Four types of high Mn TWIP(Twinning Induced Plasticity) steels were fabricated by varying the Mn and Al content, and the tensile properties were measured at various strain rates and temperatures. An examination of the tensile properties at room temperature revealed an increase in strength with increasing strain rate because mobile dislocations interacted rapidly with the dislocations in localized regions, whereas elongation and the number of serrations decreased. The strength decreased with increasing temperature, whereas the elongation increased. A martensitic transformation occurred in the 18Mn, 22Mn and 18Mn1.6Al steels tested at −196 oC due to a decrease in the stacking fault energies with decreasing temperature. An examination of the tensile properties at −196 oC showed that the strength of the non-Al added high Mn TWIP steels was high, whereas the elongation was low because of the martensitic transformation and brittle fracture mode. Although a martensitic transformation did not occur in the 18Mn1.9Al steel, the strength increased with decreasing temperature because many twins formed in the early stages of the tensile test and interacted rapidly with the dislocations.

The dissertation is on the measurement of the strain caused by the characteristics and the temperature changes of the TIG welded zone which is used with 3D ESPI system that is functionally modified through the laser ESPI system. Experimental results have derived from the fact that the welded zone has micro crack during the various phased of the process such as rolling, alkali cleaning, air cooling and heat processing due to the repetitious up-and-down of the temperature. Especially, both 60℃ and 90℃ are selected to measure the strain on the welded zone which can be effected by these two temperatures in the manufacturing process. The flat plate differences between ESPI and the strain gage are within 2 %, and they are the exactly same with the results from the temperature changes of 60 ℃ and 90 ℃, and also within 3 % and 4 %. As the tensile load increase, the strain of aluminum material increases linearly. Also the same effect are observed as the temperature goes up with irregular-line type. The comparison of the strain by ESPI and the strain gage in the welded specimen is within the 2.6% when it is under the room temperature and low-load conditions, while it is measured within 3 % under the high load condition.

높은 포장온도는 아스팔트포장 소성변형의 주요인이나 소성변형을 줄이기 위한 방안으로서 포장온도를 줄이는 측면에서는 아직 많은 연구가 이루어지지 않은 실정이다. 본 연구에서는 소성변형결함을 줄이기 위한 하나의 대안으로, 온도저감 효과가 있는 것으로 알려져 있는 보수성 포장을 배수성 포장의 하부층에 설치한 포장의 공용특성을 연구하였다. 본 연구의 목적은 보수형 배수성 포장의 온도저감효과를 정량화하고, 포장가속시험(Accelerated Pavement Testing)을 이용하여 온도 저감에 따른 소성변형 감소효과를 확인하고, 정량화하는데 있다. 또한 추가적으로 보수성 포장의 상대강도계수를 분석하고, 일반 포장과 비교하여 설계법 적용시 포장두께를 줄일 수 있는지 여부를 알아보고자 하였다. 본 연구를 위해 보수형 배수성포장 2개 단면 및 일반 배수성 포장 1개 단면 등 총 3개 시험구간이 시공되었다. 히팅 및 살수를 일정주기로 실시하였으며 하중조건은 윤하중 8.2ton, 타이어 공기압 7.03kgf/cm2 타이어 접지면적 610cm2이었다. 이 연구에서 포장체 온도저감효과는 중간층의 경우 6.6~7.9℃(평균7.4℃), 표층의 경우 7.9~9.8℃(평균 8.8℃)였으며, 이를 통해 포장표면의 소성변형 발생을 26% 감소시킬 수 있었다. 또한 탄성계수로부터 추정된 보수성 포장의 상대강도계수는 0.173으로 일반 밀입도 포장의 1.2배 정도였으며, 일반배수성 포장 구간에서는 표층, 중간층, 기층 모두 소성변형이 발생한데 반해 보수형 배수성 포장 구간에서는 표층에서 대부분의 소성변형이 발생된 것으로 나타났다.

Distributed optical fiber sensors have been developed to detect the occurrence of structural anomalies such as excessive stresses, cracks, and leaks at arbitrary locations in the facility. In this paper, we demonstrate fiber optic OFDR (Optical Frequency Domian Reflectometry) sensor to measure strain and temperature through the sensing optical fiber. A PVC pipe was prepared to show the strain measurement performance with a sensing optical fiber attached on the pipe. Also, a temperature test was performed with a sensing optical fiber located in a temperature chamber. In the results, this sensor can operate to resolve 14.2 micro strain and 1.62 degree temperature at the condition of 5 cm spatial resolution.