According to the automobile industry has been developing day by day, traffic accidents are increasing and the rear-end collision is the second largest of the entire collision. Due to the high social cost caused by rear-end collision, several studies are in progress at home and abroad. Previous studies have shown that neck injury caused by rear-end collisions can be prevented by seat conditions. In this study, to find the condition that reduces neck injury, change of neck injury in rear-end collision is analyzed according to headrest height, seatback angle, and seatback torque using BioRID II dummy model and passenger behavior analysis program MADYMO. Therefore, it is expected that the condition of each variable to reduce the risk of injury to the neck can be applied to the seat design, which will reduce the injury and the social cost caused by the rear-end collision.

Bulk nanostructured copper was fabricated by a shock compaction method using the planar shock wavegenerated by a single gas gun system. Nano sized powders, average diameter of 100 nm, were compacted into the cap-sule and target die, which were designed to eliminate the effect of undesired shock wave, and then impacted with analuminum alloy target at 400 m/s. Microstructure and mechanical properties of the shock compact specimen were ana-lyzed using an optical microscope (OM), scanning electron microscope (SEM), and micro indentation. Hardness resultsshowed low values (approximately 45~80 Hv) similar or slightly higher than those of conventional coarse grained com-mercial purity copper. This result indicates the poor quality of bonding between particles. Images from OM and SEMalso confirmed that no strong bonding was achieved between them due to the insufficient energy and surface oxygenlayer of the powders.

During the last 10 years, the various type of high speed craft have been greatly developed, and since around of 1990 the large size of high speed passenger and/or cargo vessels are also introduced and took into the service in the various routes over the world. In a marine traffic way some bridge need to build across a rivers, cannals or a waterways. This one will be an obstruction and potential risk of collision in the way of high speed craft. Accordingly some of collision accident have been reported, which were caused by a lost control, wind and hydrodynamic forces, fog or human errors. In this paper a high speed craft having 40 m length is assumed to be collided with a circular type of bridge piers at right angle. The mode of deformation, penetration depth of collapse, impact forces, reduction of speed, loss of kinetic energy, and influence of scantlings, etc. have been calculated in each speed with a time variation to find a maximum values within a limit, and are graphically presented.

본 논문에서는 선박충돌사고의 주요한 원인이 되는 인적운항과실의 감소 및 효과적인 선박충돌회피를 지원하기 위해 새로이 제안된 '속력을 고려한 선박충돌회피지원 모델'을 기반으로 한 선박충돌회피지원 프로그램 개발에 관하여 연구하였다. 이 프로그램은 선행 연구에서 고려되지 않은 상대선박의 속력이 고려되었으며, 자선의 선회특성을 이용하여 상대선박의 침로, 속도에 대한 충돌회피 가능영역과 방법을 표시함으로써, 근접상황에서도 효과적인 충돌회피 조종을 지원할 것이다.

선박의 충돌회피 방법을 제시하는 관점에 있어, 두 선박의 조우각도에 따라 속력이 충분히 고려되어야 할 것이다. 하지만 선박의 충돌회피를 위해 새롭게 연구된 근접상황 선박충돌회피지원 모델의 안전경계영역(Safe-Guard Ring) 설정은 본선과 상대선박의 속력비가 약 1.7이하로 제한되어 있으므로 제한된 범위 이외의 경우에서 충돌 위험이 존재 할 수 있다. 따라서 본 연구에서는 두 선박이 조우하는 각도 및 속력을 고려한 안전경계영역 설정을 연구함으로써 안전한 충돌회피 조종을 위한 선박충돌회피모델을 제시하고자 한다.