본 논문에서는 인장 좌굴 현상을 소개하고 이를 이용한 음의 포아송 효과를 가지는 구조물에 대한 분석을 다룬다. 일반적으로 널리 알려진 좌굴은 압축하중 하에서의 안정성 문제임에 반하여, 인장 좌굴은 인장에 의해 국소적으로 압축력이 생겨 발생하는 좌굴이다. 고전적인 좌굴에 비하여 비교적 최근의 연구이기 때문에 상대적으로 잘 알려지지 않았다. 이에 인장 좌굴 현상을 에너지 관점에서 고 찰하고, 해석을 위하여 비틀림 스프링을 가지는 비선형 트러스 유한요소의 정식화를 수행하였다. 비선형해석을 통해 후좌굴 거동을 분석하고 비틀림 스프링이 주요 인자임을 확인하였다. 이러한 후좌굴 거동은 음의 포아송 비를 가지는 구조물에 적용할 수 있으며, 기 계적 스위치 등의 장치에 적용할 가능성을 보였다. 얻어진 결과들의 정확성 확인을 위하여 해석해와 상용 유한요소해석 결과들과 비 교하여, 개발된 유한요소 모델이 기초 설계에 유용함을 보였다.

Recent studies have revealed that plates stiffened by closed-section ribs can be designed to have greater strength. Thus, this study is about the increasing effect on local plate buckling strength of isotropic plates when longitudinally stiffened with closed-section ribs, which is mainly due to the rotational restraint of the closed-section ribs. The effects on buckling strengths of the stiffened plates are examined by numerical analyses. Three-dimensional finite element models were obtained using a general structural analysis program ABAQUS and a series of eigenvalue analyses were conducted. Through this study, the increasing effect on the local buckling strength due to the rotational stiffness is numerically verified. From the parametric studies, there is an obvious tendency that the local buckling strength of the stiffened plate would converge to the buckling strength of plate with fixed boundary condition. The findings of this study would contribute in improving the optimum design of longitudinally stiffened isotropic plates.

The initial production scale of wind tower is very few. But recently, the production scale of wind tower structure has increased gradually because it maximizes the efficiency in green energy. Many researchers are studying the wind tower, but there is no study about the difference of allowable buckling stress of the wind tower with and without opening. Guideline of codes and standards are very limited when designing a wind tower with an opening. It is also rarely that a study considers the design of the wind tower to be a tubular shell with or without an opening. ABAQUS, a general purpose finite element program, which provides safety evaluation and economical standards for the design and behavior of the wind tower considering the effect of opening was used in the study. Finally, results from this study can serve as reference for structural engineers, manufacturers and further studies of wind turbine when designing a tubular shell wind tower with an opening.

본 논문에서는 탄소성 영역 내 패치 로딩 크기에 따른 알루미늄 합금 사각형 판의 초기 처짐 영향을 수치해석방법으로 이용한 탄성 및 탄소성 대변형 시리즈 해석을 수행하였다. 주변 지지조건은 단순지지로 가정하고 초기 처짐 크기(w/t), 종횡비(a/b), 세장비(b/t)를 고려하여 알루미늄 합금 A6082-T6 사각형 판의 임계 탄성 좌굴하중과 좌굴 후 거동을 검토하였다. 탄성 및 탄소성 대변형 시리즈 해석은 상용프로그램을 사용하였다. 초기 처짐 크기가 작을 경우 하중증가와 함께 면내 강성이 처음부터 감소하며 크기가 커질수록 훨씬 두드러지게 발생한다. 종횡비가 커질수록 초기항복강도는 점차 감소하며 판 두께가 두꺼울수록 패치 로딩 크기(l/b) 0.5 이후 초기 항복강도 감소비율은 얇은 두께보다 더 크게 발생한다.

This study is aimed to examine the influence of the rotational stiffness of U-shaped ribs on the local buckling behaviors of laminated composite plates. Applying the orthotropic plates with eight layers of the layup [(0°)4]s and [(0°/90°)2]s, 3-dimensional finite element models for the U-rib stiffened plates were setup by using ABAQUS and then a series of eigenvalue analyses were conducted. There is a need to develope a simple design equation to establish the rotational stiffness effect, which could be easily quantified by comparing the theoretical critical stress equation for laminated composite plates with elastic restraints based on the Classical laminated plate theory. Through the parametric numerical studies, it is confirmed that there should clearly exist an increasing effect of local plate buckling strength due to the rotational stiffness by closed-section ribs. An applicable coefficient for practical design should be verified and proposed for future study. This study will contribute to the future study for establishing an increasing coefficient for the design strength and optimum design of U-rib stiffened plates.

FRP Sheet와 비좌굴가새를 적용한 보-기둥 접합부의 보강효과를 평가하기 위하여 보-기둥 접합부 실험체에 축력 및 반복 횡가력을 가하여 실험을 수행하였다. 동일한 크기의 6개의 실험체를 제작하였으며 FRP Sheet의 종류 및 비좌굴 가새의 유무를 변수로 하였다. 실험체의 파괴양상 및 최대하중, 연성지수, 에너지소산능력의 측면에서 실험결과를 분석하였다. 실험결과 CFRP Sheet와 비좌굴가새를 혼용한 보강방법이 가장 우수한 성능을 나타냈다.

본 연구의 목적은 일정 축하중과 반복횡하중 하에서 탄소섬유시트와 비좌굴 가새로 보강된 보-기둥 시험체의 횡방향 거동 평가를 통하여 사용된 보강 방법의 구조적 성능을 검증하는 것이다. 세 개의 시험체를 비보강, 탄소섬유보강, 탄소섬유와 비좌굴 가새 보강 방법을 각각 적용하여 제작하였다. 변위에 따른 최대, 최소하중은 하중-변위 관계를 분석함으로써 평가되어지며, 하중과 강성의 관계는 비교구간의 유효강성 분석에 의해 평가된다. 실험의 수행 결과, 보강을 하지 않은 시험체에 비하여 보강을 적용한 시험체는 최대허용하중과 유효강성, 철근 항복 시 재하 횡하중, 변위연성비 등에서 상대적으로 우수한 성능을 보였다.

본 논문의 목적은 전단하중을 받는 얇은 원통구조물의 세장비에 따른 좌굴특성을 보다 깊이 있게 검토하는 것이다. 이를 위하여 J. Okada 등이 제안한 좌굴평가식을 사용하여 세장비에 따른 좌굴강도 평가를 수행하였다. 좌굴강도 평가 결과들로부터 세장비 L/R=3.1, 1.6, 그리고 1.0을 갖는 세가지 좌굴시험체를 결정하고 이에 대한 수치해석과 좌굴특성시험을 수행하였다. 그 결과, 세장비 L/R=3 이상인 경우 평가식에서 예측된 바와 같은 굽힘좌굴이 지배적으로 나타났으며 세장비 L/R=1.0이하로 작을 경우에는 전단좌굴이 지배적으로 나타났고, 세장비 L/R=1.6 영역에서는 전단과 굽힘좌굴이 동시에 발생하는 복합자굴 특성이 나타났다 그리고 수치해석과 평가식에 의한 좌굴특성평가 결과는 시험결과들과 잘 일치하였다.

Two way grid single-layer domes are of great advantage in fabrication and construction because of the simple fact that they have only four members at each junction. But, from a point of view of mechanics, the rectangular latticed pattern gives rise to a nonuniform rigidity-distribution in the circumferential direction. If the equivalent rigidity is considered in the axial direction of members, the in-plane equivalent shearing rigidity depends only on the in-plane bending rigidity of members and its value is very small in comparison to that of the in-plane equivalent stretching rigidity. It has a tendency to decrease buckling -strength of dome considerably by external force. But it is possible to increase buckling strength by the use of roofing covering materials connected to framework. In a case like this, shearing rigidity of roofing material increases buckling strength of the overall structure and can be designed economically from the viewpoint of practice. Therefore, the purpose of this paper, in Lamella dome and rectangular latticed dome that are a set of 2-way grid dome, is to clarify the effects of roofing covering materials for increasing of buckling strength of overall dome. Analysis method is based on FEM dealing with the geometrically nonlinear deflection problems. The conclusion were given as follows: 1. In case of Lamella domes which have nearly equal rigidity in the direction of circumference, the rigidity of roofing covering materials does not have a great influence on buckling-strength, but in rectangular latticed domes that has a clear periodicity of rigidity, the value of its buckling strength has a tendency to increase considerably with increasing rigidity of roofing covering materials 2. In case of rectangular latticed domes, as rise-span-ratio increases, models which is subjected to pressure -type-uniform loading than vertical-type-uniform loading are higher in the aspects of the increasing rate of buckling- strength according to the rate of shear reinforcement rigidity, but in case of Lamella dome, the condition of loading and rise-span-ratio do not have a great influence on the increasing rate of buckling strength according to the rate of shear reinforcement rigidity.

In Single-layer latticed domes with rectangular network which is composed of ring of circumferential direction and rafter of longitudinal direction, that is, rib domes, if we use the cross-membered junction's method for the advantage in fabrication and construction, the eccentricity is occurred in the nodal point of crossing members. This paper is aimed at investigating the buckling characteristics for the effect of eccentricity according to rise-span ratios and distance of eccentricity. Analysis method is based on FEM dealing with the geometrically nonlinear deflection problems. The conclusion were given as follows: 1. The maximum decreasing ratio of buckling strength due to the junction's eccentricity is about 60% in models of this paper. 2. In the increasing ratio of buckling strength for rise-span ratio, that of Type 3 models is larger than that of type 2 models. On the other hand, that of Type 2 mode is larger than that of Type 3 for eccentricity-distance. 3. In the viewpoint of the value of buckling strength, that of Type 2 models is larger than that of type 3 models. The effect of the junction's rigidity on buckling strength is not great for overall models. Therefore if we use the cross-membered junction's method for the advantage in fabrication and construction, the method of Type 2 will have the great advantage of that of Type 3.

This parametric study investigates the effect of significant parameters on the elastic global lateral torsional buckling capacity of horizontally curved twin I-girder systems. Included are the effect of curvature and the effect of girder spacing. Twin I-girder systems analyzed in this study are those which are interconnected by intermediate cross frames and are subjected to uniform moment. The finite element analysis software, ABAQUS, is used to model the horizontally curved twin I-girder system and conduct the buckling analysis. To see the significant effect of curvature and girder spacing, the results from the finite element analysis of horizontally curved twin I-girder systems are compared to the results of a closed form solution for straight twin I-girder systems. The findings of this parametric study will be shown using illustrative figures and tabulated data and conclusions are made.