Interim dry cask storage systems comprising AISI 304 or 316 stainless steel canisters have become critical for the storage of spent nuclear fuel from light water reactors in the Republic of Korea. However, the combination of microstructural sensitization, residual tensile stress, and corrosive environments can induce chloride-induced stress corrosion cracking (CISCC) for stainless steel canisters. Suppressing one or more of these three variables can effectively mitigate CISCC initiation or propagation. Surface-modification technologies, such as surface peening and burnishing, focus on relieving residual tensile stress by introducing compressive stress to near-surface regions of materials. Overlay coating methods such as cold spray can serve as a barrier between the environment and the canister, while also inducing compressive stress similar to surface peening. This approach can both mitigate CISCC initiation and facilitate CISCC repair. Surface-painting methods can also be used to isolate materials from external corrosive environments. However, environmental variables, such as relative humidity, composition of surface deposits, and pH can affect the CISCC behavior. Therefore, in addition to research on surface modification and coating technologies, site-specific environmental investigations of various nuclear power plants are required.

CO2 photocatalytic reduction is a carbon–neutral renewable energy technology. However, this technology is restricted by the low utilization of photocatalytic electrons. Therefore, to improve the separation efficiency of photogenerated carriers and enhance the performance of CO2 photocatalytic reduction. In this paper, g-C3N4/Pd composite with Schottky junction was synthesized by using g-C3N4, a two-dimensional material with unique interfacial effect, as the substrate material in combination with the co-catalyst Pd. The composite of Pd and g-C3N4 was tested to have a strong localized surface plasmon resonance effect (LSPR), which decreased the reaction barriers and improved the electron utilization. The combination of reduced graphene oxide (rGO) created a π–π conjugation effect at the g-C3N4 interface, which shortened the electron migration path and further improved the thermal electron transfer and utilization efficiency. The results show that the g-C3N4/ rGO/Pd (CRP) exhibits the best performance for photocatalytic reduction of CO2, with the yields of 13.57 μmol g− 1 and 2.73 μmol g− 1 for CO and CH4, respectively. Using the in situ infrared test to elucidate the intermediates and the mechanism of g-C3N4/rGO/Pd (CRP) photocatalytic CO2 reduction. This paper provides a new insight into the interface design of photocatalytic materials and the application of co-catalysts.

Safe management of spent nuclear fuel (SNF) is a key issue to determine sustainability of current light water reactor (LWR) fleet. However, none of the countries are actually conducting permanent disposal of SNFs yet. Instead, most countries are pursuing interim storage of spent nuclear fuels in dry cask storage system (DCSS). These dry casks are usually made of stainlesssteels for resistibility against cracking and corrosion, which can be occurred over a long-term storage period. Nevertheless, some corrosion called Chloride-Induced Stress Corrosion Cracking (CISCC) can arise in certain conditions, exacerbating the lifetime of dry casks. CISCC can occur if the three conditions are satisfied simultaneously: (i) residual tensile stress, (ii) material sensitization, and (iii) chloride-rich environment. A residual tensile stress is developed by the two processes. One is the bending process of stainless-steel plates into a cylindrical shape, and the other is the welding process, which can incur solidification-induced stress. These stresses provide a driving force of pit-to-crack transition. Around the fusion weld areas, chromium is precipitated at the grain boundary as a carbide form while it depletes chromium around it, leading to material susceptible to pitting corrosion. It is called sensitization. Finally, coastal regions, where nuclear power plants usually operate, tend to have a higher relative humidity and more chloride concentration compared to inland areas. This high humidity and chloride ion concentration initiate pitting corrosion on the surface of stainless-steels. To prevent initiation of CISCC, at least one of the three conditions should be removed. For this, several surface engineering techniques are under investigation. One of the most promising approaches is surface peening method, which is the process that impacts the surface of materials with media (e.g., small pins, balls, laser pulse). By this impact, plastic deformation on the surface occurs with compressive stress that counteracts with pre-existing residual tensile stress, so this approach can prevent pit-to-crack transition of stainless-steels. Also, cold spray deposition can prevent CISCC. Cold spray deposition is a method of spraying fine metal powder to a substrate by accelerating them to supersonic velocity with propellant gas. As a result, a thin coating composed of the feedstock powders can protect the substrate from outer corrosive environments. In addition, the impact of the feedstock powder on the substrate during the process provides compressive stress, similar to the peening method.

The disposing method of the low-intermediate-level radioactive waste, near-surface disposal facilities are generally used. This disposal method refers to a method of constructing a concrete structure on the surface of the ground, putting radioactive waste in it, and covering it with an engineered barrier to isolate human life. Among these, engineered barriers mean covering multiple layers of heterogeneous materials such as sand, clay, and gravel. Engineering barriers have the purpose of delaying the release of radioactive materials into the natural environment as much as possible, and maintaining the isolation of radioactive waste and human life for as long as possible. In this study, the design and construction method of the facility to demonstrate the performance of the engineered barrier that isolates the surface disposal facility from nature was described. In addition, the design and construction method of monitoring technology that can monitor the safety of engineered barriers by measuring information such as moisture, temperature, and slope safety in real time was also explained.

In this paper, the performance evaluation of Al-graphene nanoplatelets (GNP) composites surface engineered by a modified friction stir processing (FSP) is reported. Here, multiple micro channels (MCRF) are used to incorporate GNPs in the aluminium matrix instead of a single large groove (SCRF) that is usually used in conventional FSP. With the MCRF approach, ~ 18% higher peak temperature (compared to SCRF) was observed owing to the presence of aluminium sandwiched between consecutive microgrooves and higher heat accumulation in the stir zone. The MCRF approach have significantly reduced the coefficient of friction and wear rates of the processed composites by ~ 14% and ~ 57%, respectively as compared to the SCRF approach. The proposed reinforcement filling method significantly improves the particle dispersion in the matrix, which in turn changes the adhesion mode of wear in SCRF to abrasive mode in MCRF fabricated composites. The uniformly squeezed out GNP tribolayer prevented the direct metal to metal contact between composite and its counterpart which have effectively reduced the deterioration rates.

In reverse engineering area, it is rapidly developing reconstruction of surfaces from scanning or digitizing data, but geometric models of existing objects unavailable many industries. This paper describes new methodology of reverse engineering area, good strategies and important algorithms in reverse engineering area. Furthermore, proposing reconstruction of surface technique is presented. A method find base geometry and blending surface between them. Each based geometry is divided by triangular patch which are compared their normal vector for face grouping. Each group is categorized analytical surface such as a part of the cylinder, the sphere, the cone, and the plane that mean each based geometry surface. And then, each based geometry surface is implemented infinitive surface. Infinitive average surface's intersections are trimmed boundary representation model reconstruction. This method has several benefits such as the time efficiency and automatic functional modeling system in reverse engineering. Especially, it can be applied 3D scanner and 3D copier.