간행물
한국도로학회논문집 KCI 등재 International journal of highway engineering
- 발행기관 한국도로학회
- 자료유형 학술지
- 간기 격월간
- ISSN 1738-7159 (Print)2287-3678 (Online)
- 수록기간 1999 ~ 2024
- 주제분류 공학 > 토목공학 공학 분류의 다른 간행물
- 십진분류KDC 534DDC 625
권호리스트/논문검색
제15권 제5호 (2013년 10월) 24건
1.
2013.10
구독 인증기관 무료, 개인회원 유료
PURPOSES : This study is to develop a method to evaluate lubrication of asphalt binder using WMA additives and compare their lubrication effects on two types of WMA additives and three types of asphalt film thicknesses. METHODS : This study is based on laboratory experiments and rheological analysis of the experimental results. Testing materials are aggregate diskes, asphalt, and WMA additives. The main testing method is stress sweep test by using dynamic shear rheometer (DSR). RESULTS : Sasobit gives more lubrication effects on film thicknesses 0.2mm and under but LEADCAP does on film thicknesses over 0.3mm. CONCLUSIONS : LVE-Limit is a better parameter to discern the lubrication effects on the thin film asphalt thickness. Both Sasobit and LEADCAP WMA additives provide effective lubrication at the compaction temperature.
4,000원
2.
2013.10
구독 인증기관 무료, 개인회원 유료
PURPOSES : The objective of this study is to evaluate the applicability of the pitch, which is produced during SDA petroleum upgrading process, as a pavement paving material. In order for the purpose, the physical and chemical properties of the pitch are analyzed, and then the various plasticizers are applied in the pitch. METHODS: Two types of pitch are selected from oil refinery companies, which are owned the SDA petroleum upgrading process. Also, two types of asphalt binders, PG 64-22 and PG 58-22, are employed to compare with the pitch because these two types of asphalt binders are currently used as paving materials. For the chemical property of the pitch, the composition of SARA (Saturate, Aromatic, Resin, Asphaltene), the elementary composition, and the functional group are analyzed. For the physical property of the pitch, the basic material property tests, such as penetration test, softening point test, flash point test, ductility test, and rotational viscometer test, are performed. Also, the DSR (Dynamic Shear Rheometer) test and the BBR (Bending Beam Rheometer) test are conducted using asphalt binder specimens obtained by both short term aging (Rolling Thin Film Oven, RTFO) and long term aging (Pressure Aging Vessel, PAV) processes. The rheological property of each pitch type is evaluated as a function of temperatures and loading cycles. PG 64-22 asphalt binder is used as a control material. RESULTS AND CONCLUSIONS: The Pitch may not be suitable for the pavement paving material without modifications, but the pitch can be used as alternatives of modified addictive or asphalt. If low molecular component, such as saturate and aromatic components, are added in the pitch based on the development of various plasticizers, it has a strong possibility for the pitch to be used as a alternative. However, in order to verify the performance property of the pitch, further research is needed.
4,000원
3.
2013.10
구독 인증기관 무료, 개인회원 유료
PURPOSES : This study is to suggest time to spray curing compound, the amount of curing compound, and the number of times to spray curing compound based on indoor tests. METHODS : Based on the literature review, two methods are used in this study, One is test for water retention of concrete curing material and the other is test for abrasion resistance of concrete surfaces by the rotating-cutter method. Through those methods, curing compound was evaluated. RESULTS : The result of the laboratory experiment for time to spray curing compound indicates that 30 minutes after placing concrete is optimal. For the amount of curing compound, 0.5l/m2 is the minimum quantity for both concretes. Through test of the number of times to spray curing compound, method to spray the whole amount of curing compound in twice is more efficient than it to spray the whole amount at a time. Also, method of separately 30-50 minutes spray is better than method of separately 10-30 minutes spray. CONCLUSIONS : From the testing results, it can be proposed that optimum time to curing compound is 30±15 minutes, 0.5l/m2 is efficient for spraying the whole amount of curing compound at a time, and 0.4l/m2 is the best for spraying the whole amount of curing compound in twice, which sprays it in 20 minutes after 30 minutes from placing concrete.
4,000원
4.
2013.10
구독 인증기관 무료, 개인회원 유료
PURPOSES: Simulation of aggregate slump test using equivalent sphere particle in DEM and its validity evaluation against lab aggregate slump test METHODS : In this research, aggregate slump tests are performed and compared with DEM simulation. To utilize spheric particles in YADE, equivalent sphere diameter concept is applied. As verification measures, the volume in slump cone filled with aggregate is used and it is compared with volume in slump cone filled with equivalent sphere particle. Slump height and diameter are also used to evaluate the suggested numerical method with equivalent concept RESULTS : Simulation test results show good agrement with lab test results in terms of loose packing volume, height and diameter of slumped particle clump. CONCLUSIONS : It is concluded that numerical simulation using DEM is applicable to evaluate the effect of aggregate morphological property in loose packing and optimum gradation determination based on the aggregate slump test simulation result.
4,000원
5.
2013.10
구독 인증기관 무료, 개인회원 유료
PURPOSES : Determination of particle packing model variables that can be used for formulation of new DEM based particle packing model by examining existing particle packing models METHODS : Existing particle packing models are thoroughly examined by analytical reformulation and sensitivity analysis in order to set up DEM based new particle packing model and to determine its variables. All model equations considered in this examination are represented with consistent expressions and are compared to each others to find mathematical and conceptual similarity in expressions. RESULTS : From the examination of existing models, it is observed that the models are very similar in their shapes although the derivation of the models may be different. As well, it is observed that variables used in some existing models are comprehensive enough to estimate particle packing but not applicable to DEM simulation. CONCLUSIONS : A set of variables that can be used in DEM based particle packing model is determined.
4,800원
6.
2013.10
구독 인증기관 무료, 개인회원 유료
PURPOSES : The purpose of this study is to investigate the optimal joint positions which can minimize distresses of concrete pavement containing box culvert with horizontally skewed angles. METHODS : The concrete pavement containing the box culvert with different skewed angles and soil cover depths was modeled by 3 dimensional finite element method. The contact boundary condition was used between concrete and soil structures in addition to the nonlinear material property of soil in the finite element model. A dynamic analysis was performed by applying the self weight of pavement, negative temperature gradient of slab, and moving vehicle load simultaneously. RESULTS : In case of zero skewed angle (0˚), the maximum tensile stress of slab was the lowest when the joint was positioned directly over side of box culvert. In case there was a skewed angle, the maximum tensile stress of slab was the lowest when the joint passed the intersection between side of the box culvert and longitudinal centerline of slab. The magnitude of the maximum tensile stress converged to a constant value regardless the joint position from 3m of soil cover depth at all of the horizontally skewed angles. CONCLUSIONS : More reasonable and accurate design of the concrete pavement containing the box culvert can be possible based on the research results.
4,000원
7.
2013.10
구독 인증기관 무료, 개인회원 유료
PURPOSES : It is to evaluate lightweight soil as a subgrade material based on mechanical tests and calculation of pavement performance. METHODS : In this research, various contents of cement and air foam are used to make lightweight soil using wasted dredged soil. Uniaxial compressive strength test is conducted to evaluate strength of 7 and 28 day cured specimens. Secant modulus was calculated based on the stress and strain relationship of uniaxial compressive strength test. Resilient modulus test was measured using by repeated triaxial compression test. The measured resilient modulus was used in layered elastic program to predict fatigue and rutting life at a given pavement structure. RESULTS : Uniaxial compressive strength increases as cement content increases but decrease as air foam content increases. Resilient modulus also increases as cement content increases and decrease as air foam content decrease. CONCLUSIONS : It is concluded that dredge clay soil can be used as subgrade layer material using by lightweight treated soil method.
4,000원
8.
2013.10
구독 인증기관 무료, 개인회원 유료
PURPOSES : This study is to suggest future development direction and application of environmental noise barriers as multi-functional soundproof wall. METHODS : Based on the literature review, case study and patent search, research and patent trend were investigated. Patent search was conducted by Patent searching tools, 'Focust'. RESULTS : As environmental noise barriers, Vegetative soundproof wall, photovoltaic soundproof wall, and air-pollution reduction soundproof wall were investigated. First of all, In Korea, Vegetative soundproof wall is being developed mostly as soundproof wall that has vegetation foundation inside, to meet the domestic condition with 23 patent applications. Second, Photovoltaic soundproof wall is being developed mainly with efficiency of photovoltaic system rather than soundproofing. And it is limited to one generation solar cell technology, although Solar cell technology is developing at a rapid pace. On the other hand, for reducing air-pollutant by soundproof wall, a variety of methods are being suggested (filtration, adsorption, and photocatalytic oxidation), and one of them, adsorption are applied for developing air pollution reduction soundproof wall in Korea. CONCLUSIONS: The above soundproof wall is not simple structure, but road facility applied fusion technique. Therefore, as one system, it is difficult to harmonize due to various considerations for design factor. However, if it's possible that a benefits of one system apply to another system, Synergy effect may be created. In the foreseeable future, soundproof wall may be considered as a road system using fusion technique rather than just functional facility. Therefore, substantial studies for applying multi-functional soundproof wall on the road are needed for the future.
4,000원
9.
2013.10
구독 인증기관 무료, 개인회원 유료
PURPOSES : The objective of this study is to evaluate the environmental resistance of bio-polymer concrete for use of pavement materials developed for reducing the carbon-dioxide. METHODS : The compression, tension, and bending strength tests were conducted on the bio-polymer concrete specimens with and without environmental conditioning. The specimens were conditioned using the freezing-thaw and accelerated weathering process for long period of time. To assess the resistance against chloride, the chloride ion penetration resistance tests were carried out on the bio-polymer concrete specimens. RESULTS : Test results show that the maximum difference in strength between specimens with and without conditioning is about 2.6MPa indicating that the effect of environmental conditioning on specimen strength is negligible. Based on the chloride ion penetration resistance test, the penetration quantity of electric charge of the specimens is zero and there is no ion penetration within the bio-polymer concrete. CONCLUSIONS : It is found from this study that there is slight change in strength of bio-polymer concretes before and after environmental conditioning process and no chloride ion penetration observed in these specimens. Therefore, the developed bio-polymer concretes can be applied effectively as pavement materials due to the small change of physical properties with environment change.
4,000원
10.
2013.10
구독 인증기관 무료, 개인회원 유료
PURPOSES : This study is to evaluate ASR(alkali silica reactivity) resistance of ternary blended binder adding ultra fine mineral admixture. METHODS : This study analyzes ASR expansion using ASTM C 1260 and 1567. RESULTS : This study showed that the fineness of mineral admixture had no effect on ASR expansion. The expansion of ternary blended binder(UFFA 20%+FGGBS 10%) were below 0.1%, and this binder met the ASR standard. Also when adding the CSA expansion agent, ASR expansion slightly decreased. The expansion of latex modified mixture increased by 80% comparing plain mixture. CONCLUSIONS : Ternary blended binder met the ASR standard, and this binder is available in concrete bridge deck overlay.
4,000원
11.
2013.10
구독 인증기관 무료, 개인회원 유료
PURPOSES : This study aims at proposing the methodology for benefit evaluations in pavement maintenance methods and timings using KoPMS(Korean Pavement Management System) software which was developed for efficient pavement management. METHODS : This study classified pavement sections into 4 clusters considering AADT(Annual Average Daily Traffic) and ESAL(Equivalent Single-Axle Load) using cluster analysis and used the deterioration models in each cluster. Increased user costs due to pavement deterioration as time goes by and agent costs for maintenance were estimated. Based on deterioration model and KoPMS software, Methodology for benefit evaluation was proposed in pavement maintenance methods and with/without implementation using real pavement section data. RESULTS : This study verified that considering agent costs only would be constrained to decide pavement maintenance methods and timings, and ascertained that decision making with agent and user costs would be effective. In addition, this study revealed that pavement maintenance methods and timings can be affected by AADT and ESAL and frequent pavement maintenances can be more efficient for benefits in pavement sections with more AADT and ESAL. Also this study found that user costs would be more affected to decision making than agent costs. Moreover, Delay of conducting pavement maintenance caused increased vehicle operating costs and environmental costs because of poor conditions of pavements. CONCLUSIONS : This study proposed LCCA and benefit estimation methodology of pavement with considering agent and user costs. The results of this study can be used for baseline data of efficient pavement asset management.
4,000원
12.
2013.10
구독 인증기관 무료, 개인회원 유료
PURPOSES : The purpose of this study is to evaluate the durability of ternary blended concrete mixtures adding ultra fine admixture. METHODS : From the literature review, crack was considered as the main distress failure criterion on concrete bridge deck pavement. To reduce the initial crack development due to drying shrinkage, CSA expansion agent and shrink reduction agent were used to ternary blended concrete mixtures as a admixture. Laboratory tests including chloride ion penetration test, surface scaling test, rapid freeze & thaw resistance test, non restrained drying shrinkage and restrained drying shrinkage test were conducted to verify the durability of ternary blended concrete mixtures. RESULTS : Based on the test results, proposed mixtures were verified as high qualified durable materials. Expecially initial drying shrinkage crack was not occurred in ternary blended concrete mixtures with CSA expansion agent. CONCLUSIONS : It is concluded that the durability of proposed ternary blend concrete mixture was acceptable to apply for the concrete bridge deck pavement.
4,000원
13.
2013.10
구독 인증기관 무료, 개인회원 유료
PURPOSES : The purpose of this system (Rear Lighting System) is to provide illumination for the driver to operate the commercial vehicle safely after dark in highway, to increase the conspicuity of the vehicle, and especially be suggesting the finest observable improvement method, depending on color and pattern of rear lighting system of truck for midnight highway traffic. METHODS : Rear lightning system as an improving way for forward commercial vehicles lighting the securing sight from human factors and the surrounding environment in midnight driving. For this one, basic materials were collected from the data analysis about many types of problems, and filed investigation for establishing Driving Simulator. also taking statistic test to human volunteers after finding recognizable distance of them. RESULTS : As a result, color with the highest visuality is amber followed by green-red-blue as in order for all road types. Especially almost no difference is found between red and green, also when the light is turn off, recognizable distances is wide difference compared to turn on the light. One more thing about study per pattern, upper and entire lighting have similar recognizable distances, but under lighting shows short distance with difficulty securing sight from medians. And straight section shows similar recognizable distances. By finding visuality improvement method depending on color and pattern of supplement taillight, it is expected to suggest quantitative judgement standard for introducing regulation and improvement of supplement taillight. CONCLUSIONS : Night time vehicle conspicuity to the rear is provided by rear position lamps. this study is showed that the color of light ramp is not important to be safe driving, most important is to turn on the light, recognizable distances is big different compared to turn off the rear light, so when the drivng dark in highway, have to turn on the light for reducing risk.
4,300원
14.
2013.10
구독 인증기관 무료, 개인회원 유료
PURPOSES : The present paper is to compare vehicles' CO2 emissions in roundabouts and signalized intersections. METHODS : The present paper uses the SIDRA software with variables of traffic and road conditions. RESULTS : The results of the study are as follows : First, when entering traffic volumes are more than 1600pcph, vehicle's CO2 emissions in roundabouts are lower than those of signalized intersections regardless of the left turn ratio. Second, When entering traffic volumes are more than 2800pcph, vehicles's CO2 emissions in 2-lane approaches are lower than those of 1-lane approaches in signalized intersection. Third, when entering traffic volumes are more than 1600pcph, vehicle's CO2 emissions of CASE B are lowest. (CASE B is the condition with one exclusive left-turn lane and one exclusive straight lane and one shared straight lane with right-turn.) Also, CASE A is the condition that vehicle's CO2 emissions in roundabouts are lower than those of signalized intersections between 1600pcph and 3600pcph. (CASE A is the condition with one exclusive left-turn lane and one shared straight lane with right-turn.) But, when entering traffic volumes are more than 4000pcph, vehicle's CO2 emissions in signalized intersections is lower than those of roundabouts. CONCLUSIONS : It may be concluded that vehicle's CO2 emissions on roundabouts are much lower than those of signalized intersections, especially, when entering traffics volumes are between 1600pcph and 3600pcph in 1-lane or 2-lane approaches.
4,200원
15.
2013.10
구독 인증기관 무료, 개인회원 유료
PURPOSES : The purpose of this paper is to develop a methodology to estimate level of service of arterial including Exclusive Median Bus Lanes. METHODS : On 6 Exclusive Median Bus Lanes routes in Seoul, bus travel time and number of bus-stop per km were investigated. Also whether or not passing lane exists at bus-stop was checked. Based on the data from sites, bus travel time was estimated according to length of segment, number of bus-stop per km and whether or not passing lane exists at bus-stop. RESULTS : A bus travel time table was developed according to length of segment, number of bus-stop per km and whether or not passing lane exists at bus-stop. After bus travel speed and passenger car travel speed is estimated based on each travel time table and length of segment, two speeds are combined with weighted average speed using traffic volume of each lane group. Then weighted average speed is a measure of effectiveness of arterial including Exclusive Median Bus Lanes. CONCLUSIONS : It can be concluded that the proposed methodology can estimate level of service of arterial including Exclusive Median Bus Lanes considering the operation characteristics of Exclusive Median Bus Lanes.
4,000원
16.
2013.10
구독 인증기관 무료, 개인회원 유료
PURPOSES : This research is a study on the changes in the road network of the surrounding area is installed according to the Kiss & Ride Zone. METHODS : Estimating the transportation mode of students by using the Metropolitan household Surveys(2006) and estimating the O/D by Kiss & Ride ratio with the estimated data, then being applied to a method of reducing the number of lanes for certain sections of the road which would be installed with Kiss & Ride Zone. RESULTS : The reason why it is different for delay resolving time and the affected roads as the Kiss & Ride percentage change, was the impact of the Kiss & Ride Zone's installation position. CONCLUSIONS : The purpose of the study was to analyze the impact of the road network in accordance with the installation of Kiss & Ride Zone by using speed and queue delay resolving time, and it is a need to develop a quantitative evaluation technique which was using various indicators in impact analysis according to the installation of the traffic safety facilities in the future.
4,300원
17.
2013.10
구독 인증기관 무료, 개인회원 유료
PURPOSES : This study is to analyze expected effect of a accident decrease when motorcycle safety inspection is introduced. METHODS : Based on the literature review of effect of 4-wheel vehicle inspection, probability of occurring accidents among defective motorcycles are calculated by using the number of estimated defective motorcycles and accidents resulting from defects of motorcycles. Then, the number of decreased accidents which is resulting from eliminating defects of motorcycles by safety inspection is estimated by using probability of occurring accidents among defective motorcycles. RESULTS : If the ratio of eliminating defects of motorcycles is 95% after motorcycle safety inspection, the effects of accident decrease of motorcycle safety inspection are analyzed from 2005 to 2008. As a result, 46,292 defective motorcycles are repaired and 1,376 accidents are prevented when the probability of occurring accidents among defective motorcycles is 2.97%. CONCLUSIONS : This study suggests the expected effect of motorcycle safety inspection is that the inspection can prevent 1,376 motorcycle accidents. However, the number of preventing motorcycle accidents are small, compared with the total number of motorcycle accidents because there are limitations to investigate the causes of defective motorcycle accidents. A more precise analysis of the expected effect of motorcycle inspection is possible when a systematic investigation of the causes of the accidents is implemented.
4,000원
18.
2013.10
구독 인증기관 무료, 개인회원 유료
PURPOSES : Lately, a traffic information market has been developed with a rapid speed owing to information and communications. In this situation, a study on the use intention and the satisfaction of mobile transportation information applications of users will be diverse implications and a strategic foundation to local governments and transportation information related enterprises that should provide satisfactory info as public goods to much more users. METHODS : Going along with the flow, this study establishes features of the mobile transportation information applications aiming to the users and analyzes empirical causality for effects of the use intension and the satisfaction. Through this study's analysis, targeting users having experienced transportation information applications among smart phone users, a survey was conducted and characteristics of the transportation information applications were lighted and the effects of the use intention and the satisfaction were analyzed using a technology acceptance model. RESULTS : The analysis result was that Accuracy, Riskiness, Ubiquity and Interactivity as all attributes of transportation information applications have a significant effect on Perceived usefulness and Perceived Ease of Use respectively. The Perceived usefulness and Perceived Ease of Use have affected significantly users' satisfaction respectively, so consequentially this shows effect relationship leading to reuse intention. CONCLUSIONS : The Perceived usefulness and Perceived Ease of Use all for the transportation information applications were shown to influence significantly on the satisfaction. With this kind of result, if users obtain positive outcomes such as travel time reduction or effective roles on their tasks through the transportation information applications, they feel the satisfaction for using and eventually these affect positively to the reuse intention of those transportation information applications.
4,000원
19.
2013.10
구독 인증기관 무료, 개인회원 유료
PURPOSES : This study attempts to design and establish the road surface condition detection system by using the image processing that is expected to help implement the low-cost and high-efficiency road information detection system by examining technology trends in the field of road surface condition information detection and related case studies. METHODS : Adapted visual information collecting method(setting a stereo camera outside of the vehicle) and visual information algorithm(transform a Wavelet Transform, using the K-means clustering) Experiments and Analysis on Real-road, just as four states(Dry, Wet, Snow, Ice). RESULTS : Test results showed that detection rate of 95% or more was found under the wet road surface, and the detection rate of 85% or more in snowy road surface. However, the low detection rate of 30% was found under the icy road surface. CONCLUSIONS : As a method to improve the detection rate of the mobile road surface condition information detection system developed in this study, more accurate phase analysis in the image processing process was needed. If periodic synchronization through automatic settings of the camera according to weather or ambient light was not made at the time of image acquisition, a significant change in the values of polarization coefficients occurs.
4,000원
20.
2013.10
구독 인증기관 무료, 개인회원 유료
PURPOSES : This research is to analyze the influence in terms of misreading rate and legibility time for drivers when condensation occurs on the road signs. METHODS : In this research, the dew occurred road signs provided to drivers to measure legibility time and misreading rate to compare with normal road sign. In order to identify the difference of legibility time between normal road sign and dew occurred road sign, the T-test and ANOVA test were used. And the vision system was used to recognize the region of dew occurrence on the road sign, then the brightness of dew occurrence region on the road sign was changed to check the misreading rate of drivers according to the change rate of brightness. RESULTS : The legibility times were measured 2.65s for normal road sign and 4.08s for dew occurrence road sign and misreading rates were measured 2.8% for normal road sign, 21.7% for dew occurrence road sign.
4,000원
1
2
