검색결과

검색조건
좁혀보기
검색필터
결과 내 재검색

간행물

    분야

      발행연도

      -

        검색결과 14

        2.
        2023.05 구독 인증기관·개인회원 무료
        The soils contaminated with radionuclides such as Cs-137 and Sr-90 should be solidified using a binder matrix, because radioactively contaminated soils pose environmental concerns and human health problems. Ordinary Portland cement has been widely used to solidify various radioactive wastes due to its low cost and simple process. In this study, simulant soil waste was solidified using cement waste form. The soils were collected around ‘Kori Nuclear Power Plant Unit 1’ and they were contaminated with the prepared simulant liquid waste containing Fe, Cr, Cs, Ni, Co, and Mn. The water-to-dry ingredients (W/D) ratio of cement waste form was 0.40. The cement paste was poured into a cubic mold (5×5×5 cm) and then cured for 28 days at room temperature. The 28-day compressive strength, water immersion, and EPA1311-toxicity characteristic leaching procedure (TCLP) tests were performed to evaluate the structural stability of cement waste form. The compressive strength was not proportional to soil waste loading, and the lowest compressive strength (4±0.1 MPa) was achieved in cement waste form containing 50wt% soil waste. After the water immersion test for 90 days, the compressive strength of cement waste form with 50wt% soil waste increased to 7.5±0.6 MPa, meeting the waste form acceptance criteria in the repository. It is believed that long-term water immersion test contributed to the additional curing and hydration reaction, resulting in the enhanced compressive strength. As a result of the TCLP test, the released amount of As, Ba, Cd, Cr, Pb, Se, Co, Cs, and Sr was less than the domestic and international standards. These results imply that cement waste form can be a promising candidate for the solidification of radioactive soil wastes.
        3.
        2022.10 구독 인증기관·개인회원 무료
        The number of nuclear power plants that are permanently shut down or decommissioned is increasing worldwide, and accordingly, research is being conducted on an appropriate method for disposing of radioactive waste generated during the decommissioning of nuclear power plants. In the case of waste liquid generated during the decommissioning of nuclear power plants, it is important not only to efficiently reduce waste but also to secure the suitability of disposal. One of the solidification treatment methods for radioactive waste is cement solidification, but since cement solidification has poor solidification properties and generates a large amount of waste, improvement activities have been pursued. This study aims to develop high-performance cement-based materials and solidification treatment technology for solidification of liquid radioactive waste generated during nuclear decommissioning in order to improve the problems of cement solidification treatment method. For the development of polymer cement, epoxy resin and polyamine/amide mixed type and general Portland cement were mixed in various ratios. The most appropriate mixing ratio was 4.5:2, which showed the highest compressive strength. A simulated waste liquid was prepared by referring to the preliminary decommissioning plan of Shin-Kori Units 5 and 6, and it was dried and made into granules. Polymer cement was injected into a drum filled with granules by vacuum pressure to prepare a waste form matrix. In the solidification process, granules made by drying the waste liquid were used, and the solidification agent was filled in between the granules, so the total volume of solid radwaste was reduced compared to the conventional cement solidification treatment method. As a result, the amount of waste decreased to about 1/3, and the volume reduction rate increased by about 2.2 times. The compressive strength of 3,243 psi was confirmed in the disposability performance test for the manufactured solid samples. The compressive strength after the thermal cycling test, irradiation test, microorganism test, and immersion test was 2,257 psi, 2,306 psi, 4,530 psi, and 2,263 psi, respectively, exceeding the acceptance criteria of 500 psi. The leaching index was 7~13, and no free standing water was generated.
        4.
        2022.05 구독 인증기관·개인회원 무료
        Magnesium potassium phosphate cements (MKPCs) are prepared by the acid-base reaction of dead burned magnesia (MgO) and monopotassium phosphate (KH2PO4). Low-pH cementitious materials such as MKPCs are currently of interest for the geological disposal of nuclear waste. MKPCs have advantages such as high early strength, high bonding strength, small drying shrinkage, low permeability, and high sulfate resistance. According to the results of previous studies, it is known that cesium, strontium, and cobalt are immobilized in the form of MgCsxK1−xPO4·6H2O, MgxSr1−xKPO4·6H2O, and Co3(PO4)2, respectively, in MKPCs. However, these results were predicted based on thermodynamic data, not directly observed precipitates to clearly show the evidence. Therefore, in this study, we directly analyzed the immobilized forms of Cs, Sr, and Co, respectively. CsNO3, Sr(NO3)2, and Co(NO3)2·6H2O powders (0.3 mol each) were mixed individually in each of the MKPC suspensions. The suspensions in which KH2PO4 was dissolved were pH 4.3 and the dissolution of MgO decreased the H+ concentration, raising the pH close to 11. The hydration products according to pH evolution in the MKPC suspensions were analyzed, and the change in the concentration of ions in the aqueous solution was also measured. An aqueous solution was obtained using a syringe filter (0.45 μm) to analyze the ion concentrations in the solution of the suspension. The collected solutions were diluted with nitric acid and analyzed using inductively coupled plasma mass spectrometry. To characterize the solid phases, the suspensions were obtained with a pipette at specific times and filtered under a vacuum in a Buchner funnel. Because the amounts of hydration products including Cs, Sr, and Co were small, it was not observed by XRD and TGA analysis, but their components could be analyzed by SEM-EDS. The final precipitate forms of Cs, Sr, and Co in the MKPC matrix are MgCsPO4·6H2O, SrHPO4, and Co3(PO4)2·8H2O, respectively.
        7.
        2020.12 KCI 등재 SCOPUS 구독 인증기관 무료, 개인회원 유료
        Two waste forms, namely cement and geopolymer, were investigated and tested in this study to solidify the corrosive sludge generated from the surface and precipitates of the tubes of steam generators in nuclear power plants. The compressive strength of the cement waste form cured for 28 days was inversely proportional to waste loading (24.4 MPa for 0wt% to 2.7 MPa for 60wt%). The corrosive sludge absorbed the free water in the hydration reaction to decrease the cementation reaction. When the corrosive sludge waste loading increased to 60wt%, the cement waste form showed decreased compressive strength (2.7 MPa), which did not satisfy the acceptance criteria of the repository (3.45 MPa). Meanwhile, the compressive strength of the geopolymer waste form cured for 7 days was proportional to waste loading (23.6 MPa for 0wt% to 31.9 MPa for 40wt%). The corrosive sludge absorbed the free water in the geopolymer when the water content decreased, such that a compact geopolymer structure could be obtained. Consequently, the geopolymer waste forms generally showed higher compressive strengths than cement waste forms.
        4,800원
        9.
        2018.06 KCI 등재 SCOPUS 구독 인증기관 무료, 개인회원 유료
        Currently, the Korea Atomic Energy Research Institute (KAERI) is planning to build the Ki-Jang Research Reactor (KJRR) in Ki-Jang, Busan. It is important to safely dispose of low-level radioactive waste from the operation of the reactor. The most efficient way to treat radioactive waste is cement solidification. For a radioactive waste disposal facility, cement solidification is performed based on specific waste acceptance criteria such as compressive strength, free-standing water, immersion and leaching tests. Above all, the leaching test is important to final disposal. The leakage of radioactive waste such as 137Cs causes not only regional problems but also serious global ones. The cement solidification method is simple, and cheaper than other solidification methods, but has a lower leaching resistance. Thus, this study was focused on the development of cement solidification for an enhancement of cesium leaching resistance. We used Zeolite and Loess to improve the cesium leaching resistance of KJRR cement solidification containing simulated KJRR liquid waste. Based on an SEM-EDS spectrum analysis, we confirmed that Zeolite and Loess successfully isolated KJRR cement solidification. A leaching test was carried out according to the ANS 16.1 test method. The ANS 16.1 test is performed to analyze cesium ion concentration in leachate of KJRR cement for 90 days. Thus, a leaching test was carried out using simulated KJRR liquid waste containing 3000 mg·L-1 of cesium for 90 days. KJRR cement solidification with Zeolite and Loess led to cesium leaching resistance values that were 27.90% and 21.08% higher than the control values. In addition, in several tests such as free-standing water, compressive strength, immersion, and leaching tests, all KJRR cement solidification met the waste acceptance or satisfied the waste acceptance criteria for final disposal.
        4,200원
        10.
        2018.03 KCI 등재 SCOPUS 구독 인증기관 무료, 개인회원 유료
        우라늄 토양 및 콘크리트 폐기물의 동전기 제염 후 방사성폐기물의 시멘트 고화특성을 분석하기 위하여, 시멘트 고화 유동성 시험을 수행하고 시멘트 고화 시료를 제작하였다. 시멘트 고화시료에 대하여 압축강도, pH, 전기전도도, 방사선조사 효과 및 부피증가를 분석하였다. 방사성폐기물의 시멘트 고화의 작업 적정도는 175~190% 정도였다. 시멘트 고화시료의 방사선 조사 후 압축강도는 방사선 조사 전 압축강도 보다 약 15% 감소하였으나, 한국원자력환경공단 인수기준 (34 kgf·cm-2)을 만족하였다. 동전기 제염 후 방사성폐기물의 시멘트 고화 시료에 대한 SEM-EDS 분석결과, 알루미늄상은 시멘트와 잘 결합 한 형상을 나타낸 반면, 칼슘상은 시멘트와 분리된 형상을 나타내었다. 방사성폐기물의 시멘트 고화 부피는 시멘트에 대한 폐기물의 배합과 수분량에 따라 다르게 나타났다. 방사성폐기물의 시멘트 고화 부피(C-2.0-60)는 약 30% 증가였으며 동전기 제염 후 생성된 방사성폐기물의 영구처분은 적절하다고 판단되었다.
        4,000원
        14.
        2017.01 KCI 등재 서비스 종료(열람 제한)
        About 4,800 soil drums were generated in the process of maintenance on KRR site (Korea Research Reactor) in Seoul. Most of the drums are processed by regulatory clearance in 2007-2008 and the remaining 1800 drums are currently stored in KAERI (Korea Atomic Energy Research Institute). To decide a treatment method of radioactive soil for final disposal, the soil is classified according to a particle size. Based on the results of the radioactivity concentration for the classified soil, methods such as regulatory clearance, decommissioning, and solidification were decided. Many papers show that radioactive soil is disposed of using a decontamination agent or other method. But it is difficult to decontaminate radioactive particles from fine soil particles because the adsorptive power of fine soil particles is too strong. This study was focused on finding a particle size distribution of radioactive soil that can be used as an operating range for cement solidification produced by a suitable ratio of radioactive soil for final disposal. Workability, free-standing water, compressive strength, immersion, and leaching tests were carried out to evaluate characteristics of the cement solidification. Cement solidification is the only method for final disposal because radioactive soil particle sizes below 500 μm exceed the regulatory clearance criteria (< 0.1 Bq/g). According to the test results for cement solidification, 0.4 water/cement and 0.5 soil/cement ratios are the most appropriate operating ranges.