In this study, FLUENT v.16.1 was used to investigate the compressible flow generated by the supersonic jet spewed from a high pressure tube. As the boundary condition for CFD (Computational Fluid Dynamics) analysis, the inlet temperature of air was constantly 300 K and the variation of JPR (Jet Pressure Ratio) were 5, 50, 100, 150 and the variation of tube diameter were 10, 20, 30 cm. As a result, it was confirmed that the effective range was increased as the JPR was higher, but it was confirmed that the effective range was lower than the JPR rise, and that the effective range was increased as the diameter was larger. Therefore, it is found that the tube diameter is more sensitive than the JPR among the influence factors of jet, and if the result of this study were reflected in the design of high pressure system, it will contribute to the design of the system for preventing the second accident.

The refrigerant temperature of a compressor increases due to heat generated in the discharge chamber and the motor. The increase of the suction temperature raises the superheat resulting in EER reduction. Thus, accurate superheat prediction is needed for the design of an efficient compressor. In this paper, the unsteady flow analysis is performed using CFD to predict the superheat. The results show that the suction temperature increases by about 26 °C which agrees well with the experiments.

Abstract The increase of the superheat is one of several factors adversely affecting the efficiency of the refrigeration cycle. To this end, it is important to release the heat inside the compressor. Therefore, in this paper, we have increased the convective heat transfer coefficient inside the compressor by utilizing the vibration of the moving part of the compressor. The results show that reducing the gap between the shell and the moving part increases the flow velocity in the gap resulting in the increase of convective heat transfer coefficient.

In this paper, the current of ECV block is connected to compressor crankcase on which the Pc port of Ps port Euro is formed(Type-1). Pc Port Internal Bellows are supposed to be affected by changes at the flow of refrigerant to the solenoid valve inside inhalation. There is Ps port at the direction of flow characteristic in predicting and analyzing. At suction pressures of 0.2MPa and 1.5MPa, maximum flow rates become 46m/s and 129m/s respectively. The refrigerant is discharged by compressor rotation around the axis of rotation from the inflow of port(Pd)(Type-2). By predicting and analyzing inlet flow, suction pressures become 2.7MPa and 3.6 MPa when maximum flow rates of 177.5m/s and 205m/s are affected on Pc ports of Euros with pressures of 1.2KPa and 3.8KPa respectively. This study result can be applied as the basic data for design of ECV.

The behavior of the flow about gas atomizers with a supersonic nozzle containing an under-expanded or over-expanded jet is very important with respect to performance and stability characteristics. Since detailed experiments are expensive, computational fluid mechanics have been applied recently to various relating flow field. In this study, a higher order upwind method with the 3rd order MUSCL type TVD scheme is used to solve the full Reynolds Wavier-Stokes equations. To delineate the purely exhaust jet effects, the melt flow is not considered. Comparison is made with some experimental data in terms of density fields. The influence of the exhaust-jet-to freestream pressure ratio and the effect of the protrusion length of the melt orifice are studied. The present study leads us to believe that the computational fluid mechanics should be considered as powerful tool in predicting the gas atomizer flows.

본 연구는 콘크리트 구조물의 균열 및 유지보수에 대한 문제점을 개선시키기 위한 연구의 일환으로 자기치유형 고상캡슐 (PCC)의 대체율에 따른 모르타르 플로우 및 압축강도를 측정·분석 하였다.

This study evaluated the fluidity and compressive strength of concrete by replacement ratio of blast furnace slag fine aggregate and ferronickel slag fine aggregate to investigate the possibility of replacing natural fine aggregate with steel slag for fine aggregate. Test results show that the use of steel slag fine aggregate improves the fluidity of concrete and compressive strength of concrete was higher than plain concrete.

The study investigated the fluidity and compressive strength properties of cement paste containing Ferro-Nickel slag powder by different curing conditions to estimate the applicability of Ferro-Nickel slag powder for cement replacement materials.

This study is to primarily investigate the consistency and compressive strength of an in-fill slurry of the SIFCON-based HPFRCC according to the mixing time. The mixing time considered were 10, 15 and 20 minutes.

Greenhouse gas emissions, ranking the world's top 10 ranked Korea in the development of the related technologies and the relevant laws and the formulation of plans in 2008 to a low-carbon, green growth a new vision of national growth is accelerating. In addition, Cement substitute material developed using high-performance concrete cement reduction technology, carbon capture technology is being studied. Therefore, in this study, utilizing activated industrial byproducts carbon Absorbing for road materials developed as part of the study typical industrial byproducts, Blast Furnace Slag and calcium hydroxide, sodium silicate mortar on Fundamental Properties of experiments the flow experiments, the compressive strength experiments performed basic experiments with respect to the results obtained were investigated