In South Korea, the level of Highway Pavement Management System (HPMS) was developed since early 2000. During this time numbers of professional pavement condition monitoring equipment were developed and applied in the actual field. One of the remarkable results is 3D Pavement condition Monitoring profiler vehicle (3DPM) designed and developed in Korea Expressway Corporation Research Division (KECRD). Thanks to this equipment, The surface condition of current pavement can successfully be monitored and proper following management strategy cab be established. However, the inner condition of pavement layer cannot be monitored dur to limitation of 3DPM equipment. In this paper, Bending Beam Rheometer (BBR) mixture creep test was performed to verify the effectiveness of current 3DPM equipment. It was found that the current 3DPM equipment has reasonable feasibility on surveying pavement condition.

최근 국내 겨울철 블랙아이스(Black Ice)로 인해 발생하는 교통사고가 증가하는 추세이며, 한국 도로교통공단 조사 결 과 2016～2020년 겨울철까지 블랙아이스로 인한 사고는 총 4,868건이며, 사상자는 8,938명인 것으로 조사 되었다. 도로상 태에 따라 건조대비 동결상태에서 교통사고 발생시 치사율이 43%로 높게 나타났다. 이러한 사고는 기온이 떨어지는 12 월부터 급증하여, 최저기온이 가장낮은 1월까지 증가한다. 블랙아이스는 도로에 쌓인 눈이 융해(해설)과 동시에 도로 위 각종 이물질과 결합 후 재동결하여 흑색 동결막을 형성하는 것을 말한다. 그 특성상 운전자가 차량내부에서 도로의 상태 를 쉽게 파악할 수 없으며 대부분의 운전자가 차량이 미끄러지기 시작함과 동시에 인지하여 사고가 발생하게 된다. 이에 본 연구에서는 기존 포장체의 미끄럼 저항도를 상태별로 비교 분석하였다. 포장체의 미끄럼 저항성 정도를 파악하기 위 해 영국식 미끄럼저항 시험기 (British Pendulum Tester ; BPT)를 사용하였으며, 포장체의 종류로는 일반적인 밀입도 아스팔트 포장, 배수성 아스팔트 포장, 그루빙(포장 표면에 일정한 규격의 홈을 형성)을 적용한 콘크리트 포장, 그루빙이 없는 콘크리트 포장을 적용하였다. 미끄럼저항 실험은 관련 KS규격 및 ASTM규격에 준하여 실시하되 블랙아이스를 모 사하기위하여 표면온도 영하 2～3℃ 샘플에 강우를 모사한 물을 분사하며 영하 9℃로 10분 동결 후 2mm강수량을 모사 한 수분을 재 분사한 후 시험을 실시하였다.

PURPOSES : The purpose of this study is to provide basic data to improve the service life of asphalt pavement using basalt aggregate in Jeju Island by evaluating the performance of asphalt pavement through analysis of material and structural aspects. METHODS : To evaluate the performance of Jeju Island's asphalt pavement, cracks, permanent deformation, and longitudinal roughness were analyzed for the Aejo-ro road, which has high traffic and frequent premature damage. Cores were collected from Aejo-ro sections in good condition and damaged condition, and the physical properties of each layer were compared and analyzed. In addition, plate cores were collected from two sections with severe damage and the cause of pavement damage was analyzed in detail. RESULTS : About 45% of the collected cores suffered damage such as layer separation and damage to the lower layer. The asphalt content of surface layer in the damaged section was found to be 1.1% lower on average than that in the good condition section, and the mix gradations generally satisfied the standards. The density difference between the cores of each layer was found to be quite large, and the air voids was found to be at a high level. CONCLUSIONS : Test results on the cores showed that, considering the high absorption ratio of basalt aggregate, the asphalt content was generally low, and the high air voids of the pavement was believed to have had a significant impact on damage. High air voids in asphalt pavement can be caused by poor mixture itself, poor construction management, or a combination of the two factors. Additionally, the separation of each layer is believed to be the cause of premature failure of asphalt pavement.

PURPOSES : Derive a road pavement design method using Geocells, aim to derive a road pavement design and construction method suitable for the characteristics of the Bangladesh region METHODS : To assess long-term performance during road construction in Southeast Asia using Geocells, field tests and numerical analysis are conducted to verify stability. RESULTS : A total of 12 displacement measurements were conducted during the field tests, confirming an average load of 15.75 kN and an average displacement of 0.542mm. Inverse analysis was performed to obtain the properties of Geocell combined with compacted soil. The numerical analysis results confirmed that the insertion of Geocell provides better stability compared to the case with only compacted soil. CONCLUSIONS : Based on field tests and numerical analysis, a road design plan suitable for the Southeast Asian environment was proposed. A preliminary test section was selected in the Comilla region of Bangladesh, and test construction has been completed. Subsequent evaluations of the structural performance by soil layer in the test construction area will be conducted to develop a Geocell road pavement method, taking into consideration the characteristics of the Bangladesh region.

PURPOSES : This study is aimed to economic analysis of the ferronickel slag pavement method carried out to suggest the necessity of developing ferronickel slag pavement technology. METHODS : A life cycle cost analysis of the application of the Ferronickel Slag pavement method and the cutting + overlay pavement method was performed to compare the economic indicators and greenhouse gas emissions for each pavement method. RESULTS : As a result of the analysis, regardless of the Ferronickel Slag mixing rate, if the common performance of the Ferronickel Slag pavement method is the same or superior to the existing pavement method, it is more economical than the existing pavement method. Furthermore, the lower the maintenance cost of the Ferronickel Slag pavement method, the higher the economic feasibility due to the high Ferronickel Slag mixing rate. Greenhouse gas emissions can be reduced from at least 9% to up to 53% through the application of the Ferronickel Slag pavement method, except for some scenario analysis results. CONCLUSIONS : This study provided that the Ferronickel Slag pavement method was superior to the existing pavement method in terms of economic and environmental aspects. Therefore, it was found that the objective justification of developing road pavement technology using Ferronickel Slag was secured.

PURPOSES : This study intended to derive a methodology that can evaluate water splash caused by distress on the road surface based on experimental methods and to present quantitatively by analyzing the impact on road users. METHODS : Through literature review, the current problems of road pavement and drainage facility standards, the factors of road splash caused by puddle was selected to measure damage. Field measurements were conducted by setting different conditions for each factors and setting different conditions based on the hypothesis. In addition, water splash by surface distress type and puddle was measured to analyze using statistical techniques from correlation to multi-regression. RESULTS : The maximum and effective distance due to road splash increases as the driving speed, regardless of vehicle load and tyre type. Splash was measured according to the type of road distress to analyze the correlation between the influencing factors, and there was a weak correlation between the width and length of the puddle, depth and the effective distance. In addition, the interaction analysis showed that there was an interaction between the width of the water hole and the depth of puddle. Moreover, based on the multi-regression analysis, it was not statistical significant. This is judged to that the number of data samples used for this analysis is limited because the diversity of puddle conditions cannot be set differently for each type of distress. CONCLUSIONS : Since the distress of depending on the size, depth and shape of the road surface, it is necessary to calculate it and present maintenance standards, so this results present an experimental methodology that can intuitively evaluate damage cased by unestablished puddle. From this results, this is expected to be used as a quantitative indicator to evaluate the satisfaction of road users as a functional performance according to road surface condition.

PURPOSES : The evaluation of the low-temperature performance of an asphalt mixture is crucial for mitigating transverse thermal cracking and preventing traffic accidents on expressways. Engineers in pavement agencies must identify and verify the pavement sections that require urgent management. In early 2000, the research division of the Korea Expressway Corporation developed a three-dimensional (3D) pavement condition monitoring profiler vehicle (3DPM) and an advanced infographic (AIG) highway pavement management system computer program. Owing to these efforts, the management of the entire expressway network has become more precise, effective, and efficient. However, current 3DPM and AIG technologies focus only on the pavement surface and not on the entire pavement layer. Over the years, along with monitoring, further strengthening and verification of the feasibility of current 3DPM and AIG technologies by performing extensive mechanical tests and data analyses have been recommended. METHODS : First, the pavement section that required urgent care was selected using the 3DPM and AIG approaches. Second, asphalt mixture cores were acquired from the specified section, and a low-temperature fracture test, semi- circular bending (SCB) test, was performed. The mechanical parameters, energy-release rate, and fracture toughness were computed and compared. RESULTS : As expected, the asphalt mixture cores acquired from the specified pavement section ( poor condition – bad section) exhibited negative fracture performances compared to the control section (good section). CONCLUSIONS : The current 3DPM and AIG approaches in KEC can successfully evaluate and analyze selected pavement conditions. However, more extensive experimental studies and mathematical analyses are required to further strengthen and upgrade current pavement analysis approaches.

PURPOSES : The objective of this study is to develop the data driven pavement condition index by considering the traffic and climatic characteristics in Incheon city. METHODS : The Incheon pavement condition index (IPCI) was proposed using the weighted sum concept with standardization and coefficient of variation for measured pavement performance data, such as crack rate, rut depth, and International Roughness Index (IRI). A correlation study between the National Highway Pavement Condition Index (NHPCI) and Seoul Pavement Condition Index (SPI) was conducted to validate the accuracy of the IPCI. RESULTS : The equation for determining the IPCI was developed using standardization and the coefficient of variation for the crack rate, rut depth, and IRI collected in the field. It was found from the statistical analysis that the weight factors of the IPCI for the crack rate were twice as high as those for the rut depth and IRI. It was also observed that IPCI had a close correlation with the NHPCI and SPI, albeit with some degree of scattering. This correlation study between the NHPCI and SPI indicates that the existing pavement condition index does not consider the asymmetry of the original measured data. CONCLUSIONS : The proposed pavement condition provides an index value that considers the characteristics of the original raw data measured in the field. The developed pavement condition index is extensively used to determine the timing and method of pavement repair, and to establish pavement maintenance and rehabilitation strategies in Incheon.

PURPOSES : The numeric-based Highway Pavement Management System (HPMS), along with an advanced three-dimensional pavement condition monitoring profiler vehicle (3DPM), in South Korea has presented remarkable advancements in pavement management since the early 2000. Based on these results, visual distress on pavement surfaces can be easily detected and analyzed. Additionally, the entire expressway pavement surface conditions in South Korea can be easily monitored using the current graphical user interface-based advanced information graphic (AIG) approach. Therefore, a critically negative pavement section can be detected and managed more easily and efficiently. However, the actual mechanical performance of the selected pavement layer still needs to be investigated in a more thorough manner not only to provide more accurate pavement performance results but also to verify the feasibility of the current 3DPM and AIG approaches. In this study, the low-temperature performance of the selected asphalt pavement layer section was evaluated to further verify and strengthen the feasibility of the current 3DPM and AIG approaches developed by the Korea Expressway Corporation. METHODS : Based on 3DPM and AIG approach, the positive and negative-riding-quality road sections were selected, respectively. The asphalt material cores were extracted from each section then bending beam rheometer mixture creep test was performed to measure their low-temperature properties. Based on the experimental results, thermal stress results were computed and visually compared. RESULTS : As expected, the asphalt material from the negative driving performance section presented a poorer low-temperature cracking resistance than that from the positive driving performance section. CONCLUSIONS : Current 3DPM equipment can successfully evaluate expressway surface conditions and the corresponding material performance quality. However, more extensive experimental studies are recommended to verify and strengthen the findings of this study