간행물
한국도로학회논문집 KCI 등재 International journal of highway engineering
- 발행기관 한국도로학회
- 자료유형 학술지
- 간기 격월간
- ISSN 1738-7159 (Print)2287-3678 (Online)
- 수록기간 1999 ~ 2024
- 주제분류 공학 > 토목공학 공학 분류의 다른 간행물
- 십진분류KDC 534DDC 625
권호리스트/논문검색
제18권 제6호 (2016년 12월) 20건
1.
2016.12
구독 인증기관 무료, 개인회원 유료
OBJECTIVES: Currently, the market for carbon emissions trading has been increasing. In Korea, it is known that traffic mode rate in bike transportation is low. However, if bike transportation system is encouraged and the traffic mode rate is increased, it would be possible to reduce carbon emissions through the trading market. In this study, a practical policy to activate the bike transportation system in Korea will be proposed and verified. METHODS: Past studies regarding bike transportation system in international and domestic metropolitan cities were analyzed. Moreover, detailed reviews on recent carbon emissions trading market were performed. In particular, SWOT analysis on the bike transportation system in Korea and policy topology analysis were conducted. RESULTS: Based on the literature reviews and SWOT analysis, a new bike transportation policy was proposed. Several actual plans to adopt in Korea were proposed. In addition, a new bike transportation policy was analyzed using policy typology model, and a business model related to the cost of implementing the system and CERs were also proposed. CONCLUSIONS : It is concluded that the proposed bike transportation activation policy and several practical plans to connect CERs and a business model including bus, subway, T-money and bike riders to give some incentive were effective and reasonable. It is desired that this study will help Korea to get CERs through bike transportation activation in the future.
4,000원
2.
2016.12
구독 인증기관 무료, 개인회원 유료
OBJECTIVES: This study aims to review a plan to reduce the shoulder width of a deformed round-trip two-lane highway with low traffic volume. METHODS: Installation of a passing lane on a round-trip two-lane (one-way one-lane) highway, and reduction of a shoulder for a round-trip four-lane highway. RESULTS : It is necessary to establish a design criterion for various highways, because the plan to reduce the lane or shoulder width of a highway with low traffic volume was analyzed to have an economic efficiency of 6.8~7.0%. CONCLUSIONS: It is necessary to seek for a plan to establish a national trunk net early by efficiently using the limited financial resources to cope with the traffic demand elastically.
4,600원
3.
2016.12
구독 인증기관 무료, 개인회원 유료
OBJECTIVES : This is a basic research for the domestic production of airport-airside deicers. This research selected basic materials for deicers appropriate for the pavement of domestic airports by evaluating the deicing performances of basic materials used in internationalstandard airport deicers and their impacts on pavements. METHODS: Laboratory investigation was conducted to evaluate the asphalt surface tensile strength, concrete scaling impact, ASR impact, and deicing performances of sodium formate (NaFm), potassium formate (KFm), sodium acetate (NaAc), and potassium acetate (KAc), which are the basic de-icing materials commonly used at international airports, approved by the FAA. In addition, the analyses were also performed on the airside deicer urea, which is currently used in domestic airports. RESULTS : Laboratory investigation confirmed that sodium formate, potassium formate, sodium acetate, and potassium acetate had superior surface tensile strength, concrete scaling impact, and deicing performance compared to airside urea, but they also had greater impacts on concrete ASR. Among these materials, sodium formate had the best asphalt surface tensile strength, concrete scaling impact, and deicing performance, while also having the greatest impact on ASR; hence, mitigation plans for ASR were needed, if it were to be used as airport-airside deicer. CONCLUSIONS : It is necessary to consider additional additives to prevent ASR of concrete pavements when developing airport-airside deicers using sodium formate, potassium formate, sodium acetate, and potassium acetate.
4,000원
4.
2016.12
구독 인증기관 무료, 개인회원 유료
OBJECTIVES : The objective of this study is to analyze the nonlinear behavior of block pavements using multi-load level falling weight deflectometer (FWD) deflections. METHODS: Recently, block pavements are employed not only in sidewalks, but also in roadways. For the application of block pavements in roadways, the structural capacities of subbase and subgrade are important factors that support the carry traffic load. Multi-load level FWD testing was conducted on block pavements to analyze their nonlinear behavior. The deflection ratio due to the increase in load was analyzed to estimate the nonlinearity of block pavements. Finite element method with nonlinear soil model was applied to simulate the actual nonlinear behavior of the block pavement under different levels of load. RESULTS: The results of the FWD testing show that the center deflections in block pavements are approximately ten times greater than that in asphalt pavements. The deflection ratios of the block pavement due to the increase in the load range from 1.2 to 1.5, indicating that the deflection increased by 20~50%. The material coefficients of the nonlinear soil model were determined by comparing the measured deflections with the predicted deflections using the finite element method. CONCLUSIONS: In this study, the nonlinear behavior of block pavements was reviewed using multi-load level FWD testing. The deflection ratio proposed in this study can estimate the nonlinearity of block pavements. The use of nonlinear soil model in subbase and subgrade increases the accuracy of predicting deflections in finite element method.
4,000원
5.
2016.12
구독 인증기관 무료, 개인회원 유료
OBJECTIVES : In this study, microstructural components of crumb rubber modified asphalt (CRMA) binder were investigated using environmental scanning electron microscope (ESEM). To clearly understand the elemental composition of the CRMA binder, energy dispersive X-ray spectroscopy (EDX) was employed on the ESEM samples. METHODS: CRMA binders were produced using open blade mixers at 177℃ for 30 min. The binders were artificially aged through a series of accelerated aging processes. Sample preparation was done by making a mold shape on the glass slide. Thereafter, the morphology of the CRMA binder was observed using the ESEM coupled with the EDX. RESULTS : The images captured from the ESEM indicate that the unaged CRMA binder appears to have a single-phase continuous nonuniform structure after the addition of crumb rubber particles, whereas the artificially aged CRMA binder was observed to have two different phases. ESEM coupled with EDX shows detailed internal structure of the modified binders compared to other technologies (i.e., optical microscopy, atomic force microscopy, and conventional scanning electron microscope). CONCLUSIONS: The captured images resemble the internal structures such as the viscous properties of the unaged CRMA binder and the interaction between the rubber particles and the base binder at aged condition. ESEM is a powerful instrument and with the introduction of EDX, it provided more details of the network microstructure of the asphalt binder. ESEM coupled with EDX is recommended for use in future investigation of microstructure of asphalt binders.
4,000원
6.
2016.12
구독 인증기관 무료, 개인회원 유료
Estimates on appropriate storage for deicing materials for the 2018 Pyeongchang Winter Olympic Games
OBJECTIVES : The objective of this study is to estimate the appropriate storage required for deicing materials in Gangwon-do for successful snow removal operations during the 2018 Pyeongchang Winter Olympic Games. The final estimates of the deicing chemicals can be used by public agencies to aid decision making. METHODS: First, the database that exists in the road snow-removal management system (RSMS) of the Ministry of Land, Infrastructure, and Transport, South Korea was used to determine historical characteristics of snow removal experiences in Gangwon-do. The database includes historical information, including regional and road weather data and number of snow-removal works. Second, both the maximum and the actual amount of storages used for deicing materials in the past three years were analyzed. Lastly, the final estimates of the deicing materials were evaluated using an additional equation. It considers frequency of salt spray application, total administrative road length estimated by road agencies, and number of days required for snow removal works in Gangwon-do. Consequently, the results show that significant differences were not observed between the final estimates and the maximum amount used during the past three years. RESULTS: The final estimates of the deicing materials are almost similar to the maximum amount used during the past three years in Gangwon-do. CONCLUSIONS: The study shows that the estimates of deicing chemicals can be useful when decision making is required for the snowremoval policy.
4,000원
7.
2016.12
구독 인증기관 무료, 개인회원 유료
OBJECTIVES: The objective of this study is to detect road cavities using multi-channel 3D ground penetrating radar (GPR) tests owned by the Seoul Metropolitan Government. METHODS: Ground-penetrating radar tests were conducted on 204 road-cavity test sections, and the GPR signal patterns were analyzed to classify signal shape, amplitude, and phase change. RESULTS : The shapes of the GPR signals of road-cavity sections were circular or ellipsoidal in the plane image of the 3D GPR results. However, in the longitudinal or transverse direction, the signals showed mostly unsymmetrical (or symmetrical in some cases) parabolic shapes. The amplitude of the GPR signals reflected from road cavities was stronger than that from other media. No particular pattern of the amplitude was found because of nonuniform medium and utilities nearby. In many cases where road cavities extended to the bottom of the asphalt concrete layer, the signal phase was reversed. However, no reversed signal was found in subbase, subgrade, or deeper locations. CONCLUSIONS: For detecting road cavities, the results of the GPR signal-pattern analysis can be applied. In general, GPR signals on road cavity-sections had unsymmetrical hyperbolic shape, relatively stronger amplitude, and reversed phase. Owing to the uncertainties of underground materials, utilities, and road cavities, GPR signal interpretation was difficult. To perform quantitative analysis for road cavity detection, additional GPR tests and signal pattern analysis need to be conducted.
4,000원
8.
2016.12
구독 인증기관 무료, 개인회원 유료
OBJECTIVES : The objective of this study is to propose a capacity analysis methodology for riverside bike-exclusive roads. METHODS: Three steps were performed to develop a methodology to estimate bikeway capacity. First, we reviewed previous studies on the vehicle-road capacity analysis and proposed their applicability to bikeways. Second, two assumptions were made based on the traffic flow characteristics of bikeways: (1) the capacitated state in bikeways occur within a bicycle platoon, and (2) a bicycle platoon consists of more than three bicycles running in close proximity. In addition, it is assumed that the mean time headway of a bicycle platoon represents the characteristics of the platoon. The normality of the mean-time headway of a bicycle platoon calculated using the central limit theorem leads to the development of a method that estimates the riverside bikeway capacity using data collected from two different riverside bike-exclusive roads (Han-river and Anyangcheon). We used a location-fixed video camera to record videos of running bicycles and wrote a special-purpose software program to code the time-headway data from the videos. RESULTS : Time headways from 189 bicycle platoons were analyzed. The estimated mean-time headway of the capacitated bicycle flow is 1.01 s, from which the capacity of the bikeway is found to be 3578 vehicles/h. CONCLUSIONS : The proposed method that estimates bikeway capacity could be applicable to the analysis of short-range congested area rather than planning the number of lanes. In other words, it determines the sections that are temporarily highly congested and proposes appropriate strategies to mitigate the congestion.
4,000원
9.
2016.12
구독 인증기관 무료, 개인회원 유료
OBJECTIVES : A fog generated field test was conducted to analyze the relationship between the luminance of variable speed-limit signs and the legibility distance under various fog density conditions. By using this study, appropriate luminance values can be selected depending on the density of fog. METHODS: An actual tunnel was selected as the area to conduct the test, as other places cannot maintain the fog condition because of rapid air current. Ninety-two subjects were recruited for this test, which took place during the course of three days. Visibility-distance detecting sensor was used to measure the visibility distance due to the fog density time, simultaneously with the evaluation of legibility distance by subjects. RESULTS: The test results show the relationship between luminance values and the legibility distance corresponding to the visibility distance due to fog. According to the technical test results, lower luminance value such as 7000 cd/m2 corresponds to less legibility distance compared to higher values such as 20000 cd/m2 or 40000 cd/m2. However, the amount of difference between 20000 cd/m2 and 40000 cd/m2 is negligible in our test. CONCLUSIONS: The results of this study can be used to select appropriate luminance of valuable speed signs under fog conditions. Hence, drivers can expect to have more room to respond to adverse weather conditions, thereby reducing the risk of accidents.
4,000원
10.
2016.12
구독 인증기관 무료, 개인회원 유료
OBJECTIVES : A fog generated field test was conducted to analyze the relationship between different sizes of variable speed limit signs and the legibility distance under various fog density conditions. By using this study, appropriate sizes of signs can be selected depending on the density of fog. METHODS : An actual tunnel was selected as the area for this test, as other places cannot maintain the fog condition because of rapid air current. A total 121 subjects were recruited for this test, which took place over the course of four days. The test on the first day was conducted under normal weather conditions for comparison. Visibility-distance detecting sensor was used to measure the visibility distance due to the fog density time, simultaneously with the evaluation of legibility distance by subjects. RESULTS : The test results show the relationship between the different sizes of signs and the legibility distance corresponding to the visibility distance due to both non-fog and fog generated conditions. According to the technical test results, appreciable amount of reduction in legibility distance due to fog was resulted in all sizes of signs. Moreover, the legibility distance is reduced proportionately with the decrease in the visibility distance due to fog. CONCLUSIONS : The results of this study can be used to select appropriate sizes of valuable speed signs under fog conditions. Hence, drivers can expect to have more room to respond to adverse weather conditions, thereby reducing the risk of accidents.
4,000원
11.
2016.12
구독 인증기관 무료, 개인회원 유료
OBJECTIVES: The objective of this research is to develop additives for the modification of Solvent DeAsphalting Residue (SDAR) to be used as pavement materials, and evaluate the performance of asphalt mixture manufactured using the SDAR modified by developed additives. METHODS: The SDAR generally consists of more asphaltenes and less oil components compared to the conventional asphalt binder, and hence, the chemical/physical properties of SDAR are different from that of conventional asphalt binder. In this research, the additives are developed using the low molecular oil-based plasticizer to improve the properties of SDAR. First, the chemical property of two SDARs is analyzed using SARA (saturate, aromatic, resin, and asphaltene) method. The physical/rheological properties of SDARs and SDARs containing additives are also evaluated based on PG-grade method and dynamic shear-modulus master curve. Second, various laboratory tests are conducted for the asphalt mixture manufactured using the SDAR modified with additives. The laboratory tests conducted in this study include the mix design, compactibility analysis, indirect tensile test for moisture susceptibility, dynamic modulus test for rheological property, wheeltracking test for rutting performance, and direct tension fatigue test for cracking performance. RESULTS : The PG-grade of SDARs is higher than PG 76 in high temperature grades and immeasurable in low temperature grades. The dynamic shear modulus of SDARs is much higher than that of conventional asphalt, but the modified SDARs with additives show similar modulus compared to that of conventional asphalt. The moisture susceptibility of asphalt mixture with modified SDARs is good if, the antistripping agent is included. The performance (dynamic modulus, rutting resistance, and fatigue resistance) of asphalt mixture with modified SDARs is comparable to that of conventional asphalt mixture when appropriate amount of additives is added. CONCLUSIONS: The saturate component of SDARs is much less than that of conventional asphalt, and hence, it is too hard and brittle to be used as pavement materials. However, the modified SDARs with developed additives show comparable or better rheological/physical properties compared to that of conventional asphalt depending on the type of SDAR and the amount of additives used.
4,000원
12.
2016.12
구독 인증기관 무료, 개인회원 유료
OBJECTIVES: This study is to develop the optimum mixing proportions for cement concrete pavement with using recycled aggregates. METHODS: The mixture varied recycled coarse aggregates content from 50 % to 100 % to replace the natural coarse aggregates by weight. Tests for fundamental properties as a cement concrete pavement were conducted before and after hardening of the concrete. RESULTS: It was found that the variation in the amount of the recycled aggregate affected the compressive and flexural strength development, as well as the chloride ion penetration resistance. As the amount of the recycled aggregate content increased the compressive and flexural strength and the resistance to chloride ion penetration decreased. However, the resistance to freeze-thaw reaction was affected significantly. In addition, the gradation of the aggregate became worse and hence so did the coarseness factor as the recycled aggregate amount increased. CONCLUSIONS : The fundamental properties of the concrete with recycled aggregate does not seem to be appropriate when the recycled aggregate quality is not guaranteed up to a some level and its replacement ratio is over 50%. The optimized gradation of the aggregates should also be sought when the recycled aggregate is used for the cement concrete pavement materials.
4,000원
13.
2016.12
구독 인증기관 무료, 개인회원 유료
OBJECTIVES : This study develops an evaluation method, which is useful to inspect pavement condition of specific boroughs. This is because pavement condition is broadly divided into five grades via visual inspection, which does not consider the types of deteriorations, and is decided by an investigator having a subjective viewpoint. This visual inspection method is not a satisfactory method for accurate maintenance when various deteriorations occur. METHODS: The performance model considers several factors such as crack, rutting, and IRI. This method is also modified from borough SPI based on SPI (Seoul Pavement Index). Considering limited budget of borough, PI (prediction index) is suggested, which is related to the grade of pavement condition evaluation and type of materials. Practical correlation review is also conducted with statistical verification by using the Monte Carlo simulation. RESULTS: The results of the study show that modified criteria are reasonable. First, the comparison between the visual inspection result and the SPI result indicates that the R-square value is sufficiently high. Second, through the common section, each evaluation method could be compared, and the result shows considerable similarity, which increases when the range is modified. Finally, PI for predicting remaining life and the random number SPI have common parts, which means that each indicator would be adequate to be used as an evaluation method. CONCLUSIONS : Comparison and analysis results show that the developed evaluation method is reasonable for specific boroughs where financial support is inadequate for the evaluation process by using the newer equipment. Moreover, for more accurate evaluation method, previous visual inspection data should be utilized, and the database of inspection equipment have to be collected.
4,000원
14.
2016.12
구독 인증기관 무료, 개인회원 유료
OBJECTIVES : The objective of this research is to determine the moisture resistance of the freeze-thaw process occurring in low-noise porous pavement using either hydrated-lime or anti-freezing agent. Various additives were applied to low-noise porous asphalt, which is actively paved in South Korea, to overcome its disadvantages. Moreover, the optimum contents of hydrated-lime and anti-freezing agent and behavior properties of low-noise porous asphalt layer are determined using dynamic moduli via the freeze-thaw test. METHODS: The low-noise porous asphalt mixtures were made using gyratory compacters to investigate its properties with either hydratedlime or anti-freezing agent. To determine the dynamic moduli of each mixture, impact resonance test was conducted. The applied standard for the freeze-thaw test of asphalt mixture is ASTM D 6857. The freeze-thaw and impact resonance tests were performed twice at each stage. The behavior properties were defined using finite element method, which was performed using the dynamic modulus data obtained from the freezethaw test and resonance frequencies obtained from non-destructive impact test. RESULTS: The results show that the coherence and strength of the low-noise porous asphalt mixture decreased continuously with the increase in the temperature of the mixture. The dynamic modulus of the normal low-noise porous asphalt mixture dramatically decreased after one cycle of freezing and thawing stages, which is more than that of other mixtures containing additives. The damage rate was higher when the freeze-thaw test was repeated. CONCLUSIONS : From the root mean squared error (RMSE) and mean percentage error (MPE) analyses, the addition rates of 1.5% hydrated-lime and 0.5% anti-freezing agent resulted in the strongest mixture having the highest moisture resistance compared to other specimens with each additive in 1 cycle freeze-thaw test. Moreover, the freeze-thaw resistance significantly improved when a hydrated-lime content of 0.5% was applied for the two cycles of the freeze-thaw test. Hence, the optimum contents of both hydrated-lime and anti-freezing agent are 0.5%.
4,000원
15.
2016.12
구독 인증기관 무료, 개인회원 유료
OBJECTIVES : The objective of this research is to determine the integrity of pavement structures for areas where voids exist. Furthermore, we conducted the study of voided-area analysis and remaining life prediction for pavement structures using finite element method. METHODS : To determine the remaining life of the existing voided areas under asphalt concrete pavements, field and falling weight deflectometer (FWD) tests were conducted. Comparison methods were used to have better accuracy in the finite element method (FEM) analysis compared to the measured surface displacements due to the loaded trucks. In addition, the modeled FEM used in this study was compared with well-known software programs. RESULTS : The results show that a good agreement on the analyzed and measured displacements can be obtained through comparisons of the surface displacement due to loaded trucks. Furthermore, the modeled FEM program was compared with the available pavement-structure software programs, resulting in the same values of tensile strains in terms of the thickness of asphalt concrete layers. CONCLUSIONS: The study, which is related to voided-area analysis and remaining life prediction using FEM for pavement structures, was successfully conducted based on the comparison between our methods and the sinkhole grade used in Japan.
4,000원
16.
2016.12
구독 인증기관 무료, 개인회원 유료
OBJECTIVES: Bituminous materials, such as tack coat, are utilized between pavement layers for improving the bond strength in pavement construction sites. The standards regarding the application of bituminous material are not clearly presented in the Korean construction guideline without RS(C)-4. Hence, the objective of this study is to determine the optimum content of bituminous materials by analyzing interlayer shear strength (ISS) from the direct shear tester, which was developed in this research. The shear strength of tack coat was defined with the sort of bituminous materials. METHODS : The mixtures for the shear test were made using marshall mix design. The specimens were vertically and horizontally separated for the direct shear test. The separated specimens were bonded using bituminous material. The objectives of the experiment are to determine the performance of bond and shear properties resulting from slippage, rutting, shovel, and corrugation of asphalt pavements. A machine based on the Louisiana interlayer shear strength tester (LISST) of NCHRP Report-712 was developed to determine the ISS. The applied types of tack coat were RS(C)-4, AP-3, QRS-4, and BD-coat with contents of 0.3ℓ/m2, 0.45ℓ/m2, 0.6ℓ/m2, and 0.8ℓ/m2, respectively. RESULTS: Table 2 gives the results of the direct shear test using the developed shear machine. The BD-coat type indicated the highest average ISS value compared to the others. Between the surface and binder course, optimum tack coat application rates for AP-3, RS(C)-4, QRS-4, and BD-Coat were 0.6ℓ/m2, 0.3ℓ/m2, 0.6ℓ/m2, and 0.45ℓ/m2, respectively. These optimum contents were determined using the ISS value. CONCLUSIONS: The ISS values of AP-3, RS(C)-4, and QRS-4 showed similar tendencies when ISS increased in the range 0.3~0.6ℓ/m2, while ISS decreased when the applied rate exceeded 0.6ℓ/m2. Similarly, the highest ISS value of the BD-coat was observed when the applied rate was 0.45 ℓ/m2. However, shear strength was similar to the maximum value of ISS when the tack-coat application rate of BD-Coat exceeded 0.45ℓ/m2.
4,000원
17.
2016.12
구독 인증기관 무료, 개인회원 유료
OBJECTIVES : Visibility at night can be improved by using retroreflection for short distances and phosphorescent line markings for long distances. In this study, we analyzed the characteristics of the phosphorescent line marking through a laboratory luminance test. Field performance analysis was performed through tests conducted on the road. We also examined the luminance measurement methods using the digital image obtained during the phosphorescent visibility evaluation. METHODS : In this study, the laboratory luminance test of the phosphorescent line marking was conducted using seven specimens to characterize the luminance changes according to the type of the glass beads, the thickness of the phosphorescent line marking, and the brightness and irradiation time of the light source. Phosphorescent and general line markings were made at 150 m to investigate the field luminance performance. A preliminary review of the luminance measurement methods was made using a digital image from a digital singlelens reflex (DSLR) camera. The measured luminance ratio of the general and the phosphorescent line markings was compared with the calculated luminance ratio using luminance analysis. RESULTS: Through the laboratory luminance test, it was seen that the change in luminance, which corresponds to the brightness of the light source, appears large but the influence of the thickness and irradiation time is low. The field performance test of the phosphorescent line marking conducted on the road involved measuring the luminance on the day the marking was made and 7 days after the marking was made. The luminance was found to be 190 mcd/m2 at 30 min after sunset and approximately 10-12 mcd/m2 4h after sunset. The results of the luminance test were captured using a digital image for each time group. The luminance ratio of the phosphorescent line marking, when compared to that of the general line marking, showed a similar trend within a 13% maximum error. Additionally, when this luminance ratio is compared to the direct field measurement, it could be confirmed that the luminance ratio, as captured in the digital image, showed a similar tendency. CONCLUSIONS : 1) The change in luminance corresponding to the brightness of the light source is significant in comparison with that corresponding to the thickness and the irradiation time. In addition, the results of the field test for the phosphorescent line marking satisfied the phosphorescent fire protection standard. 2) We examined the validity of the luminance measurement method using a digital image and we concluded that the change in the luminance ratio shows a similar tendency in both the cases. The results can form the basis for luminance measurement methodology for the construction and maintenance of phosphorescent line markings.
4,000원
18.
2016.12
구독 인증기관 무료, 개인회원 유료
OBJECTIVES : The objective of this study is to develop a traffic accident model of a roundabout based on the type of land use. METHODS : The traffic accident data from 2010 to 2014 were collected from the“ traffic accident analysis system (TAAS)”data set of the Road Traffic Authority. A multiple linear regression model was utilized in this study to analyze the accidents based on the type of land use. Variables such as geometry and traffic volume were used to develop the accident models based on the type of land use. RESULTS : The main results are as follows. First, the null hypothesis that the type of land use does not affect the number of accidents is rejected. Second, four accident models based on the type of land use have been developed, which are statistically significant (high R2 values). Finally, the total entering and circulating volumes, area of the central island, number of speed breakers, mean number of entry lanes, diameter of the inscribed circle, mean width of the entry lane, area of the roundabout, bus stops, and number of circulatory roadways are analyzed to see how they affect the accident for each type of land use. CONCLUSIONS: The development of the accident models based on the type of land use has revealed that the accident factors at a roundabout are different for each case. Thus, more speed breakers in commercial areas and an inscribed circle of proper diameter in commercial and residential areas are determined to be important for reducing the number of accidents. Additionally, expanding the width of the entry lanes, decreasing the area of the roundabouts in residential areas, and reducing the conflict factors such as bus stops in green spaces are determined to be important.
4,000원
19.
2016.12
구독 인증기관 무료, 개인회원 유료
OBJECTIVES : Many roadway departure crashes on the freeway interchange are due to the running speed being greater than the design speed. This study aims to ensure a safe and pleasant driving experience for the driver by increasing the superelevation based on the running speed on the highway interchange ramp. METHODS: The mean running speed for each type of ramp is calculated on site survey more than 10 interchanges. Using the mean running speed, we calculated the superelevation and the side friction using the method given in “A Policy on Geometric Design of Highways and Street”(Pages 145-166, 2001). Then, we applied the modified method to the superelevation range. Finally, we ensured safety using the Degree of Safety that is proven by the centrifugal acceleration ratio as suggested by Joseph Craus (1978). RESULTS : The mean running speeds are 50 km/h and 65 km/h when the design speeds are 40 km/h and 50 km/h, respectively. After the application of the new method used in this study, the superelevation will be increased by 9.0% and 10.0% when the mean running speeds are 50 km/h and 65 km/h, respectively. CONCLUSIONS: A higher superelevation can give the driver a more comfortable and safe driving environment. However, the driver needs to be aware of snow and low-temperature conditions.
4,200원
20.
2016.12
구독 인증기관 무료, 개인회원 유료
OBJECTIVES : Fixed roadside objects are a threat to drivers when their vehicles deviate from the road. Therefore, such roadside objects need to be suitably dealt with to decrease accidents. This study determines the factors affecting the severity of accidents because of fixed roadside objects. METHODS : This study analyzed the crash severity impact of fixed roadside objects by using ordered probit regression as the analysis methodology. In this research, data from 896 traffic accidents reported in the last three years were used. These accidents consisted of sole-car accidents, fixed roadside object accidents, and lane-departure accidents on the national highway of Korea. The accident severity was classified as light injury, severe injury, and death. The factors relating to the road and the driver were collected as independent variables. RESULTS: The result of the analysis showed that the variables of the crash severity impact are the collision location (left side), gender of the driver (female), alcohol use, collision facility (roadside trees, traffic signals, telephone poles), and type of road (rural segments). Additionally, the collision location (left side), gender of the driver (female), alcohol use, collision facility (street trees, traffic signals, telephone poles), and type of road (rural segments), in order of influence, were found to be the factors affecting the crash severity in accidents due to fixed roadside objects. CONCLUSIONS: An alternative solution is urgently required to reduce the crash severity in accidents due to fixed roadside objects. Such a solution can consider the appropriate places to install breakaway devices and energy-absorbing systems.
4,000원
