This study developed a coupled fluid-thermal analysis method for a liquid hydrogen control valve system. Using ANSYS CFX, a transient CFD analysis was performed for the control valve system, including MLI, and the thermal analysis was linked to evaluate the insulation performance of MLI. The analysis examined the pressure distribution, turbulent viscosity, and heat flux at the inlet and outlet, revealing that the highest heat flux occurred in MLI 2. This research is expected to contribute to improving the thermal shielding performance and efficient insulation design of liquid hydrogen storage systems.

In this study, the heat flow characteristics of wave heat exchanger was investigated by being applied to the white smoke reduction system. Through numerical analysis, the heat transfer and flow characteristics of the wave heat exchanger with the change of inlet condition of air-side and water-side were analyzed. To investigate the temperature, the absolute humidity, heat transfer rate, pressure drop and turbulence characteristics of the wave heat exchanger, the simulation analysis was conducted by using the commercial computational fluid dynamics software (Solidworks Flow Simulation) under uniform flow conditions. As the inflow rate of air decreased and the inflow temperature of water increased, the heat transfer coefficient of the wave heat exchanger decreased. When the experimental conditions of water-side were the same, the air outlet temperature and absolute humidity of the wave heat exchanger increased with increasing inflow rate of air. To reduce the white smoke, the air outlet temperature and absolute humidity of the wave heat exchanger must be reduced. Therefore, the lower the air velocity and the water inflow temperature into the wave heat exchanger, the more effective it is.

The heat transfer characteristics of a louver fin for a radiator are numerically analyzed to investigate the performance of radiator for automotive. The commercial code FLUENT is utilized to simulate a louver fin to analyze both the flow fields of air and the solid region of lover fin. The numerical analysis is performed with the variation of air mass flow rate. The results show that as mass flow rate increases, louver fin efficiency is nearly constant. The correlation of the average Nu is derived. The results of numerical study is useful in louvered fin design.

3차원 실내공간의 상부에서 일정유속이 유입하여 양측면 하부쪽으로 유출될 경우, 책상형의 가열 장애물 영향에 의한 유동장의 변화와 온도분포를 수치계산 한 결과 다음과 같은 결론을 얻었다. (1)표준 k-ε 2 방정식 모델로 난류유동장을 해석한 결과 장애물을 기준으로 상하부에는 독립적인 큰 재순환 영역이 존재함을 알 수 있었다. (2) 유입류의 속도 변화에 따른 전제적인 유동패턴은 큰 변화없이 상사적인 분포를 하는 것을 알 수 있었다. (3) 유입속도가 감소함에 따라서, 공간에 대한 발열체의 온도영향이 커진다. (4) Re수가 작은 범위 (10 상(4)-10 상(5)에서는 열전달이 급격히 상승하여, Re수가 10 상(5)이상이 도면 열전달이 거의 일정하다.

For material recovery of black carbon and pyrolysis oil, pyrolysis is considered as an alternative to combustion-based technologies for treatment of waste tire. This study investigated the heat transfer optimization in a pyrolysis reactor for waste tire chips with a capacity of 24 t/d. The reactor was required to have a larger heat transfer rate from hot gas to tire chips in the early stage of pyrolysis, whereas the rate in the later stage should be lower. This was to prevent thermal cracking of heavy compounds in the pyrolysis vapor and to improve the quality of black carbon. CFD was applied to analyze the flow and heat transfer in the complex geometry of the reactor for a total of nine design cases. It was found that modifications to control the distribution of gas flow rate along the reactor are more effective for the present reactor than adjusting the measures for heat transfer enhancement (such as fins). The ideal design improvement was to divide the reactor into two gas sections for a separate control of the flow rate, and to remove the fins of which its alignment perpendicular to the flow inhibits the hot gas from approaching the tube of tire chips.