PURPOSES: The objective of this study is to evaluate and compare the stiffness characteristics and seasonal variation in surface deflections of block and asphalt pavements using the light weight deflectometer (LWD) and falling weight deflectometer (FWD).
METHODS: LWD and FWD testing was conducted on block and asphalt pavement sections in a low-impact development facility, to evaluate the structural capacity and seasonal variation in asphalt pavements. To analyze the seasonal variation in stiffness characteristics, this testing was performed in October 2016, January 2017, and March 2017 in the same drop locations.
RESULTS : It was found from that the average center deflections in the asphalt and block pavements were 218 ㎛ and 2974 ㎛, respectively. The center deflections measured using FWD testing in block pavement are 15 times those measured in asphalt pavement. It was also observed that LWD deflections in block pavements were decreased by approximately 65-90% as the air temperature dropped from 20 to 4℃. The degree of reduction in block pavement was significantly higher when compared with asphalt pavement, which showed a 25- 50% reduction in deflection.
CONCLUSIONS: When using block pavements for roadways, the structural capacity of the pavement system should be considered during the design and construction stages. In block pavements, the use of low-quality material and insufficient compaction in the base and subgrade layers can induce a reduction in structural capacity, which would lead to the need for frequent repair work. A reinforcement underneath the block layer would be an appropriate measure for improving the structural support and extending the service life.
OBJECTIVES : The objective of this study is to analyze the nonlinear behavior of block pavements using multi-load level falling weight deflectometer (FWD) deflections. METHODS: Recently, block pavements are employed not only in sidewalks, but also in roadways. For the application of block pavements in roadways, the structural capacities of subbase and subgrade are important factors that support the carry traffic load. Multi-load level FWD testing was conducted on block pavements to analyze their nonlinear behavior. The deflection ratio due to the increase in load was analyzed to estimate the nonlinearity of block pavements. Finite element method with nonlinear soil model was applied to simulate the actual nonlinear behavior of the block pavement under different levels of load. RESULTS: The results of the FWD testing show that the center deflections in block pavements are approximately ten times greater than that in asphalt pavements. The deflection ratios of the block pavement due to the increase in the load range from 1.2 to 1.5, indicating that the deflection increased by 20~50%. The material coefficients of the nonlinear soil model were determined by comparing the measured deflections with the predicted deflections using the finite element method. CONCLUSIONS: In this study, the nonlinear behavior of block pavements was reviewed using multi-load level FWD testing. The deflection ratio proposed in this study can estimate the nonlinearity of block pavements. The use of nonlinear soil model in subbase and subgrade increases the accuracy of predicting deflections in finite element method.
본 연구에서는 단지 내 아파트 블록포장 50곳의 현장조사를 통하여 주요 파손형태를 조사하여 공용성을 평가하였다. 공용성 평가결과에 따르면, 조사대상지역에서 9년의 공용연수를 가진 블록포장의 유지관리지수는 7.9에서 8.9사이이며, 블록포장의 상태는 양호한 것으로 나타났다. 따라서 건설교통부 '보도설치 및 관리지침'에 10년으로 제시된 보도의 교체주기는 검토할 필요가 있다는 결론을 도출하였다. 또한 블록포장의 공용성을 객관적으로 평가하기 위해서 일본블록포장협회에서 제시한 유지관리 기준과 건설교통부 '보도설치 및 관리지침'의 유지관리기준을 조합하여 국내 현실에 적합한 유지관리기준을 제시하였다. 외국과 비고할 때 국내의 블록포장의 기준에는 내구성 관련기준과 줄눈채움재 및 모래안정층의 품질관리 기준이 명확히 제시되어 있지 않다. 따라서 블록포장의 기대수명과 유지관리비용을 줄이기 위하여, 본 연구에서는 국내외 기준을 비교하여 이러한 기준들을 국내기준에 포함시킬 것을 제안하였다.
This study aims to measure and to analyze the characteristics of thermal environment of the various permeable pavement materials such as a break stone pavement (Green block cubic), soil protection pavement (Soil tector), soil cement pavement and ceramic brick pavement under the summer outdoor environment. The thermal environment characteristics measured in the study includes the changes of surface temperature during the day, and long and short wave radiation of each pavement surface. The experimental condition is based on the data on the hottest temperature (August 9, 2006, 37.1℃) of the year. The albedo was the highest on the break stone pavement(0.8) from 12:00 to 14:00. The albedo of the ceramic brick pavement, a soil tector pavement and soil cement pavement were 0.35, 0.29 and 0.27 from 12:00 to 14:00, respectively. The peak surface temperature and long wave radiation was the highest on the soil protection pavements(56.6℃/627 W/m2). The peak surface temperatures and long wave radiation on the ceramic brick pavement, a stone brick pavement and soil cement pavement were 51.7℃/627 W/m2, 48.8℃/607 W/m2 and 45.9℃/582 W/m2, respectively. The heat environment was better on the break stone pavement than on the other pavements. This is mainly due to the high albedo of the break stone pavement(0.8) while the albedo value of a ceramic brick pavement, a soil tactor pavement and soil cement pavement were 0.35. 0.29 and 0.27. Large heat capacity(2,629 kJ/㎥․K) of the stone brick pavements also contributes to this difference. The heat environment was better on the soil cement pavement than the soil tector pavement. This is mainly due to the evaporation of the soil cement pavement while the active evaporation of the soil tactor pavement was not continued after two days from the rainfall event. To improve the thermal environments in the urban area, it is recommended to raise the albedo of the pavements by brightening the surface color of the pavement materials. Further studies on the pavement materials and the construction methods which can enhance the continuous evapotranspiration from the pavements surface are needed.