The nanostructured dysprosium oxide ( Dy2O3) was synthesized by the co-precipitation method and incorporated with graphitic carbon nitride (g-C3N4) using the ultrasonication method. The resultant product is denoted as Dy2O3/ g-C3N4 nanocomposite which was further used for electrochemical sensing of riboflavin (RF). The physicochemical properties of Dy2O3/ g-C3N4 nanocomposite were examined using several characterization techniques. The obtained results exhibit the nanocomposite formation with the preferred elemental compositions, functional groups, crystalline phase and desired surface morphology. The electrocatalytic performance of Dy2O3/ g-C3N4 nanocomposite was scrutinized with a glassy carbon electrode (GCE) via differential pulse voltammetry (DPV) and cyclic voltammetry (CV) techniques with the conventional three-electrode system. The modified electrode distributes more active surface area suggesting high electrocatalytic activity for the RF detection with two linear ranges (0.001–40 μM and 40–150 μM), a low detection limit of 48 nM and sound sensitivity (2.5261 μA μM−1 cm− 2). Further, the designed sensor possesses high selectivity, excellent stability, repeatability and reproducibility. Finally, the fabricated sensor was successfully estimated for the detection of RF in actual food sample analysis using honey and milk with better recovery.

Graphitic carbon nitride (g-C3N4) has attracted extensive attention in energy storage due to its suitable and tunable bandgap, high chemical/thermal stability, earth abundance and environmental friendliness. However, its conductivity should be improved to work as the electrode materials in supercapacitors. In this report, we have prepared a two-dimensional composite (CN-PANI) based on g-C3N4 and polyaniline (PANI) by in-situ polymerization, which can be efficiently applied as electrode material for supercapacitors. The introduction of PANI can increase the conductivity of the electrode, and the porous structure of g-C3N4 can provide enough channels for the transport of electrolyte ions and improve the electrode stability. As a result, the obtained CN-PANI demonstrates excellent specific capacitance (234.0 F g− 1 at 5 mV/s), good rate performance and high cycling stability (86.2% after 10,000 cycles at 50 mV/s), showing great potential for high-rate supercapacitors.

To solve the problem of water pollution, researchers have proposed a photocatalytic degradation technology, in which the key factor is the development of efficient photocatalytic materials. Graphitic carbon nitride (g-C3N4), an n-type semiconductor, has been widely studied due to its suitable band gap (2.7 eV), low cost, easy preparation, non-toxicity, and high photostability. However, the pure-phase g-C3N4 still has defects such as low specific surface area, insufficient visible light absorption, low charge mobility, few active sites for interfacial reaction, and easy recombination of photogenerated electron–hole pairs, which leads to the lower photocatalytic activity of g-C3N4. Aiming at the problems mentioned above, this paper focus on the synthesis of g-C3N4-based composites with high photocatalytic activity via lemon juice induction method. Thiourea and lemon juice were selected as precursors, and carbon quantum dots (CQDs) as electron mediators were introduced anchoring on the surface of g-C3N4 to build g-C3N4/CQDs with compact interface. The results showed that small-sized CQDs are uniformly distributed on the surface of g-C3N4, and the g-C3N4/CQDs composite has a 2D0D structure, which reduces the recombination of photogenerated electron–hole pairs. The photocatalytic degradation efficiency of 4% g-C3N4/CQDs for RhB reaches the highest data of 90.9%, and the photocatalytic degradation rate is 0.016 min− 1, which is about 2.3 times that of g-C3N4. After four cycles of photocatalytic reaction, the photocatalytic degradation efficiency of the material remained at 81.7%. Therefore, the g-C3N4/CQDs synthesized via lemon juice induction has a more stable microstructure, and the charge separation efficiency is greatly improved, which is suitable for practical photocatalytic environmental protection.

Graphitic carbon nitride ( C3N4) has been intensively studied in the last 25 years. Although the number of papers about C3N4 published per year has been growing exponentially, there are still some unclear issues with this material. One of them is s-triazine C3N4 (s-C3N4), which is an allotrope of C3N4. The theoretical computational as well as experimental synthetic results are not unambiguous. The properties of s-C3N4 have been described only in two papers, and no similar and reproducible results have been obtained so far. This paper provides a brief overview of s-C3N4 to bring attention to this material, for example, as a potential photocatalyst.

In the present study, a novel electrochemical sensor for acetaminophen (AMP) which included quantum graphitic carbon nitride dots, g-C3N4QDs, was designed and conducted with molecular imprinted polymer (MIP). First, bulk g-C3N4 was generated with direct thermal polycondensation of melamine. After the treatment of the acidic solution containing H2SO4: HNO3 (1:1, v:v), the heating treatment at 200 °C on the dispersion provided g-C3N4QDs. In this respect, for nanomaterial characterization, some spectroscopic approaches were performed including Fourier-transform infrared spectroscopy (FTIR), and X-ray photoelectron spectroscopy (XPS) as well as electroanalytical methods such as electrochemical impedance (EIS) and cyclic voltammetry (CV). In accordance with the aims of the study, AMP imprinted electrode was formed after high electrocatalytic performance and linear range of 1.0 × 10– 11–2.0 × 10– 8 M and the LODs of 2.0 × 10– 12 was achieved. Eventually, an AMP-printed sensor was also used for AMP identification in pharmaceutical samples.