Crystal structure of the L12 type (Al,X)3Ti alloy (X = Cr,Cu) is analyzed by X-ray diffractometry and the nonuniform strain behavior at high temperature is investigated. The lattice constants for the L12 type (Al,X)3Ti alloys decrease in the order of the atomic number of the substituted atom X, and the hardness tends to increase. In a compressive test at around 473K for Al67.5Ti25Cr7.5, Al65Ti25Cr10 and Al62.5Ti25Cu12.5 alloys, it is found that the stress-strain curves showed serration, and deformation rate dependence appeared. It is assumed that the generation of serration is due to dynamic strain aging caused by the diffusion of solute atoms. As a result, activation energy of 60-95 kJ/mol is obtained. This process does not require direct involvement. In order to investigate the generation of serrations in detail, compression tests are carried out under various conditions. As a result, in the strain rate range of this experiment, serration is found to occur after 470K at a certain critical strain. The critical strain increases as the strain rate increases at constant temperature, and the critical strain tends to decrease as temperature rises under constant strain rate. This tendency is common to all alloys produced. In the case of this alloy system, the serration at around 473K corresponds to the case in which the dislocation velocity is faster than the diffusion rate of interstitial solute atoms at low temperature.

This study was carried out to investigate the effect of W substitution on the precipitation behavior of χ and σ phases in super duplex stainless steel. The χ phase was precipitated at the interface of ferrite / austenite phases and inside the ferrite phase at the initial stage of aging. With an increase in the aging time, the volume fraction of the χ phase increased, and then decreased with the transformation from the χ phase to the σ phase. The σ phase was precipitated later than the χ phase, and the volume fraction of x phase increased with the increase in the aging time. The ferrite phase was decomposed into the new austenite (γ2) and σ phases by aging treatment. The decomposition of the ferrite phase into the γ2 and σ phases was retarded by W substitution for Mo. The volume fraction of the χ phase increased and that of the σ phase decreased due to W substitution. The χ and σ phases were intermetallic compounds, which had lower nickel concentration, and higher chromium, molybdenum, and tungsten concentrations. The χ phase has higher molybdenum and tungsten concentrations than those of the σ phase. The amounts of chromium and nickel in the χ and σ phases did not change, but these phases have higher concentrations of molybdenum and tungsten due to W substitution for Mo.

In this study, the experiments were carried out in order that flexural behavior evaluated High-strength Concrete Beams reinfrced with FRP plates according ro replacement ration of recycled aggregate. As a result, maximum load was higher than existiong of unreinforced when the reinforced with FRP plates and no decrease in load about increased fo replacement ration of recycled aggregate. Some specimens was greater than ACI 440-2R referemce value.

이 연구에서는 고로슬래그 미분말을 사용한 프리캐스트 보의 전단성능에 대하여 평가하였다. 실험체는 고로슬래그 미분말 치환율에 따라 총 4체의 실험체를 제작하였다. 모든 실험체는 전단경간비 2.5, 보의 폭 200mm, 유효깊이 300mm이며, 3점 가력을 받는 단순보로 계획하였다. 또한 이 연구에서는 실험체의 전단강도를 예측하기 위하여 기존 전단강도 예측식을 이용하여 실험결과와 비교하였으며, 총 89개의 기존 전단 실험결과를 이용하여 실험결과와 비교 분석하였다. 실험결과, 고로슬래그 미분말을 치환한 실험체는 포틀랜드 시멘트만을 사용한 실험체와 비교분석한 결과 유사한 전단성능을 나타내었다.

본 연구는 순환굵은골재 콘크리트의 활용성 증대 및 규준 정립에 관한 연구의 일환으로 순환굵은골재 치환율에 따른 고강도 철근콘크리트 보의 휨 특성을 검토하고자 한다. 실험은 콘크리트 설계강도 40MPa, 50MPa, 60MPa 순환굵은골재 치환율 0%, 30%, 50%, 100%를변수로 총 12개의 실험체를 제작하여 최종 파괴 시까지 변위제어 방식에 의해 2점 가력하였다. 실험결과 천연골재를 사용한 실험체와 비교시 균열발생 및 파괴양상의 경우, 순환굵은골재를 사용한 철근콘크리트 보의 실험체는 천연골재 철근콘크리트 보 실험체에 비해 균열이 비교적 압축측까지 진전하는 특성을 보였으나 전반적으로 균열양상은 유사하게 나타났으며, KCI 설계기준식에 의한 계산값 및 실험결과의 비교결과 순환굵은골재 치환율에 관계없이 1.08~1.29로 기준값을 상회하는 것으로 나타나 순환굵은골재를 사용한 콘크리트 보의 휨 부재설계에 적용 가능할 것으로 판단된다. 따라서 순환굵은골재 활용성 증대를 위해 추가적인 실험을 통하여 순환굵은골재의 구조적 기준정립이 필요할 것으로 판단된다.

In this study, the amount of construction waste created from Demolition and reconstruction of old buildings by environmental contamination by construction waste has been raised as a social problem, according as a means to settle problems the government is being encouraged the use Recycled aggregate. However recycled aggregate has not yet been applied to structures in many cases. Due to uncertain technical verification of long-term durability, the use of recycled aggregate is being limited. Accordingly in this study, High Strength Concrete Beams use Recycled coarse Aggregate to evaluate the performance of the bending and establish national standards for structural design of recycled aggregates aims to provide the basic data.

Reinforced concrete coupled shear wall systems in medium and high-rise construction, where RC beams couple two or more RC walls have been frequently used. The objective of this study is to investigate seismic behavior of coupled shear wall according to the replacement ratio of headed-bar.