In this paper, the experimental study and finite elements analysis were conducted on homogeneous and dissimilar metals single lap-shear bonded joints to investigate the factor that affect the joint failure load. It was found that factors which have the significant effects on the failure load of the joint was stiffness of the adherends. And from experimental results, it can be confirmed that the failure load increases linearly with overlap length increases. And the failure load of dissimilar metal joints is approximately 1KN(10 ～17%) larger than homogeneous metal joints. In order to confirm this phenomenon, the stress distribution and strain distribution of the specimens were analyzed through the finite element analysis. The difference between homogeneous metals joints and dissimilar metals joints is that stress and strain in adhesive are concentrated at the end of the overlap zone close to aluminium which has lower rigidity than aluminium in case of dissimilar metals joints. From high rigidity of steel, the stress concentration in bonds are decreased and it cause increase of the failure strength at dissimilar metal joints.

Reaction-bonded silicon carbide (RBSC) is a SiC-based composite ceramic fabricated by the infiltration of molten silicon into a skeleton of SiC particles and carbon, in order to manufacture a ceramic body with full density. RBSC has been widely used and studied for many years in the SiC field, because of its relatively low processing temperature for fabrication, easy use in forming components with a near-net shape, and high density, compared with other sintering methods for SiC. A radiant tube is one of the most commonly employed ceramics components when using RBSC materials in industrial fields. In this study, the mechanical strengths of commercial RBSC tubes with different sizes are evaluated using 3-point flexural and C-ring tests. The size scaling law is applied to the obtained mechanical strength values for specimens with different sizes. The discrepancy between the flexural and C-ring strengths is also discussed.

More than sixty percent of highways in Korea were constructed with concrete pavement to carry the heavy traffic loads due to the economic development of this country. The service life of some pavements are close to the end, therefore, they requires the maintenances, rehabilitations and reconstructions to improve their structural performances.According to the similarity of material properties to the concrete pavement, bonded concrete overlay isa good rehabilitation technique used steadily in Korea. However, it is recently reported that the bonded concrete overlays in some highways expose the early distresses and it is assumed that the poor bonding is a cause of this problem. Additionally, the poor bonding of bonded concrete overlay is caused by the bond strength that is less than the bond strength criterion. The pre-investigation of various concrete overlays is conducted in laboratory to determine the possible influence factors reducing the bond strength and it indicates that there are two possible factors affecting the bond strength: the concrete overlay types and the substrate conditions. The study investigates the vulnerable factor between the two factors based on theevaluation of the in-situ bond strength data of bonded concrete overlay gathered from some highways in Korea. The bond strength data is collected from two different application areas: the new constructionand the rehabilitation projects. The new construction and the rehabilitation projects used Latex-modified Concrete (LMC) and Ultra-rapid Hardening Latex-modified concrete (URH-LMC), respectively as the concrete overlay. The evaluation of in-situ bond strength is to determine the percentage of unacceptable bond strength in each projectto study the effect of different types of concrete overlay. Moreover, the percentage of bonding failure modes having the bond strengths less than the criterion is also measured to study the effect of substrate condition.As a result, substrate condition is the vulnerable factor affecting the poor bonding and causing the early distresses in bonded concrete overlay.

PURPOSES : Bonded concrete overlay is a favorable maintenance method since the material properties are similar to existing concrete pavements. In addition, bonded concrete overlay has advantage of structural performance since the overlay layer and the existing pavement perform as a monolithic layer. It is important to have suitable bond strength criteria to secure the performance of bonded concrete overlay. This study aimed to investigate the factors influencing bond strength characteristics between existing concrete pavement and overlay material. METHODS: Bond strength between overlay and existing pavement are measured and analyzed for various conditions such as the type of overlay materials, compressive and flexure strength of overlay and existing pavement, and deterioration status of existing pavement. RESULTS: The strength of overlay material does not significantly influence the bond strength. The overlay of ultra-rapid hardening cement generally gives low bond strength. However, ultra rapid hardening polymer modified concrete gives robust bond strength. The deterioration of existing concrete significantly decrease the bond strength. CONCLUSIONS: Bond strength of bonded concrete overlay highly depends on condition of existing concrete pavement rather than overlay material.

알루미늄 폼을 볼트나 너트를 이용하여 체결한다면 경량성이 감소되므로 접착제로 접합하는 것이 가 장 효율적이다. 이런 알루미늄 폼 접착 구조물에 대한 충격 피로 특성과 접착 합면에 대한 파괴인성 연 구는 매우 부족하며 또한 중요하다. 이에 따라 본 연구에서는 알루미늄 폼으로 만들어진 DCB모델을 접 착제로 접합한 후 두께를 변수로 하여 25mm 부터 45mm까지 10mm차이를 두어 실험과 컴퓨터 시뮬레 이션을 통하여 수행하였다. 실험은 MTS사의 인장 시험기를 사용하여 강제 변위 100mm를 주어 변위에 따른 전단력을 알아보았고, 실험과 똑같은 조건하에 ANSYS를 이용하여 유한요소해석을 수행하였다. 실험과 유한요소해석 값을 비교하여 접착제로 접합된 알루미늄 폼 구조물의 접착 합면에 대한 파괴인성을 고찰하였다.

Joining of AIN ceramics to W and Cu by active-metal brazing method was tried with use of (Ag-Cu)-Ti alloy as insert-metal. Joints were produced under various conditions of temperature, holding time and Ti-content in (Ag-Cu) alloy Reaction and microstructural development in bonded interface were investigated through observation and analysis by SEM/EDS, EPMA and XRD. Joint strengths were measured by shear test. Bonded interface consists of two layers: an insert-metal layer of eutectic Ag- and Cu-rich phases and a reaction layer of TiN. Thickness of reaction layer increases with bonding temperature, holding time and Ti-content of insert-metal. It was confirmed that the growth of reaction layer is a diffusion-controlled process. Activation energy for this process was 260 KJ/mol which is lower than that for N diffusion in TiN. Maximum shear strength of 108 MPa and 72 MPa were obtained for AIN/W and AIN/Cu joints, respectively. Relationship between processing variables, joint strength and thickness of reaction layer was also explained.