condition monitoring profiler vehicle (3DPM), in South Korea has presented remarkable advancements in pavement management since the early 2000. Based on these results, visual distress on pavement surfaces can be easily detected and analyzed. Additionally, the entire expressway pavement surface conditions in South Korea can be easily monitored using the current graphical user interface-based advanced information graphic (AIG) approach. Therefore, a critically negative pavement section can be detected and managed more easily and efficiently. However, the actual mechanical performance of the selected pavement layer still needs to be investigated in a more thorough manner not only to provide more accurate pavement performance results but also to verify the feasibility of the current 3DPM and AIG approaches. In this study, the low-temperature performance of the selected asphalt pavement layer section was evaluated to further verify and strengthen the feasibility of the current 3DPM and AIG approaches developed by the Korea Expressway Corporation. METHODS : Based on 3DPM and AIG approach, the positive and negative-riding-quality road sections were selected, respectively. The asphalt material cores were extracted from each section then bending beam rheometer mixture creep test was performed to measure their low-temperature properties. Based on the experimental results, thermal stress results were computed and visually compared. RESULTS : As expected, the asphalt material from the negative driving performance section presented a poorer low-temperature cracking resistance than that from the positive driving performance section. CONCLUSIONS : Current 3DPM equipment can successfully evaluate expressway surface conditions and the corresponding material performance quality. However, more extensive experimental studies are recommended to verify and strengthen the findings of this study

PURPOSES : The actual service life of repair methods applied to cement concrete pavement is analyzed based on de-icing agent usage. METHODS : Highway PMS data pertaining to de-icing agent usage are classified into three grades: low (1~5 ton/lane/year), medium (5~8 ton/lane/year), and high (greater than 8 ton/lane/year). The repair methods considered include diamond grinding, patching, joint repair, partial depth repair, and asphalt overlay on five major highways. The service life of each repair method is analyzed based on the usage level of the de-icing agent. RESULTS : The service lives of the applied repair methods are much shorter than expected. It is confirmed that the service life afforded by diamond grinding, patching, and joint repair methods are not significantly affected by the use of de-icing agents, whereas that afforded by asphalt overlay and partial depth repair methods is affected significantly. The service life afforded by the asphalt overlay and partial depth repair methods decreases at high usage levels of the de-icing agent (greater than 8 ton/lane/year). CONCLUSIONS : Among the repair methods considered, the service life afforded by partial depth repair and asphalt overlay is affected significantly by the amount of de-icing agent used. Additionally, the differences between the expected and actual analyzed service lives should be considered in the next-generation maintenance strategy for cement concrete pavements.

PURPOSES : This study analyzes the service life of the repair methods of jointed plain concrete pavement (JPCP) on expressways in Korea using PMS data. METHODS : The Korea Expressway Corporation PMS data acquired from five major expressways in Korea were used for the analysis. The service lives of the repair methods were considered for two different cases: 1) the previous repair methods had been completely rerepaired by another or the same method due to their damage, and 2) the current repair methods were still in use. RESULTS : The service lives of D/G and section repair were shown to be at least 30 % and 50 % shorter than expected, respectively. Joint sealing and crack sealing exhibited a service life similar to that expected. The Mill-and-Asphalt-overlay method showed an approximately 30 % longer service life; this might be because some damage to the asphalt overlay is typically neglected until subsequent maintenance and repair. When multiple repairs were applied in series for an identical pavement section, the service life of repairs on previously damaged secti ons become even shorter compared to their first application. CONCLUSIONS : It was found that the analyzed service life of most important repair methods did not reach the expected service life, and that the service life of the same repair method becomes shorter as applied to the previously repaired concrete pavement sections. These shorter service lives should be seriously considered in future JPCP repair strategy development.