V-type coupling, which is often applied to wastegate-turbochargers(WGT), is a mechanical fastener. Its radial forces generated from the bolt pretension load colse contact with each other to the axial direction for turbine housing and center housing rotating assembly(CHRA). In addition, the torsional stiffness between two bodies should be sufficiently secured to minimize the linkage angle change from the EWGA to the valve spindle. Therefore, in this study, the torsional stiffnesses according to the effects of positioning pins and friction coefficient, and the bolt pretension loads were calculated for V-coupling turbocharger. As a result, it can be seen that the torsional stiffness of the coupling according to the number of position pins is very small. And, when the friction coefficient and the axial force of the bolt are large, the torsional stiffness is greatly increased, and gradually decreasing when the bolt load of the coupling is about 6,000 N or more.
In the case of a school building, even though it is a regular structure in terms of plan shape, if the masonry infill wall acts as a lateral load resisting element, it can be determined as a torsionally irregular building. As a result, the strength and ductility of the structure are reduced, which may cause additional earthquake damage to the structure. Therefore, in this study, a structure similar to a school building with torsional irregularity was selected as an example structure and the damping performance of the PC-BRB was analyzed by adjusting the eccentricity according to the amount of masonry infilled wall. As a result of nonlinear dynamic analysis after seismic reinforcement, the torsional irregularity of each floor was reduced compared to before reinforcement, and the beams and column members of the collapse level satisfied the performance level due to the reduction of shear force and the reinforcement of stiffness. The energy dissipation of PC-BRB was similar in the REC-10 ~ REC-20 analytical models with an eccentricity of 20% or less. REC-25 with an eccentricity of 25% was the largest, and it is judged that it is effective to combine and apply PC-BRB when it has an eccentricity of 25% or more to control the torsional behavior.
The stiffness of a bicycle frame is a major factor of a bicycle performance related to safety, stability, and weight. In this study, the torsional and bottom bracket stiffness of a bicycle frame were experimentally investigated. The torsional and bottom bracket stiffness for 63 bicycle frames were evaluated and analyzed by measuring the displacement of frames. The torsional stiffness is related with turning performance and the bottom bracket stiffness is related with power transmission. The experimental results show that the average stiffness varies up to 20 % according to the frame materials and types. The torsional stiffness has a strong corelation with the bottom bracket stiffness even though they have different effects on a bicycle frame. It seems that the experimental results can be applied to the quality criteria of racing bicycles and also design standard of a bicycle frame.
본 저자의 이전연구(김문영 등, 2004)에서는 2차원 차량 모형과 전단변형 및 회전관성 효과가 고려된 현수교요소와의 상호작용을 고려한 2차원 수직응답에 대한 동적해석을 수행하였다. 본 연구에서는 전단변형 효과와 편심차량의 효과를 알아보는데 목적을 두었다. 이를 위하여 전단변형 및 회전관성 효과가 고려된 3차원 현수교의 수직, 비틂에 대한 고유진동수와 모드형상, 그리고 교량-차량 에너지로부터 라그랑지안식을 이용하여 상호작용을 고려할 수 있는 3차원 운동방정식을 유도한다. 이후 모드중칩법을 이용하여 유도된 운동방정식을 Newmark method를 사용하여 동적해석을 수행한다. 마지막으로 본 연구에서 제시한 이론을 따라 수치해석예제를 수행하여 차량의 동적거동을 분석한다.
After studying the composition about the torsional shafting of main engine for fishing vessel with Power Take Off (PTO) System, the authors made a computer program using the transfer stiffness coefficient method (TSCM) for analyzing torsional vibration about the shafting with PTO system and nonlinear elastic coupling. The torsional shafting of main engine was separated by 3 types according to the connecting. The torsional shafting of main engine was separated by 3 types according to the connecting condition of main engine with propeller or the PTO system or both of them. In this paper, the change of natural frequencies and natural modes according to connecting condition of torsional shafting and nonlinear elastic coupling were analyzed. The accuracy of the TSCM was confirmed by comparing with the computational results of the Finite Element Method.
본 논문에서는 횡비틀림좌굴을 고려하는 2차 소성힌지해석법을 이용하여 3차원 강뼈대구조물의 설계기법을 개발하였다. 본 해석은 구조시스템 및 개별부재의 재료적 기하학적 비선형 거동을 고려한다. 더욱이, 종래의 2차 소성힌지해석에서 횡비틀림좌굴효과에 의한 휨강도 감소효과를 고려하지 못한 문제를 해결하였다. 강뼈대구조물의 잔류응력과 휨에 의한 비선형성 및 기하학적 불완전성에 의한 점진적인 소성화효과를 고려하는 효율적인 방법을 기술하였다. 횡비틀림좌굴효과를 고려하기 위하여 비지지장 및 단면 형상으로 구성되는 침강도 감소모델을 사용하였다. 개발된 2차 소성힌지해석법을 LRFD 설계방법과 비교함으로서 검증하였다. 예제해석을 통하여 횡비틀림좌굴효과는 2차 소성힌지해석법에 고려해야 할 중요한 요소임을 알 수 있었다. 본 해석은 실제 설계에 활용할 수 있는 효율적이고 신뢰성 있는 방법이다.
In this study, the torsional strength of reinforced concrete hollow beams is predicted by nonlinear finite element analysis. A nonlinear finite element analysis program, ATENA, was used for the analysis. A total of six reinforced concrete beams were used and the analysis was performed under the same conditions as the actual test.
This study focuses on the effects of load height on the inelastic lateral buckling of doubly stepped I-beams. The effects of having compact and non-compact flanges are also covered by this study. Two sections are analyzed: one having compact flanges and web while the other section has a compact web and non-compact flanges. The loadings are limited to those having an inflection point of zero. Also, the three main locations for the loads analyzed would be at the top of the flange, at the shear and at the bottom flange. The nonlinear analysis is done using the finite element program, ABAQUS. Also, to take into consideration the effect of inelastic buckling, residual stresses and geometric imperfections are applied to the models made. The results of the analysis would then determine if the location of the loads has significant effects on the buckling strength of the stepped beams. Also, the results are compared to the results of previous studies involving the effects of load-height on prismatic beams. The final results are tabulated and conclusions and new design methods are provided.